FU-68PDF-V510M123B datasheet, PDF

Datasheet> All Categories > LED optoelectronic/LED> FU-68PDF-V510M123B

FU-68PDF-V510M123B: DescriptionFIBER OPTIC TRANSMITTER,MODULE-BF; CategoryLED optoelectronic/LED; File Size93KB，5 Pages; ManufacturerMitsubishi; Websitehttp://www.mitsubishielectric.com/semiconductors/

Download Datasheet Parametric View All

FU-68PDF-V510M123B Overview

FIBER OPTIC TRANSMITTER,MODULE-BF

FU-68PDF-V510M123B Parametric

Parameter Name	Attribute value
state	ACTIVE-UNCONFIRMED
Optoelectronic device type	OPTOELECTRONIC EQUIPMENT

Preview

Download Datasheet

View All

MITSUBISHI (OPTICAL DEVICES)

FU-68PDF-V510MxxxB

1.58

m (L-Band) DFB-LD MODULE WITH POLARIZATION MAINTAINING FIBER PIGTAIL

(WAVELENGTH SELECTED, BIAS CIRCUIT INTEGRATED, DIGITAL APPLICATION)

DESCRIPTION

Module type FU-68PDF-V510MxxB is a 1.58µm

(L-Band) DFB-LD module with polarization

maintaining optical fiber.

This module is suitable to a CW light source for

external modulator for use in 2.5Gb/s and 10Gb/s

digital optical communication systems.

This module is prepared to expand the wavelength

channels into L-Band for Dense-WDM transmission.

FEATURES

Input impedance is 25Ω

Multi quantum wells (MQW) DFB Laser Diode

module

Emission wavelength is in 1.58µm band

Polarization maintaining optical fiber pig-tail

Built-in optical isolator

Built-in thermal electric cooler

Butterfly package

With photodiode for optical output monitor

APPLICATION

High speed transmission systems (~10Gb/s)

Dense-WDM systems

OPTION

Wavelength option:

1565nm~1625nm are available

ABSOLUTE MAXIMUM RATINGS

(Tld=Tset)

Parameter

Symbol

Conditions

Rating

Unit

Laser diode

Optical output

power

Forward current

150

Reverse voltage

Vrl

Photodiode

Reverse voltage

Vrd

Forward current

Ifd

Thermo-

Cooler current

Ipe

1.3

electric cooler Cooler voltage

Vpe

3.1

(Note)

Operating case temperature

-20 ~ 70

Storage temperature

Tstg

-40 ~ 85

Note) Even if the thermo-electric cooler (TEC) is operated within the rated conditions, uncontrolled current

loading or operation without heatsink may easily damage the module by exceeding the storage

temperature range. Thermistor resistance should be properly monitored by the feedback circuit during TEC

operation to avoid the catastrophic damage.

Recommended Resources

Toshiba launches new three-phase brushless motor control pre-drive IC, do you know about it?

2Y-2Y-2Y connection three-speed motor contactor control circuit

Introduction to single tube mosquito killer lamp circuit

CB950 control terminal application circuit diagram a

Electrical equipment contact current detection circuit

OR circuit composed of diodes and resistors C=A+B

"【TGF4042 Signal Generator】" Potential Compensation Test: A signal generator is used to perform compensation test of signal potential. In some high-interference test situations, sometimes some low-frequency or DC signal interference may occur, causing the de...; fine0406 Test/Measurement

Popularization of basic knowledge of AC: AC contactors use main contacts to open and close circuits and auxiliary contacts to execute control instructions. The main contacts usually have only normally open contacts, while the auxiliary conta...; eeleader-mcu Industrial Control Electronics

All the experts come in and have a look: When measuring the offset current of the op amp, the circuit below is very stable, but at this time, if I connect a wire to the in-phase or inverting terminal of the first op amp, it will self-excite....; xupeilinhong Analog electronics

Please help me check out the functions of these two programs: #include "reg52.H"#define P1_0 =P1^0;#define Fosc=11059200; Unsigned char idata a(10) at 0x30; Unsigned char i,j,k; Unsigned longbb; Unsigned int xx; Void Timer0_int(void) interrupt 1{P1_0=~P1_0;TI=0;...; hjy3721 51mcu

Help with HT microcontroller uart problem: I would like to ask if anyone has used the UART port of the HT microcontroller, do you have any examples or source code? Please send it to my email fjchen_ok@126.com. I am currently working on using t...; chen_elppa Embedded System

Protel DXP signal layer management issues: When using Protel DXP to manage PCB layers, I found that in the PCB generated by the wizard or template, except for the top and buttom layers, no matter how I set it, there will always be at least 8 M...; daqiic Embedded System

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components