The RPP20 series 2:1 input range DC/DC converters are ideal for high end industrial applications and COTS Military
applications where a very wide operating temperature range of -45°C to +115°C is required. Although the case size
is very compact, the converter contains a built-in EMC filter EN-55022 Class B without the need for any external
components. The RPP20 is available in a ribbed case style for active cooling. They are UL-60950-1 certified.
rranty
Selection Guide
Part
Number
RPP20-2412S
Input
Voltage Range
[VDC]
18-36
Notes:
Note1:
Input
Current
[mA]
940
Output
Voltage
[VDC]
12
Output
Current
[mA]
1670
Efficiency
typ.
[%]
90
Max. Capacitive
Load
[µF]
1000
Typical values at nominal input voltage and full load.
Specifications
(measured @ ta= 25°C, nominal input voltage, full load and after warm-up)
BASIC CHARACTERISTICS
Parameter
Input Voltage Range
Transient Input Voltage
Inrush Current
Under Voltage Lockout
Remote ON/OFF
Remote OFF Input Voltage
Start-up Time
Internal Operating Frequency
Output Voltage Trimming
Efficiency
Minimum Load
Output Ripple and Noise
20MHz limited, 1µF output MLCC
typ. Vin, full load
89%
0%
120mVp-p
180mVp-p
* ICE Technology
ICE (Innovation in Converter Excellence)
uses state-of-the-art techniques to minimise
internal power dissipation and to increase
the internal temperature limits to extend the
ambient operating temperature range to the
maximum.
Condition
nom. Vin= 24VDC
≤100ms
with EMC Filter
without EMC Filter
DC-DC ON
DC-DC OFF
ON / high logic
OFF / low logic
nominal input
when use CTRL function
Min.
18VDC
Typ.
24VDC
Max.
36VDC
50VDC
20A
40A
E224736
17.5VDC
Open, 4.5V
Short, 0V
5mA
20ms
270kHz
300kHz
±10%
90%
330kHz
17VDC
5.5V
1.2V
UL-60950-1 Certified
EN-55022 Certified
Efficiency vs. Load
100
100
90
90
100
100
90
90
Efficiency vs. Input Voltage
Efficiency [%]
Efficiency [%]
80
80
70
70
60
60
50
50
18Vin
18Vin
24Vin
24Vin
36Vin
36Vin
10 20 30 40 50 60 70 80 90 100
10 20 30 40 50 60 70 80 90 100
Efficiency [%]
Efficiency [%]
80
80
70
70
60
60
50
50
18 20 22 24 26 28 30 32 34 36
18 20 22 24 26 28 30 32 34 36
Load [%]
Load [%]
Input Voltage [V]
Input Voltage [V]
50
50
continued on next page
REV.: 3/2016
RPP-1
emperature [°C]
emperature [°C]
www.recom-power.com
40
40
35
35
45
45
RPP20-2412S
DC/DC Converter
Trimming Output Voltage
Only the single output converters have a trim function that allows users to adjust the output voltage from +10% to -10%, please refer to
the trim table that follow for details. Adjustment to the output voltage can be used with a simple fixed resistor as shown in Figures 1 and 2.
A single fixed resistor can increase or decrease the output voltage depending on its connection. Resistor should be located close to the converter.
If the trim function is not used, leave the trim pin open.
Trim adjustments higher than the specified range can have an adverse effect on the converter´s performance and are not recommended.
Excessive voltage differences between output voltage sense voltage, in conjunction with trim adjustment of the output voltage; can cause
the OVP circuitry to activate. Thermal derating is based on maximum output current and voltage at the converter´s output pins. Use of
the trim and sense function can cause output voltages to increase, thereby increasing output power beyond the converter´s specified rating.
Therefore: (Vout at Pins) X (Iout)
≤
rated output power.
Series
Specifications
(measured @ ta= 25°C, nominal input voltage, full load and after warm-up)
+V
IN
CTRL
-V
IN
+V
OUT
TRIM
R
TRIM
UP
-V
OUT
+V
IN
+V
OUT
TRIM
R
TRIM
DOWN
-V
OUT
LOAD
CTRL
-V
IN
LOAD
Figure 1.
