S12ZVL32 RGB LED lighting reference design

K series hydraulic/pneumatic valve controller system

This valve controller system uses SB0800 octal valve controller IC with MCU and two power MOSFETs. The system can drive proportional and digital valves as well as system pumps. Monitoring and protection features protect the system from hazardous events such as short circuits, overcurrent or overvoltage, and other abnormal conditions.

S12G HVAC Control Reference Design

RDS12GHVAC is a reference design based on the 16-bit S12G ultra-reliable microcontroller. RDS12GHVAC consists of a central control board with a human-machine interface (HMI), a motor control board, a damper and a blower motor. It is used to realize the temperature, light, and humidity of automotive HVAC. and air quality sensing interface and configurable automatic climate control software algorithms to effectively control vehicle climate.

S12ZVM 12 V Electrical Fuel Pump (EFP) Reference Design

Schematic PCB

S32G2 Internet of Vehicles Reference Design

Schematic PCB

S32G3 Automotive Network Reference Design

Schematic PCB

OrangeBox Automotive Connectivity Domain Controller Development Platform

OrangeBox is a comprehensive development platform that provides a wide range of secure wireless connectivity to develop automotive solutions that meet the requirements of connected domain or zone controllers. OrangeBox integrates a scalable i.MX 8XLite applications processor, S32K security co-processor and the wireless connectivity required to enable secure automotive access, V2X, Wi-Fi, Bluetooth® LE, UWB and cellular connectivity between the vehicle and the outside world In a safe and secure manner.

GoldBox 3 Automotive Network Development Platform

Schematic PCB

Automotive area controller

The NXP Zone Control Proof of Concept (POC) platform is a zone development ecosystem for OEMs' POC efforts. It prototypes a vehicle-level zone architecture using an Ethernet backbone, addressing technical challenges with potential solutions and implementing key functions required for the zone architecture, including PDU gateways, PDU tunneling, DDS applications, TSN capabilities and performance benchmarking.

Smart battery charger based on LPC860 MCU

This smart battery charger is based on NXP's LPC860 cost-effective MCU, which provides customers with a reference design for smart battery charging applications and can be used for mobile devices such as handheld printers and walkie-talkies.

BlueBox 3.0 Automotive High Performance Computing (AHPC) Development Platform

Homemade 10KV electronic load

Commercial electronic loads are more expensive, especially high-power loads such as computer power supplies that must handle transient current spikes well above their nominal ratings (1800W spike for a 600W GPU) and should be tested under worst-case conditions to Ensure stability.

Schematic PCB

Breadboard without jumpers: Based on Raspberry Pi Pico, analog switch matrix replaces jumpers

Flirting with jumper caps is a common practice on most boards, but not this board, which is designed to replace all those wires with an analog switch matrix. All one has to do is plug in the device and make a virtual connection on the accompanying GUI. There are also many built-in functions such as DAC and ADC, and the circuit can be switched under the prototype as needed. It also has some LEDs embedded in the breadboard area that light up and provide visual cues that they are connected to each other.

Schematic PCB

An open source project for underwater sensor nodes based on single-pair Ethernet technology SPE (from tutorial to actual combat, English)

Single-Pair-Ethernet technology (SPE, Single-Pair-Ethernet) describes the transmission of Ethernet through only a pair of copper cores. In addition to transmitting data through Ethernet, it can also simultaneously provide power to terminal devices through PoDL (power supply over data lines).

Schematic PCB

Laser projector project made by teacher ChaN

2017 Electronic Competition Question B-Rolling Ball Control System National First Report

Schematic PCB

2017 National College Student Electronic Design Competition_Microgrid Simulation System (Question A) Design Report_National Second

Schematic PCB

2020 Electronic Competition G Question-Non-contact Object Size and Shape Measurement (Liaoning Petrochemical University)

Schematic PCB

2020 Electronic Competition Question F-Simple non-contact temperature measurement and identification device (Anhui Division)

Schematic PCB

Distributed temperature and humidity acquisition system based on STM32H745I

Schematic PCB