Slide block for light-curing 3D printer

Schematic PCB

A LabVIEW vending machine example, source code

Schematic PCB

Open Source SCPI Programmable Precision Resistor Meter

A programmable resistor is an electronic device whose resistance can be adjusted, usually through a digital signal. Programmable resistors come in the form of integrated circuits (often called digital potentiometers) as well as stand-alone devices/expansion cards. There are many different applications, each with its own set of requirements.

​Range 1Ω - 999.999KΩ.

Schematic PCB

EEWorld netizens share experiences in national competitions

Schematic PCB

Output capacitor bank for signal power or dual supply headphone amplifier

This is a simple output capacitor bank for use in signal powered or dual supply headphone amplifiers. The output capacitor bank protects the headphones from DC current.​

Schematic PCB

3dfx Voodoo Memory Expansion Board - Revision 1.0

PCB for clipping onto Guillemot MAXI Gamer 3D Voodoo graphics accelerator. The common memory size for these cards is 4 MB. With the help of PCB you can get Voodoo up to 8 MB.

Schematic PCB

Escorna CPU 2.12: An open source hardware project geared towards robotics and programming for kids.

The basic Escornabot can be programmed to perform a series of actions using the robot's buttons. From this point of view, imagination is the only limit on possibility.

Schematic PCB

FORmod - FORD S/S DRIVE MODE

A simple circuit to disable automatic start-stop and set the default drive mode on a Ford vehicle.

Schematic PCB

Flexible PCB with three buttons

1 Layers PCB 11 x 48 mm Polyimide Flex, 0.1 mm, 1, Immersion gold (ENIG), Yellow Solder Mask, White silkscreen;

Schematic PCB

10x10cm 1.27mm perforated board

2-layer PCB 100 x 100 mm FR-4, 0.8 mm, 1, tinned with leads, green solder mask, white silkscreen;

Schematic PCB

10KHz-30MHz Mini WIHIP AKTIF Antenna

10KHz-30MHz Mini WIHIP AKTIF Antenna

Homemade flexible capacitive sensor

By CNC engraving a PCB in the following manner, the curved pad can perform capacitive sensing in 3 different directions and ultimately detect the 3D position of the finger.

Schematic PCB

pcie_x4: SYZYGY creates PCIe x4 add-in card

SYZYGY is an FPGA extension standard for medium to high speed interfaces. This breakout connects the SerDes in the SYZYGY-TXR connector to the card edge to act as a PCIe x4 add-in card. This breakout is very simple and can be made into a shorter SYZYGY pod.

Schematic PCB

pcie_x1: SYZYGY creates a compact PCIe x1 add-in card

SYZYGY is an FPGA extension standard for medium to high speed interfaces. This breakout connects the Channel 0 TX/RX SerDes from the SYZYGY-TXR connector to the edge of the card to act as a PCIe x1 add-in card.

Schematic PCB

memory-lcd-wing: Minimal wing for OrangeCrab

This design is a wing add-on that attaches to the OrangeCrab and adds a Sharp Memory LCD. 400x240 on/off pixels. The board is the size of the monitor.

Schematic PCB

Quadcopter Matlab simulation program

Quadcopter Matlab simulation program

Schematic PCB

51 microcontroller to make alarm clock

Use the Android cable to connect the voice chip and connect it to the computer. At this time, there is a removable disk on the computer, and then put the sound file into the removable disk... Materials used: Voice playback module Yabo 51 microcontroller (refer to this microcontroller The digital tube and the 8 free IO ports can be used) 3 10k resistors... Put the sound file into the voice chip and connect the data line and power line to the microcontroller. Use the keil tool to generate the hex file from the c program. And write it into the microcontroller...

Schematic PCB

labview car instrument program

It is composed of labview front panel and back panel controls.

Schematic PCB

Tool changing manipulator design

The manipulator is the main tool for exchanging tools in the automatic tool changer. It is responsible for sending the tools from the tool magazine to the spindle, and then returning the used tools from the spindle to the tool magazine. The design idea is to use the movement of the manipulator to change the tool of the machining center. The rotation of the manipulator is realized by a rotary pneumatic cylinder or a rotary pneumatic cylinder, and its power is realized by the drive system. The automatic tool changer of a machining center is usually composed of a tool magazine and a manipulator. It is a symbol of the machining center and a key link to the success or failure of the machining center. Therefore, all machining center manufacturers are working hard to develop automatic tool changers with fast action and high reliability in order to achieve good results in the fierce competition. Automatic tool changers are the core content of machining centers, and each manufacturer is keeping it secret. Very little relevant information is disclosed, especially the robot part. The knife extraction and knife insertion actions of the manipulator are mostly completed by the pneumatic cylinder or the action of the pneumatic cylinder. The entire manipulator is composed of a mechanical arm telescopic mechanism, a mechanical claw opening and closing mechanism, a rotary mechanism and a linear motion mechanism for loading and unloading tools.

Schematic PCB

Esai source code pure electric vehicle motor drive and vehicle control system based on DSP and bidirectional Z-source inverter

This project applies the bidirectional Z-source inverter to the motor drive system of pure electric vehicles. Using TMS320F2808 DSP as the control core, the SVPWM control technology based on the Z-source inverter is implemented.

Schematic PCB