Trim connections to increase
output voltage using fixed resistors
Trim up resistor value (KW)
Vout
1%
2%
3%
4%
46.3
5%
32.1
6%
22.4
7%
15.4
8%
9.8
9%
6.5
10%
3.2
Vout
Figure 2.
Trim connections to decrease output
voltage using fixed resistors
Trim down resistor value (KW)
-1%
-2%
-3%
-4%
53.1
-5%
35.5
-6%
24.0
-7%
16.0
-8%
9.7
-9% -10%
5.0
1.3
12VDC
322.2 137.2 81.1
12VDC
238.7 113.1 68.2
REGULATIONS
Parameter
Output Voltage Accuracy
Line Voltage Regulation
Load Voltage Regulation
Transient Response
Transient Peak Deviation
Condition
50% load
low line to high line
10% to 100% load
25% load step change,
ΔIo/Δt=2.5A/us
25% load step change,
ΔIo/Δt=2.5A/us
Value
±1.5% max.
±0.3% max.
±0.5% max.
800µs typ.
±2%Vout max.
PROTECTIONS
Parameter
Output Power Protection (OPP)
Over Voltage Protection (OVP)
Over Temperature Protection (OTP)
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Notes:
Note2:
RPP-2
Condition
current limit
10% load
case temperature
I/P to O/P, at 70% RH
I/P to Case, O/P to Case
I/P to O/P , at 70% RH
I/P to O/P
This Power Module is not internally fused. A input fuse must be always used. Recommended Fuse: T1.6A
REV.: 3/2016
Value
120% typ.
120% typ.
120°C, auto-recovery
2250VDC / 1 Minute
1500VDC / 1 Minute
100MW min.
1500pF typ.
www.recom-power.com
RPP20-2412S
DC/DC Converter
ENVIRONMENTAL
Parameter
100
90
Series
100
Specifications
(measured @ ta= 25°C, nominal input voltage, full load and after warm-up)
Condition
Value
95%, non condensing
±0.04% / °C max.
7.2°C/W
7.8°C/W
Efficiency [%]
Temperature Coefficient
Thermal Impedance
Operating Temperature Range
Maximum Case Temperature
MTBF
80
natural convection, mounting at FR4
(254x254mm) PCB
70
vertical
horizontal
Efficiency [%]
100
Relative Humidity
90
80
70
60
50
start up at -45°C
according to MIL-HDBK-217F (+50°C G.B.)
10
according
30
BellCore-TR-332 (+50°C G.B.)
80
20
to
40 50 60 70
18Vin
24Vin
36Vin
90
-45°C to (see calculation)
60
+115°C
50
768 x 10
3
hours
1572 x
hours
18 20
10
3
22 24
26
Derating Graph
(Ta= +25°C, natural convection, typ. Vin and vertical mounting)
Load [%]
Input V
50
Case Temperature [°C]
45
40
35
30
25
0
10
20
30
40
50
60
70
80
90 100
Load [%]
Calculation
R
thcase-ambient
= 7.2°C/W (vertical)
R
thcase-ambient
= 7.8°C/W (horizontal)
R
thcase-ambient
=
T
case
- T
ambient
P
dissipation
P
=
OUTapp
- P
OUTapp
h
T
case
T
ambient
P
dissipation
P
IN
P
OUT
h
= Case Temperature
= Environment Temperature
= Internal losses
= Input Power
= Output Power
= Efficiency under given Operating Conditions
P
dissipation
= P
IN
- P
OUT
R
thcase-ambient
= Thermal Impedance
Practical Example:
Take the RPP20-2412S with 50% load. What is the maximum ambient operating temperature? Use converter vertical in application.
Eff
min
= 89% @ V
nom
P
OUT
= 20W
P
OUTapp
= 20 x 0.5 = 10W
P
dissipation
=
P
OUTapp
- P
OUTapp
h
R
th
=
T
casemax
- T
ambient
P
dissipation
--> 7.2°C/W =
115°C - T
ambient
1.24W
h
= ~88% (from Eff vs Load Graph)
10
P
dissipation
=
- 10 = 1.24W
0.89
T
ambientmax
= 106.1°C
continued on next page
www.recom-power.com
REV.: 3/2016
RPP-3
RPP20-2412S
DC/DC Converter
Soldering
Hand Soldering
Hand Soldering is the least preferred method because the amount of
solder applied, the time the soldering iron is held on the joint, the
temperature of the iron and the temperature of the solder joint are
variable.
