and cost over surface mount crystals, and increase
reliability by eliminating three or four mechanical
devices from the board.
MicroClock offers many other parts with stereo
codec support. The MK1430 has 5 output clocks,
the MK1448 has 7, the MK1444 has eight
including DSP clocks, and the MK1450/1 offers
Pentium™ and SCSI support, plus the stereo
codec clocks.
Features
• Packaged in 8 pin SOIC
• Input crystal or clock frequency of 14.318 MHz
• MK1418 is clock input only
• MK1420 output clock frequencies of 16.934MHz,
24.576 MHz, 33.868 MHz, and 14.318 MHz
• Advanced, low power CMOS process
• Lowest jitter in industry for best audio
performance
• Insensitive to input clock duty cycle
• 50% (typ) 14.318 MHz duty cycle with crystal
AC Coupling/Portable Applications
For applications in portable computers, it is possible
to drive the input clock with a 3.3V, 14.318MHz
clock by a.c. coupling using a 0.01µF capacitor
connected in series to the CLKIN pin. But the
operating VDD on pin 2 must be 5V±10%. This
technique is also effective if the input clock doesn’t
meet the VIH and VIL specifications on page 3.
Additional Clocks or Features
If more than these four output clocks or features
such as power down are needed, MicroClock has
many other products in development. Consult
MicroClock for your specific needs.
Block Diagram
VDD GND
Output
Buffer
14.318 MHz
crystal or clock
X1
Crystal
Oscillator
X2
16.934 MHz
24.576 MHz
33.868 MHz
(MK1420 only)
14.318 MHz
(MK1420 only)
Clock Synthesis
Circuitry
Output
Buffer
Output
Buffer
Output
Buffer
1
Revision 013098
Printed 11/15/00
MicroClock Division of ICS•1271 Parkmoor Ave.•San Jose•CA•95126•(408)295-9800tel•(408)295-9818fax
MDS 1418/20 A
MK1418/MK1420
OPL3, OPL4 + Codec Clock Source
Pin Assignments
MK1418
ICLK
VDD
GND
16.9M
1
2
3
4
8
7
6
5
GND
VDD
GND
24.6M
V
0.1µF
14.318 MHz
crystal
Suggested Layout
for MK1420
clock only
Pin 1
2
3
8
7
33Ω (optional)
14.3MHz out
6
33Ω (optional)
33.9MHz out
MK1420
X1
VDD
GND
16.9M
1
2
3
4
8
7
6
5
X2
14.3M
33.9M
24.6M
G
4
5
33Ω (optional)
33Ω (optional)
16.9MHz out
24.6MHz out
Pin Descriptions for MK1420
Number
1
2
3
4
5
6
7
8
Name
X1
VDD
GND
16.9M
24.6M
33.9M
14.3M
X2
Type
I
P
P
O
O
O
O
O
Description
Crystal Connection. Connect to a 14.318 MHz crystal or clock.
Connect to +5V.
Connect to ground.
16.9344 MHz clock output for stereo codec.
24.576 MHz clock output for stereo codec.
33.868 MHz clock output for OPL4.
14.318 MHz clock buffered output for OPL3 or PCMCIA controller.
Crystal Connection to a 14.318 MHz crystal, or leave unconnected for clock input.
Key: I = Input, O = output, P = power supply connection
External Components/Crystal Selection
A minimum number of external components are required for proper oscillation. For a crystal input, one
22pF load capacitor should be connected to each of the X1 and X2 pins and ground, and a parallel
resonant 14.318 MHz, 16pF load, crystal is recommended. Values near these are acceptable, as is a series
resonant crystal, but either will result in frequencies which are slightly (up to 0.06%) different from the
ideal. For a clock input, connect to X1 and leave X2 unconnected. A decoupling capacitor of 0.1µF should
be connected between VDD and GND, and 33Ω terminating resistors may be used on the clock outputs.
These terminating resistors are unnecessary for clock traces less than 1” (25mm).
