EEWORLDEEWORLDEEWORLD

Part Number

Search

77311-87012

Description
Board Connector, 12 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle,
CategoryThe connector    The connector   
File Size253KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

77311-87012 Overview

Board Connector, 12 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle,

77311-87012 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid1600255533
Reach Compliance Codecompliant
ECCN codeEAR99
body width0.094 inch
subject depth0.1 inch
body length1.2 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (15) OVER NICKEL
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
DIN complianceNO
Filter functionNO
IEC complianceNO
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee0
MIL complianceNO
Plug contact pitch0.1 inch
Mixed contactsNO
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
OptionsGENERAL PURPOSE
PCB contact patternRECTANGULAR
Plating thickness15u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts12
UL Flammability Code94V-0
PDS: Rev :CH
STATUS:Released
Printed: Oct 15, 2015
EPCS chip programming problem
I want to ask, after programming the EPCS chip through the CONFIG port, if I do not unplug the download line, the FPGA will not start up when I power it on again, nSTATUS will be pulled low, and CONF_...
eeleader-mcu FPGA/CPLD
Questions about multisim simulation
I was recently simulating a 555 oscillator. The square wave I output was input to a voltage follower and then connected to an integrator to get a triangle wave. The problem is as shown in the figure b...
音速兔 Analog electronics
Help, STM32F103 ADC problem
I use two ADCs for data acquisition. No matter in independent mode or synchronous mode, PA0 (channel 0) will have burr-like signals, and PA1 (channel 1) will have a level of about 1.7V (half of the 3....
laowen_110 stm32/stm8
TLC adopts AC voltage
I want to use TLC2543 to collect the instantaneous value of AC. The frequency of AC signal is only 50HZ. I wonder if the speed can be increased in time?...
晴歌 Analogue and Mixed Signal
Design of audio products based on DSP
With the acceleration of the digitalization process, digital signals will replace more analog signal environments. Since 2004, the application of DSP in consumer electronics will enter people's lives ...
fish001 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 289  740  1276  2106  285  6  15  26  43  25 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号