The recommended hand soldering guideline is listed in Table 1. The
suggested soldering process must keep the power module’s internal
temperature below the critical temperature of 217°C continuously.
Table 1 Hand-Soldering Guideline
Parameter
Soldering
Iron Wattage
Tip
Temperature
Soldering Time
Single-side
Circuit Boad
90W
385 ±10°C
2-6 seconds
Double-side
Circuit Board
90W
420 ±10°C
4-10 seconds
Multi-layers
Circuit Board
Wave Soldering
High temperature and long soldering time will result in IMC layer
increasing in thickness and thereby shorten the solder joint lifetime.
Therefore the peak temperature over 245°C is not suggested due
to the potential reliability risk of components under continuous high-
temperature. In the meanwhile, the soldering time of temperature
above 217°C should be less than 90 seconds. Please refer to the sol-
dering profile below for recommended temperature profile parameters.
Series
Specifications
(measured @ ta= 25°C, nominal input voltage, full load and after warm-up)
T
emp
Peak T
emp. 240 - 245°C
217°C
90W
420 ±10°C
4-10 seconds
Ramp downmax. 4°C/sec
200°C
150°C
Preheat time100-140 sec.
Time Limited 90sec.above 217°C
25°C
Ramp upmax. 3°C/sec
Time
SAFETY AND CERTIFICATIONS
Certificate Type (Safety)
Information Technology Equipment, General Requirements for Safety
Report Number
E224236
Standard
UL-60950-1, 1st Edition
Certificate Type (Environmental)
Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement
ESD Immunity Test
RF Field Strengh Susceptibility Test
Electrical Fast Transient Test / Burst Immunity Text
Surge Immunity Test
Conducted Disturbance Susceptibility Test
Vibration
Thermal Cycling (complies with MIL-STD-810F)
Shock
Condition
±8kV Air Discharge,
±6kV Contact Discharge
10V/m
±4kV Applied
±4kV Applied
10V rms
50-150Hz, along X, Y and Z
12 cycles
5g / 30ms
Standard / Criterion
EN55022, Class B
IEC61000-4-2, Criteria B
IEC61000-4-3, Criteria A
IEC61000-4-4, Criteria B
IEC61000-4-5, Criteria B
IEC61000-4-6, Criteria A
EN60068-2-6
EN60068-2-14
EN60068-2-27
EMC Filtering - Suggestions
+V
IN
D1
C4
UR1
C1
C6
L1
C2
C3
C5
DUT
C7
Load
It is recommended to add UR1, D1 and C1 in railway
application. C1, L1, C2 and C3 can be modified for
required EMI standards. To meet EN61000-4-2, module
case should be earth grounded. We offer independent
case pin option on request, the location is upon pin 1.
-V
IN
Standard
EN55022 Class B
EN61000-4-2, 3, 4, 5, 6
UR1
MOV 14D361K
D1
50V / 9A
C1
1.5µF / 250V
N/A
L1
550µH ±20%
N/A
C2
6.8µF / 50V
N/A
C3
330µF / 50V
C4, C5, C6, C7
0.47nF Y1-Cap
RPP-4
REV.: 3/2016
www.recom-power.com
RPP20-2412S
DC/DC Converter
DIMENSION AND PHYSICAL CHARACTERISTICS
Parameter
Material
(3)
Series
Value
Aluminium
40.6 x 25.4 x 12.7mm
27g
40.6
Specifications
(measured @ ta= 25°C, nominal input voltage, full load and after warm-up)
Package Dimension (LxWxH)
Package Weight
Dimension Drawing (mm)
25.4
2.54
11.68
9.14
4.32
5.08
Sandoff
=1.02
dia. 1.0
20.32
Bottom View
5.08
7.62
3
1
2
6
10.16
Pin Connections
Pin #
Single
1
2
3
4
5
6
Tolerance
:
+Vin
-Vin
+Vout
Trim
-Vout
CTRL
4
10.16
5
±
0.8mm
Notes:
Note3:
To ensure a good all-round electrical contact, the bottom plate is pressed firmly into place into the aluminium case.The hydraulic press can
leave tooling marks and deformations to both the case and plate. The case is anodised aluminium, so there will be natural variations in the case
colour and the aluminium is not scratch resistant. Any resultant marks, scratches and colour varations are cosmetic only and do not affect the
operation or performance of the converters.
