Training
Profile
You Might Like
Recommended Posts
- 48V to 12V output current is 10A what is the input and output current
- Thank you, God, please
-
PCB学徒
LED Zone
- LPC1343 Chinese Data Sheet --- Chinese translation, 4.30 update, basic part translated
- Haha, I still prefer to read Chinese data manuals. Unfortunately, foreigners do not pay much attention to the Chinese market and do not provide Chinese manuals at all. (So far, I have only seen AVR mi
-
tiankai001
NXP MCU
- How to achieve serial port (4v-3.3v) level matching through resistors
- Could you please give me some advice?
-
youn@g
Analog electronics
- When taskspawn assigns a task, the parameters include priority and stack size. How do I write them? I just got started with this.
- When taskspawn assigns a task, the parameters include priority and stack size. How should I write them? I just started to work on this. I see that the priority in the examples is mostly 90. If I creat
-
ttww007
Embedded System
- Brother who is familiar with op amps, please recommend a chip to me
- I need to increase the output voltage of a DAC from 0 to 3V to 0 to 4V. I use a 5V power supply and have no special requirements. The converted voltage is used to adjust 3525. I tried it myself with O
-
yup1983
Analog electronics
- NMOS tube on-state voltage test problem
- This is the data of an NMOS tube. When testing VGS(th), how many V should the VDS voltage be? The test conditions only state: ID=250uA, VDS=VGS, and it does not specify the V voltage used for VDS. I h
-
fdingy
Test/Measurement
Recommended Content
Web users are watching Change
- Does jpeg compressed data contain a file header?
- The use of volatile in TI DSP programming
- Looking for C language tutorial for MSP430 microcontroller
- Born only for uC, uS's growth process 16
- ucos iii time base variable overflow problem
- Please help me check if the signal acquisition program is OK. Is it correct that the signal processing program has been simulated separately?
- EEWORLD University - How to use independent measurement ADC to design high-precision CT phase meter
- A collection of selected PCB design resources, free points download for a limited time
- Equipped and ready to go, a must-have list for self-driving in Tibet
- STM32F769I-DISCO Review [1]—— Unboxing photos of "ST769 mobile phone"
- Please help me check if the program is correct! Thank you (circuit diagram attached)
- MCU model confirmation and decryption
- dsp6713 minimum system principle engineering file
- XDS100V2 simulates TI M3, pictures speak louder than words
- What does mmu initialization do? ? (Experts please come in)
- Current research trends and development directions of new gas sensors (Part 2)
- Future Trends of RFIC_mm-Wave Silicon Technology 60 GHz and Beyond
- Repost: The most awesome resignation letter from a post-80s generation
- Is there any QQ exchange group for Windows kernel development? Can you recommend a few suitable for beginners?
- [Zero-knowledge ESP8266 tutorial] Quick start 25 Blynk control RGB LED
- Need a 10uh inductor, ESR < 0.2Ω, saturation current > 0.8A
- Everyone cried for 8.5 yuan!
- May I ask the moderator and everyone, how to solve the following problem?
- How to burn the program to TM4C123G?
- About Skyeye fault-tolerant processing mode design
- Hiring embedded software engineer
- Twin-T Notch Filter
- CCS7.4 import engineering issues
- Automated transient test bench approach for LDO and buck regulators
- Solve it
Popular Components
Just Take a Look
Hot Downloads
- Example Programs for Sunplus MCU
- [Share] Wiring Questions
- FRGEWGFVDASFWDFDXSFEASFSAFSFSAF
- A tutorial book on data structures for Yan Weimin
- 5581.pdf Electron tube data sheet
- Introduction to Assembly Language
- IAR MSP430 project compilation and JTAG simulation debugging
- Design and Stability Analysis of LNA (Paper)
- 2-layer board impedance design
- MMS Packaging Program
MoreHot Articles
京公网安备 11010802033920号