EEWORLDEEWORLDEEWORLD

Part Number

Search

DS1099U-01M

Description
Programmable Oscillators Low-Frequency Dual EconOscillator
CategoryPassive components   
File Size107KB,6 Pages
ManufacturerMaxim
Websitehttps://www.maximintegrated.com/en.html
Download Datasheet Parametric Compare View All

DS1099U-01M Online Shopping

Suppliers Part Number Price MOQ In stock  
DS1099U-01M - - View Buy Now

DS1099U-01M Overview

Programmable Oscillators Low-Frequency Dual EconOscillator

DS1099U-01M Parametric

Parameter NameAttribute value
Product CategoryProgrammable Oscillators
ManufacturerMaxim
RoHSNo
PackagingTube
Factory Pack Quantity50
Rev 1; 9/07
Low-Frequency Dual EconOscillator
General Description
The DS1099 is a low-cost, low-power, low-frequency
silicon oscillator that generates two square-wave out-
puts with frequencies between 0.25Hz and 1.048MHz.
Individual output enables allow both outputs to be
enabled/disabled independently. Both outputs are
capable of sinking 16mA, allowing them to directly
interface to light-emitting diodes (LEDs) as well as other
external circuitry. The DS1099 operates over a wide
supply voltage, making it suitable for both 3V and 5V
systems. The device is shipped from the factory custom
programmed and calibrated, ready to be inserted into
the end application.
Contact the factory for custom frequencies or
requirements.
Features
Low-Cost, Low-Frequency EconOscillator™ with
Dual Outputs
Factory Programmed
Output Frequencies Independently Programmable
from 0.25Hz to 1.048MHz
2.7V to 5.5V Single-Supply Operation
No External Timing Components Required
Independent Output Enables
CMOS/TTL-Compatible Outputs
Oscillator Outputs Capable of Sinking 16mA to
Directly Drive LEDs
Relieves Microprocessor of Periodic Interrupt
Low-Power Consumption
Operating Temperature Range: -40°C to +125°C
±100ppm/°C Temp Drift (MAX)
DS1099
Applications
Flashing LED Status Indicators
Consumer Appliances
Automotive
Servers
Printers
Switch-Mode Power Supplies
Ordering Information
PART
DS1099U-
O
TEMP RANGE
1
-40°C to +125°C
PIN-PACKAGE
8 μSOP
*Where
α
0
and
α
1
specify the factory programmed divider set-
tings for OUT0 and OUT1, respectively.
Ordering information is continued on the last page.
EconOscillator is a trademark of Dallas Semiconductor.
Typical Operating Circuit
V
CC
V
CC
Pin Configuration
TOP VIEW
V
CC
OE0
OE1
N.C.
N.C.
OUT1 1
OUT0
OUT1
OUT0
V
CC
2
3
8
7
N.C.
N.C.
OE1
OEO
DS1099
GND
DS1099
6
5
GND 4
OE1 CAN INSTEAD
BE TIED TO V
CC
IF OUT1 IS NOT USED.
OUTPUTS CAPABLE OF
SINKING 16mA
μSOP
________________________________________________________________
Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.

DS1099U-01M Related Products

DS1099U-01M DS1099U-FF-T DS1099U-LU
Description Programmable Oscillators Low-Frequency Dual EconOscillator Programmable Oscillators Low-Frequency Dual EconOscillator
Product Category Programmable Oscillators Programmable Oscillators -
Manufacturer Maxim Maxim -
Detailed explanation of the switching power supply principle and various functional circuits
A detailed introduction to the internal functional modules of the switching power supply....
lczhoujq Analog electronics
Looking for a DSP expert who has developed TMS320C6701 for a fee
I'm looking for an old friend who has used the ancient DSP TMS320C6701. I have drawn two sets of boards, both of which cannot be run, and I can't find the problem. I'm looking for an old friend to hel...
瓜弟 MCU
Resonant switching power supply Yang Bo's paper
I'm studying Yang Bo's "Topology Investigation for Front End DC/DC Power Conversion for Distributed Power System" recently, but I don't understand the English version. Does anyone have relevant Chines...
电子的雏鸟 Power technology
Can the line spacing of Altium Mechanical 13 layers without network be set?
Can the rules set the spacing between the green frames of the two components in the picture below? I don't know how to do it. What is the general spacing between components? Thank you...
大发明家 PCB Design
MSP430F5438A clock settings
[i=s]This post was last edited by fish001 on 2018-8-6 21:56[/i] Using MSP430F5438A, XT2 with an external 25MHz crystal oscillator, and writing a clock driver, it does not work properly. Now paste this...
fish001 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 92  2067  1252  914  250  2  42  26  19  6 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号