2
Revision 013098
Printed 11/15/00
MicroClock Division of ICS•1271 Parkmoor Ave.•San Jose•CA•95126•(408)295-9800tel•(408)295-9818fax
MDS 1418/20 A
MK1418/MK1420
OPL3, OPL4 + Codec Clock Source
Electrical Specifications
Parameter
Supply Voltage, VDD
Inputs
Clock Outputs
Ambient Operating Temperature
Soldering Temperature
Storage temperature
Operating Voltage, VDD
Input High Voltage, VIH
Input Low Voltage, VIL
Output High Voltage, VOH
Output High Voltage, VOH
Output Low Voltage, VOL
Operating Supply Current, IDD
Input Capacitance
Actual Mean Frequency versus Target
Conditions
Referenced to GND
Referenced to GND
Referenced to GND
Max of 20 seconds
-65
4.5
3.5
IOH=-4mA
IOH=-25mA
IOL=25mA
No Load
Outputs
14.31818
Time above 2.5V
0.8 to 2.0V
2.0 to 0.8V
Time above 1.5V
Time above 1.5V
Time above 1.5V
Time above 1.5V
Pins 4, 5, 6 only
Pins 4, 5, 6 only
20
80
1.5
1.5
60
55
55
55
400
VDD-0.4
2.4
0.4
18
7
±0.2
Minimum
Typical
Maximum
7
VDD+.5V
VDD+.5V
70
260
150
5.5
2.5
2.5
1.5
Units
V
V
V
°C
°C
°C
V
V
V
V
V
V
mA
pF
%
MHz
%
ns
ns
%
%
%
%
ps
ps
ABSOLUTE MAXIMUM RATINGS (note 1)
-0.5
-0.5
0
DC CHARACTERISTICS (at 5.0V unless otherwise noted)
AC CHARACTERISTICS
Input Clock or Crystal Frequency
Input Clock Duty Cycle, 14.318MHz
Output Clock Rise Time
Output Clock Fall Time
Output Clock Duty Cycle, 24.576MHz
Output Clock Duty Cycle, 16.9344 MHz
Output Clock Duty Cycle, 33.868MHz
Output Clock Duty Cycle, 14.318 MHz, Note 3
Absolute Clock Period Jitter, except 14.3
One Sigma Clock Period Jitter, except 14.3
40
45
45
45
-400
45
50
50
50
200
60
Notes:
1. Stresses beyond those listed under Absolute Maximum Ratings could cause permanent damage to the device. Prolonged exposure
to levels above the operating limits but below the Absolute Maximums may affect device reliability.
2. Typical values are at 25°C.
3. If crystal is used as input with C
L
= 16pf. If a clock is used as input, the duty cycle of the 14.318MHz output will be the same as the
input clock.
3
Revision 013098
Printed 11/15/00
MicroClock Division of ICS•1271 Parkmoor Ave.•San Jose•CA•95126•(408)295-9800tel•(408)295-9818fax
MDS 1418/20 A
MK1418/MK1420
OPL3, OPL4 + Codec Clock Source
Package Outline and Package Dimensions
8 pin SOIC
Symbol
A
b
D
E
H
e
h
Q
L
Inches
Min
Max
0.055 0.061
0.013 0.019
0.185 0.200
0.150 0.160
0.225 0.245
.050 BSC
0.015
0.004
0.01
0.016 0.035
Millimeters
Min
Max
1.397 1.5494
0.330
0.483
4.699
5.080
3.810
4.064
5.715
6.223
1.27 BSC
0.381
0.102
0.254
0.406
0.889
E
Pin 1
H
D
Q
e
b
c
h x 45°
A
L
Ordering Information
Part/Order Number
MK1418S
MK1418STR
MK1420S
MK1420STR
Marking
MK1418S
MK1418S
MK1420S
MK1420S
Package
8 pin SOIC
Add tape and reel
8 pin SOIC
Add tape and reel
Temperature
0-70°C
0-70°C
0-70°C
0-70°C
While the information presented herein has been checked for both accuracy and reliability, MicroClock Incorporated assumes no responsibility for either its use or for the
infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in
normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements
are not recommended without additional processing by MicroClock. MicroClock reserves the right to change any circuitry or specifications without notice. MicroClock does not
authorize or warrant any MicroClock product for use in life support devices or critical medical instruments.