INSTALLATION and APPLICATION
Test Set-up
5µH
in
50Ω
out
rcvr
Printed Circuit Board
50 Ohm termination
Product
+
DC
Power
Source
LISN
Filter
(if used)
5µH
in
50Ω
out
rcvr
-
LISN
1m Twisted Pair
Resistive
Load
Optional Connection
to Earth Ground
50 Ohm input
EMC
Reciever
Computer
PACKAGING INFORMATION
Parameter
Packaging Dimension (LxWxH)
Packaging Quantity
Storage Temperature Range
Type
Tube
Value
160.0 x 45.0 x 16.0mm
5pcs
-55°C to +125°C
The product information and specifications are subject to change without prior notice. RECOM products are not authorized for use in safety-critical applications (such as life support) without RECOM’s explicit written
consent. A safety-critical application is defined as an application where a failure of a RECOM product may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The buyer
shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications.
The altera FPGA chip supports JTAG online download mode and AS download mode. In the JTAG download mode, the program is burned into the FPGA chip and runs directly after the JTAG download is completed...
/******************************************* Development environment: CCSv5 Program function: Use the timer's timing capture mode to make a simple frequency meter Program description: Can measure squa...
Talk about the meaning of the following program void IsrIRQ() { int count = 0; unsigned int isr_pending; unsigned int isr_mask = 0x00000001; unsigned int isr_mask_set = rINTMSK; /* Read interrupt mask...
[font=微软雅黑]A friend in the forum has been wanting to buy this series of chips for a long time, but has been unable to find a channel. Today, he asked several distributors he often contacts, but they a...
The Espressif IDF API reference document describes the limitations of the ESP32 built-in ADC and provides a (partial) solution to improve its accuracy by using chip-specific calibration values stored ...
There are many different ways of human-computer interaction. The more common ones are listed below:
Mouse interaction: Using a mouse to operate a computer and interact was the most common human...[Details]
On August 25th, SK Hynix announced that it has completed development and entered mass production of its 321-layer, 2Tb QLC NAND flash memory product. This achievement marks the world's first applic...[Details]
Common Mode Semiconductor has officially released its latest generation of power management ICs—the GM6506 series. This fully integrated high-frequency synchronous rectification step-down p...[Details]
As the scale and business applications of national e-government networks continue to expand, the data and services transmitted over them are becoming increasingly sensitive and critical. To protect...[Details]
With the rapid development of electric vehicles in my country, people are beginning to pay attention to the issue of radiation from electric vehicles. We all know that mobile phones emit radiation,...[Details]
Normally, we determine our location and where we want to go by comparing our surroundings with observation and simple GPS tools. However, this kind of reasoning is very difficult for self-driving c...[Details]
With the continuous development of the industrial automation industry, we are seeing an increasing number of intelligent devices using flexible, efficient, and precise robotic arms to p...[Details]
A multilevel inverter converts a DC signal into a multilevel staircase waveform. Instead of a straight positive-negative output waveform, the output waveform of a multilevel inverter alternates in ...[Details]
1. Fault phenomenon and cause analysis
1. During the operation of the equipment, the expansion sleeve is subjected to a large torque, and the mating surfaces of the shaft and the sleeve move...[Details]
The difference between a series inverter and a parallel inverter is that they use different oscillation circuits. A series inverter connects L, R, and C in series, while a parallel inverter connect...[Details]
In the field of communications power supplies, AC/DC rectifier power supplies are called primary power supplies or basic power supplies, while DC/DC converters are called secondary power supplies. ...[Details]
Tires are a very important component for cars. They are related to the driving experience of the vehicle. We are almost inseparable from cars in our daily lives. For tires, according to the role of...[Details]
introduction
In today's busy society, people experience chronic high stress, which in turn poses a significant threat to our health. Therefore, effectively relieving stress has become a pr...[Details]
01. Introduction
As in-vehicle networks migrate from the CAN
bus
to
Ethernet
, traditional millisecond-level synchronization accuracy can no longer meet the requirements of mul...[Details]
At present, the most troubling thing about pure electric vehicles as new energy sources is not only the range anxiety, but also the disadvantage of long charging time. At present, ternary lithium b...[Details]
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
