DEMO KIT AVAILABLE
DS2149
5V T1/J1 Line Interface Unit
www.maxim-ic.com
GENERAL DESCRIPTION
The DS2149 is a fully integrated LIU for long-
haul or short-haul T1 applications over twisted-
pair installations. It interfaces to two twisted-pair
lines—one pair for transmit and one pair for
receive through an appropriate network
interface. The device can be configured for
control through software or hardware mode.
Software control is accomplished over a serial
port, in hardware mode; individual pin settings
allow standalone operation. The device provides
a precise, crystal-less jitter attenuator that can be
placed in either the transmit or receive path.
FEATURES
§
§
§
§
§
§
§
Fully Integrated Line Interface Unit (LIU)
Pin Compatible with LevelOne LXT362
Supports Both Long Haul and Short Haul
Crystal-Less Jitter Attenuator
Jitter Attenuator Programmable for Transmit
or Receive Path
Meets ANSI T1.102, T1.403, T1.408, and
AT&T 62411
Usable Receive Sensitivity of 0dB to -36dB
That Allows the Device to Operate on
0.63mm (22AWG) Cables Up to 6k Feet in
Length
Five Line Build-Out Settings for Short-Haul
Applications
Four CSU Filters from 0dB to -22.5dB
Transmit/Receive Performance Monitors
with Driver-Fail, Monitor-Open, and Loss-
of-Signal Outputs
Bipolar or NRZ Interface
Programmable B8ZS Encoder/Decoder
QRSS Generator/Detector
Local, Remote, and Analog Loopbacks
Generates and Detects In-Band Loop-Up and
Loop-Down Codes
Serial Interface Provides Access to Control
Registers
§
§
§
§
§
§
§
§
§
APPLICATIONS
Routers
Data Service Units (DSUs)
Channel Service Units (CSUs)
Muxes
Switches
Channel Banks
T1/E1 Test Equipment
PIN CONFIGURATION
TOP VIEW
4 3 2 1 28 27 26
5
6
7
8
9
10
11
25
24
23
22
21
20
19
ORDERING INFORMATION
PART
DS2149Q
DS2149QN
TEMP RANGE
0°C to +70°C
-40°C to +85°C
PIN-PACKAGE
28 PLCC
28 PLCC
DS2149
12 13 14 15 16 17 18
PLCC
Note:
Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple revisions of any device
may be simultaneously available through various sales channels. For information about device errata, click here:
www.maxim-ic.com/errata.
1 of 32
REV: 113004
DS2149
TABLE OF CONTENTS
1.
DETAILED DESCRIPTION ................................................................................................. 4
2.
OPERATING MODES......................................................................................................... 5
3.
INITIALIZATION AND RESET............................................................................................ 9
4.
REGISTER DEFINITIONS .................................................................................................. 9
5.
TRANSMITTER................................................................................................................... 15
5.1
T
RANSMIT
D
IGITAL
D
ATA
I
NTERFACE
................................................................................... 15
5.2
T
RANSMIT
M
ONITORING
...................................................................................................... 15
5.3
T
RANSMIT
I
DLE
M
ODE
......................................................................................................... 15
5.4
T
RANSMIT
P
ULSE
S
HAPE
.................................................................................................... 15
6.
RECEIVER.......................................................................................................................... 15
6.1
R
ECEIVE
E
QUALIZER
.......................................................................................................... 15
6.2
R
ECEIVE
D
ATA
R
ECOVERY
.................................................................................................. 15
6.3
R
ECEIVE
D
IGITAL
-D
ATA
I
NTERFACE
..................................................................................... 16
6.4
R
ECEIVE
M
ONITOR
M
ODE
................................................................................................... 16
7.
JITTER ATTENUATION ..................................................................................................... 16
8.
HARDWARE MODE ........................................................................................................... 16
9.
