This solution is designed to create a size-optimized integrated power design for ADAS applications using the TDA3x SoC (no automotive battery input required). By targeting only applications that require lower processing performance, we can select smaller devices and components than systems with higher performance processors.
This reference design implements a reinforced isolated three-phase inverter subsystem using isolated IGBT gate drivers and isolated current/voltage sensors. The UCC23513 gate driver used is available in a 6-pin wide body package and LED light analog input, and can be used as a pin-for-pin replacement for existing optically isolated gate drivers. This design shows that the UCC23513 input stage can be driven using all existing configurations for driving optoisolated gate drivers. In-phase shunt resistor based motor current sensing is implemented using the AMC1300B isolated amplifier and DC link voltage, and IGBT module temperature sensing is implemented using the AMC1311 isolated amplifier. This design uses the C2000™ LaunchPad™ to control the inverter.
The SimpleLink™ Multi-Standard CC2650 Remote Control Reference Design is an all-in-one solution for the development of voice-based Bluetooth® Low Energy, ZigBee® RF4CE™ or multi-standard remote control. This reference design shows the recommended decoupling and RF layout for optimal RF performance. This design uses discrete components for the balun and filter, as well as an inverted F-shaped PCB antenna to provide good performance at low cost.
84 W isolated flyback power supply for chargers and adapters using PowiGaN-based InnoSwitch3-CP (INN3279C-H218)
This PMP10600.1 reference design provides all the power rails required to power the Xilinx® Zynq® 7000 Series (XC7Z015) FPGA. This design uses multiple LMZ3 series modules, multiple LDOs, and a DDR termination regulator. It also has an LM3880 for power-up and power-down sequencing. This design uses a 12V input voltage.
Power-over-Ethernet (PoE) technology enables power-sourcing equipment (PSE, a switch/router or midspan system) to deliver up to 15W of power to IEEE® 802.3af-compliant powered devices like IP phones and wireless LAN access points. This application note describes how to design a single-port PSE system to meet the IEEE 802.3af signature, classification, and power-management requirements. The single-port PSE in this example is designed using the MAX5922A IC.
Active Balance chipset used in large lithium-ion batteries provides monitoring, balancing and communication functions. With precise and reliable active balancing, Active Balance BMS enables bidirectional power transfer within each cell. Each EM1401EVM can manage 6 to 14 cells (up to 60V) in Li-ion battery applications. EM1401EVM modules can be stacked up to 1300V. The system provides fast cell balancing, diagnostic functions and modules for controller communication. An independent protection circuit is also provided.
60 W USB PD 3.0 with PPS charger (5 V/3 A; 9 V/3 A; 15 V/3 A; 20 V/3 A; 3.3 V-21 V PPS outputs) using InnoSwitch3-Pro (INN3379C-H302) and Weltrend (WT6635P) USB PD controller
The design converts an 8V-42V DC input into a 5.1V output and is protected by the TPS2546-Q1 programmable current protection switch. Its handshake protocol enables fast charging of smartphones/tablets/handheld devices. By detecting the load current and adjusting the DC/DC output voltage, this design can implement linear USB cable differential compensation function to keep the USB port voltage within a limited range. This design is suitable for devices such as vehicle-mounted hosts and remote USB hubs.
This reference design is a power supply optimized specifically for powering eight 16-channel receive AFE ICs in ultrasound imaging systems. This design uses a single-chip DC/DC converter + LDO combo regulator to set each LDO input just above the dropout voltage while fully utilizing the LDO PSRR, thereby reducing parts count while maximizing efficiency. In addition, ultra-low noise LDOs help achieve the highest possible analog-to-digital conversion resolution, resulting in higher image quality. The design's ability to synchronize the switching frequency with the master clock frequency and the system clock frequency allows system designers to apply simple filtering techniques to eliminate power switching noise on ground loops or use spread spectrum clocking to reduce EMI. Additionally, the design implements an electronic fuse device, providing a simple and flexible method of overcurrent protection.
This processor-based reference design helps speed time to market and helps customers design cost-effective human-machine interface (HMI) solutions for electric vehicle (EV) charging infrastructure or EV power supply equipment (EVSE). This reference design demonstrates the two-dimensional (2D) Qt graphical user interface (GUI) common to EVSE HMI, as well as TI processor capabilities for software-rendered graphics. The AM335x processors provide scalability and a variety of processing speeds and compatible software to meet the needs of low-end to high-end applications. They also provide ample connectivity, including key peripherals required for EVSE HMI such as universal asynchronous receiver/transmitter (UART) and CAN).
The KITPF8100FRDMEVM and KITPF8200FRDMEVM are customer evaluation boards using the PF8100 and PF8200 power management ICs.
The TIDA-00705 is an ultra-compact (1”x1”x1”) high-efficiency bidirectional DC to DC power converter capable of delivering 480W for low energy storage (LES) and battery backup power applications. Specifically, it is designed for server battery backup Unit (BBU) embedded server PSU. The reference design is based on a two-phase spaced half-bridge power stage controlled using the UCD3138 digital power stage controller. The design has built-in DC bus overcurrent, overvoltage protection and battery overcurrent, overvoltage protection. Voltage protection and phase current balancing to dissipate heat.
Kinetic Digits is a mechanical flipping digital display, consisting of 448 7-segment digital tubes, simulating the effect of water flow. For various effects, it can be produced with the help of the provided host computer.
The ASL5115EVBMST is the main evaluation board for NXP's Matrix LED Controller (MLC) ASL5115SHN, which enables evaluation of external lighting systems.
EEWorld
subscription
account
EEWorld
service
account
Automotive
development
community
Robot
development
community
About Us Customer Service Contact Information Datasheet Sitemap LatestNews
Room 1530, 15th Floor, Building B,
No.18 Zhongguancun Street,
Haidian District,
Beijing, Postal Code: 100190
China
Telephone: 008610 8235 0740
京公网安备 11010802033920号