1201BO.7
4
Revision 013098
Printed 11/15/00
MicroClock Division of ICS•1271 Parkmoor Ave.•San Jose•CA•95126•(408)295-9800tel•(408)295-9818fax
[align=left]Hello experts, I am analyzing the [font=新宋体]micokit-enjoy[/font] project in the [font=新宋体]SDK_MiCOKit_v2.3.0.2[/font] software package of Qingke, and I have found the following program:[/a...
After positioning the STP model in PCBLIB, how can I lock the STP position to prevent it from being moved in the PCB? I have aligned the pins with the pads, how can I lock the position between them? I...
Rockchip launches RK2808 chip solution for 720p playback under Android. Fuzhou Rockchip, the strongest domestic chip solution manufacturer, has just launched the RK2808 chip solution, which is a chip ...
Dear experts, when I do the CAN1 loopback test, I can send and receive data normally; but when I change to normal mode, I cannot send and receive; CAN2 loopback mode and normal mode cannot send and re...
Abstract: The demand for dynamic power management in embedded systems is analyzed , and on this basis, a system-level dynamic power management architecture based on a policy framework is proposed to a...
Gesture sensor
1. The difference between attitude sensor, gyroscope, acceleration, angular velocity and geomagnetic sensor
2. The difference between 3-axis, 6-axis and 9-axis gyroscopes...
In the past few days, the news that ZTE was "banned" by the US Department of Commerce has triggered widespread reflection and concern in various domestic industries about the lack of independent co...[Details]
"Originally, there are many people who can design very good
chips
, but the market does not give domestic
chips
the opportunity to iterate, and domestic companies cannot give engine...[Details]
Friends who work in the photovoltaic industry, do you still remember the hard work on June 30 last year? How many people worked late into the night for months in a row just to connect to the grid a...[Details]
At present, in the world,
the construction of
smart cities
is in the process of gradually landing from concept, and technology giants and investment giants are important participants in this...[Details]
This small program is still the use of timer, which is relatively simple. The specific parts are noted in the comments, please refer to the comments. /*********************************************...[Details]
The implementation of CAN driver under embedded operating system Android requires not only adding CAN driver device in Linux kernel, but also implementing the call of Android HAL layer. Taking S5...[Details]
1. Heart rate measurement principle 1. What is a heart rate module? The heart rate module is professionally used to monitor the heart rate of the wrist, fingers, forehead, earlobe, chest and other ...[Details]
In mid-to-late 2016, a girl from Hubei came to Beijing alone, full of curiosity about
cloud computing
. The girl left the deepest impression on me was her lovely smile. She told me that if ...[Details]
Ouster LiDAR OS-1 (left) and OS-2 (center) Velodyne invented the modern 3D LiDAR scanner in the mid-2000s, but in recent years conventional wisdom has held that Velodyne’s design — 64 lasers mounted...[Details]
Table of contents: 1 Overview 2: Common interrupt functions 3: PWM output 1 Overview In development, timers are widely used, which can be simply summarized into three aspects: 1.1: Application of ...[Details]
Using AT89S51 microcontroller, modify the original one to turn the LED on for 4s and off for 2s. Thank you. Use a timer. (The program is written in the answer, omitted here - just a note) The origi...[Details]
Try to design a subroutine, whose function is to rearrange the 6 single-byte positive integers in the internal RAM pointed to by (R0) in ascending order. ;========================================== ...[Details]
DIY/Open Source Hardware
京公网安备 11010802033920号
EEWORLD