SOFTWARE MODE ............................................................................................................ 17
9.1
I
NTERRUPT
H
ANDLING
........................................................................................................ 17
10.
DIAGNOSTIC MODE OPERATION.................................................................................... 19
10.1 L
OOPBACK
M
ODES
............................................................................................................. 20
10.1.1
10.1.2
10.1.3
10.1.4
10.1.5
Local Loopback (LLB).................................................................................................................20
Analog Loopback (ALB)..............................................................................................................20
Remote Loopback (RLB) ............................................................................................................20
Network Loopback......................................................................................................................20
Dual Loopback ...........................................................................................................................20
10.2
I
NTERNAL
P
ATTERN
G
ENERATION AND
D
ETECTION
............................................................... 21
10.2.1 Transmit Alarm-Indication Signal (TAIS).....................................................................................21
10.2.2 Quasirandom Signal Source (QRSS) .........................................................................................21
10.2.3 In-Band Network Loop-Up or Loop-Down Code Generator.........................................................22
10.3
10.3.1
10.3.2
10.3.3
10.3.4
E
RROR
I
NSERTION AND
D
ETECTION
..................................................................................... 22
Bipolar Violation Insertion (INSBPV)...........................................................................................22
Logic Error Insertion (INSLE)......................................................................................................22
Logic Error Detection (QPD).......................................................................................................22
Bipolar Violation Detection (BPV) ...............................................................................................22
10.4
10.4.1
10.4.2
10.4.3
10.4.4
A
LARM
M
ONITORING
........................................................................................................... 23
Receive-Carrier Loss (RCL) .......................................................................................................23
Alarm-Indication-Signal Detection (AIS)......................................................................................23
Driver-Fail Monitor-Open (DFMO) ..............................................................................................23
Jitter Attenuator Limit Trip (JALT) ...............................................................................................23
10.5
11.
12.
13.
O
THER
D
IAGNOSTIC
R
EPORTS
............................................................................................ 23
NETWORK INTERFACE .................................................................................................... 24
DC CHARACTERISTICS .................................................................................................... 28
PACKAGE INFORMATION ................................................................................................ 32
2 of 32
10.5.1 Receive Line-Attenuation Indication ...........................................................................................23
DS2149
LIST OF FIGURES
Figure 1-1. Block Diagram.......................................................................................................................................
4
Figure 2-1. Hardware Mode Pinout
........................................................................................................................ 6
Figure 2-2. Serial Port Mode Pinout.......................................................................................................................
6
Figure 9-1. Serial Data Port Operation for Read Access..................................................................................
18
Figure 9-2. Serial Data Port Operation for Write Access..................................................................................
18
Figure 10-1. Loopbacks in the DS2149 Block Diagram....................................................................................
21
Figure 11-1. Basic Network Interface
.................................................................................................................. 25
Figure 11-2. T1 Transmit Pulse Template
.......................................................................................................... 26
Figure 11-3. Jitter Tolerance
................................................................................................................................. 27
Figure 11-4. Jitter Attenuation...............................................................................................................................
27
Figure 12-1. Serial Bus Read Timing (MODE1 = 1)
.......................................................................................... 29
Figure 12-2. Serial Bus Write Timing (MODE1 = 1)
.......................................................................................... 29
Figure 12-3. AC Characteristics for Receive Side
............................................................................................. 30
Figure 12-4. AC Characteristics for Transmit Side
............................................................................................ 31
LIST OF TABLES
Table 2-A. Operating Modes
................................................................................................................................... 5
Table 2-B. Control Pins for Hardware and Software Modes
.............................................................................. 5
Table 2-C. Signal Descriptions
............................................................................................................................... 7
Table 4-A. Register Map
.......................................................................................................................................... 9
Table 4-B. Register Bit Positions............................................................................................................................
9
Table 4-C. Jitter Attenuator Selection..................................................................................................................
10
Table 4-D. Line Code and Interface Selection
................................................................................................... 10
Table 4-E. Line Build-out Selection......................................................................................................................
