Operating Temperature Range ..........................-40°C to +85°C
Storage Temperature Range .............................-65°C to +160°C
Lead Temperature (soldering, 10s) .................................+300°C
Soldering Temperature (reflow) .......................................+260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
CC
= +2.7V to +5.5V, V
CM
= 0V, T
A
= -40°C to +85°C, unless otherwise noted. Typical values are at T
A
= +25°C.) (Note 1)
PARAMETER
Supply Voltage Range
Supply Current per Comparator
Shutdown Supply Current
Power-Supply Rejection Ratio
Common-Mode Voltage Range
Common-Mode Rejection Ratio
Input Offset Voltage
Input-Referred Hysteresis
Input Bias Current
Input Offset Current
OUT Output-Voltage High
OUT Output-Voltage Low
OUT Short-Circuit Current
Input Capacitance
SHDN
Input-Voltage High
SHDN
Input-Voltage Low
OUT Leakage Current
SHDN
Input Current
Propagation Delay
Propagation-Delay Skew
Propagation-Delay Matching
Between Channels
Output Rise/Fall Time
Shutdown Delay Time
2
SYMBOL
V
CC
I
CC
I
SD
PSRR
V
CMR
CMRR
V
OS
V
HYS
I
B
I
OS
V
OH
V
OL
I
SH
C
IN
V
IH
V
IL
I
OUT
I
SHDN
t
PD
t
SKEW
Δt
PD
t
R
/t
F
t
SD
MAX998 only
MAX998 only
V
CC
= 5.5V
V
CC
= 2.7V
CONDITIONS
Inferred from PSRR test
MIN
2.7
TYP
300
225
1
MAX
5.5
650
500
V
CC
- 1.2
UNITS
V
µA
nA
dB
V
dB
MAX998 only,
SHDN
= GND
2.7V < V
CC
< 5.5V
(Note 2)
-0.2V
≤
V
CM
≤
(V
CC
- 1.2V)
V
CC
= 5V (Note 3)
V
CC
= 5V (Note 4)
T
A
= +25°C
T
A
= T
MIN
to T
MAX
MAX976EUA, MAX998EUT
All others
0.3
0.5
63
-0.2
66
100
95
0.2
1.5
1.5
75
±5
±2
±3
5.0
4.0
300
±100
0.4
0.4
mV
mV
mV
nA
nA
V
V
mA
pF
V
I
SOURCE
= 2mA, V
CC
- V
OH
I
SINK
= 2mA
V
CC
= 5.5V
Sinking
Sourcing
0.65 x V
CC
0.1
0.1
74
90
3
0.2 x V
CC
1
1
Overdrive = 5mV
Overdrive = 50mV
28
20
2
1
1.6
5
40
200
200
V
nA
nA
ns
ns
ns
ns
µs
MAX998 only,
SHDN
= GND,
V
OUT
= 0V to V
CC
MAX998 only
C
LOAD
=10pF,
V
CC
= 5V (Note 5)
C
LOAD
=10pF (Note 6)
MAX976/MAX978 only
C
LOAD
=10pF
MAX998 only, V
CC
= 5V, I
CC
= 10% of typical
Maxim Integrated
MAX976/MAX978/MAX998
Single/Dual/Quad, SOT23, Single-Supply,
High-Speed, Low-Power Comparators
ELECTRICAL CHARACTERISTICS (continued)
(V
CC
= +2.7V to +5.5V, V
CM
= 0V, T
A
= -40°C to +85°C, unless otherwise noted. Typical values are at T
A
= +25°C.) (Note 1)
PARAMETER
Wake-Up from Shutdown
Power-Up Delay
SYMBOL
t
EN
t
PU
CONDITIONS
MAX998 only, V
CC
= 5V, I
CC
= 90% of typical
(Note 7)
V
CC
= 0V to 5V step, output valid
MIN
TYP
15
3
MAX
UNITS
µs
µs
Note 1:
The MAX998EUT specifications are 100% tested at T
A
= +25°C. Limits over the extended temperature range are guaran-
teed by design, not production tested.
Note 2:
Inferred from CMRR test. Either input can be driven to the absolute maximum limit without false output inversion, as long as
the other input is within the common-mode voltage range.
Note 3:
V
OS
is defined as the mean of trip points. The trip points are the extremities of the differential input voltage required to make
the comparator output change state (Figure 1).
Note 4:
The difference between the upper and lower trip points is equal to the width of the input-referred hysteresis zone (Figure 1).
Note 5:
Propagation Delay is guaranteed by design. For low overdrive conditions, V
TRIP
(Figure 1) is added to the overdrive.
Note 6:
Propagation-Delay Skew is the difference between the positive-going and the negative-going propagation delay.
京公网安备 11010802033920号
EEWORLD