10
Table 4-F. Data Pattern Selection
........................................................................................................................ 11
Table 9-A. CLKE Pin Selection.............................................................................................................................
17
Table 9-B. Control and Operation Mode Selection............................................................................................
19
Table 10-A. Diagnostic Modes..............................................................................................................................
19
Table 11-A. Specifications for Receive Transformer.........................................................................................
24
Table 11-B. Specifications for Transmit Transformer........................................................................................
24
Table 11-C. Transformer Turns Ratio vs. Series Resistance
.......................................................................... 24
3 of 32
DS2149
1. DETAILED DESCRIPTION
The DS2149 is a complete T1 line interface unit (LIU) for short-haul and long-haul applications. Receive
sensitivity adjusts automatically to the incoming signal and can be limited to -18dB, -26dB, or
-36dB. The device can generate the necessary DSX-1 line build-outs or CSU line build-outs of 0dB,
-7.5dB, -15dB, and -22.5dB. The on-board crystal-less jitter attenuator requires a 1.544MHz reference
clock. The jitter attenuator FIFO is selectable to either 32 bits or 128 bits in depth and can be placed in
either the transmit or receive data paths. The DS2149 has diagnostic capabilities such as loopbacks and
QRSS pattern generation and detection. The device can also generate and detect the in-band loop-up and
loop-down codes specified in AT&T 62411. The device can be configured for control using a serial
interface, or for hardware mode. The device fully meets all of the latest T1 specifications including ANSI
T1.102-1999, ANSI T1.403-1999, ANSI T1.408, and AT&T 62411.
Figure 1-1. Block Diagram
MCLK
VCO / PLL
NLOOP
RCL/QPD
Clock / Data
Recovery
B8ZS Decoder
In Band Loop
Code Detector
QRSS Detector
Peak Detect
AIS detect
Filter
RRING
RTIP
RCL Detector
RCLK
RPOS
RNEG
Analog Loopback
Local Loopback
Jitter Attenuator
Remote Loopback
In Band Loop gen.
Logic Error Insert
Wave Shaping
Line Drivers
B8ZS Encoder
CSU Filters
Trnasmit AIS
LOTC mux
QRSS
TRING
TTIP
TCLK
TPOS
TNEG
Power connections
Hardware Interface
Serial Interface
JASEL
L0
L1
L2
L3
LLB
RLB
TBL/QRSS
4 of 32
MODE0
MODE1
VSM
TVDD
VDD
GND
GND
INT
CLKE
SCLK
SDI
SDO
CS
DS2149
2. OPERATING MODES
The DS2149 has several pins with multiple functions and names according to the selected operating
mode. These operating modes are summarized in the tables below.
Table 2-A. Operating Modes
PIN
1
2
3
4
6
7
8
13
16
19
20
QRSS DISABLED
BIPOLAR
NRZ
MCLK
TCLK
TPOS
TNEG
RNEG
RPOS
TDATA
INSBPV
BPV
RDATA
RCLK
TTIP
TRING
RTIP
RRING
INSLER
INSBPV
RNEG
RPOS
BPV
RDATA
QRSS ENABLED
BIPOLAR
NRZ
Control pins are affected by serial port and hardware modes.
Table 2-B. Control Pins for Hardware and Software Modes
PIN
5
9
11
12
23
24
25
17
18
26
27
28
HARDWARE MODE
NRZ
QRSS
MODE1
MODE0
JASEL
RCL
RCL/QPD
L0
L1
L2
L3
NLOOP
RLB
NLB
LLB
ALB
TAIS
QRSS
SERIAL PORT MODE
NRZ
QRSS
MODE1
MODE0
N.C.
RCL
RCL/QPD
INT
SDI
SDO
N.C.
NLOOP
CS
SCLK
CLKE
5 of 32
京公网安备 11010802033920号
EEWORLD
