Standard Resistance Range.........................................................................................................................................................200 to 100 K ohms
Total Resistance Tolerance.................................................................................................................................................................................±5 %
Absolute Minimum Resistance ...................................................................................................... 1 ohm or 0.1 % maximum (whichever is greater)
Noise ................................................................................................................................................................................. 100 ohms ENR maximum
Dielectric Withstanding Voltage (MIL-STD-202, Method 301)
Power Rating (Voltage Limited By Power Dissipation or 450 VAC, Whichever is Less)
+40 °C ..........................................................................................................................................................................................................2 watts
+125 °C ......................................................................................................................................................................................................... 0 watt
Resolution.............................................................................................................................................................. See recommended part numbers
Operating Temperature Range .......................................................................................................................................................-40 °C to +125 °C
Storage Temperature Range ..........................................................................................................................................................-55 °C to +125 °C
Temperature Coefficient Over Storage Temperature Range
Vibration ............................................................................................................................................................................................................. 15 G
Wiper Bounce .................................................................................................................................................................0.1 millisecond maximum
Shock.................................................................................................................................................................................................................. 50 G
Wiper Bounce .................................................................................................................................................................0.1 millisecond maximum
Load Life .....................................................................................................................................................................................1,000 hours, 2 watts
Total Resistance Shift .................................................................................................................................................................... ±2 % maximum
Rotational Life (No Load).................................................................................................................................................1,000,000 shaft revolutions
Total Resistance Shift .................................................................................................................................................................... ±5 % maximum
Moisture Resistance (MIL-STD-202, Method 103, Condition B)
Total Resistance Shift .................................................................................................................................................................... ±2 % maximum
IP Rating
Sealed Versions (-3, -4, -7, and -8) .................................................................................................................................................................IP 65
Unsealed Versions (-1 -2, -5, and -6) ..............................................................................................................................................................IP 40
Shaft Runout.......................................................................................................................................................................0.13 mm (0.005 in.) T.I.R.
Lateral Runout ....................................................................................................................................................................0.20 mm (0.008 in.) T.I.R.
Shaft End Play ....................................................................................................................................................................0.25 mm (0.010 in.) T.I.R.
Shaft Radial Play ................................................................................................................................................................0.13 mm (0.005 in.) T.I.R.
Pilot Diameter Runout ........................................................................................................................................................0.08 mm (0.003 in.) T.I.R.
Backlash ............................................................................................................................................................................................. 1.0 ° maximum
Weight ........................................................................................................................................................................................ Approximately 19 G
Terminals ................................................................................................................................................................................ Solder lugs or PC pins
Soldering Condition
Manual Soldering............................................96.5Sn/3.0Ag/0.5Cu solid wire or no-clean rosin cored wire; 370 °C (700 °F) max. for 3 seconds
Wave Soldering .....................................................................96.5Sn/3.0Ag/0.5Cu solder with no-clean flux; 260 °C (500 °F) max. for 5 seconds
Wash processes ....................................................................................................................................................................... Not recommended
Marking ......................Manufacturer’s name and part number, resistance value and tolerance, linearity tolerance, wiring diagram, and date code.
Ganging (Multiple Section Potentiometers) .......................................................................................................................................1 cup maximum
Hardware ............................................................................................. One lockwasher and one mounting nut is shipped with each potentiometer.
NOTE: For Anti-rotation pin add 91 after configuration dash number. Example: -2 becomes -291 to add AR pin.
1
At room ambient: +25 °C nominal and 50 % relative humidity nominal, except as noted.
2
Consult manufacturer for complete specification details for resistances below 1k ohms.
*RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific disclaimers as set forth on the last page of this document, and at www.bourns.com/legal/disclaimer.pdf.
Ro VE LEA
HS RS D
C ION FRE
OM S E
PL AR
IA E
NT
*
5.08 ± .38
(.200 ± .015)
1
2
5.08 ± .38
(.200 ± .015)
6.99 ± .38
(.275 ± .015)
10.31 +.00/-.10
(.406 +.000/-.004)
3
*SEE
NOTE
.76 ± .25
R
.030 ± .010
.81
(.032)
SHAFT DIA. (SEE
PART NUMBERS)
BUSHING DIA. (SEE
PART NUMBERS)
.81 ± .25
(.032 ± .010)
20.63 ± .81
(.812 ± .032)
3590 - Precision Potentiometer
Product Dimensions
18.59 ± .38
(.732 ± .015)
.25
(.010)
7.93
(.312)
5.08 ± .38
(.200 ± .015)
-1, -3, -5, -7 Configurations
-2, -4, -6, -8 Configurations
6.99 ± .38
5.08 (.275 ± .015)
± .38
5.08 ± .38
5.08 ± .38
10.31 +.00/-.10
(.200 ± .015)
(.200 ± .015)
(.200 ± .015)
5.08 ± .38
(.406 +.000/-.004)
6.99 ± .38
5.08 ± .38
12.2
15.54
3
*SEE
(.200 ± .015)
6.99 ± .38
(.275 ± .015)
.76 ± .25
1
NOTE
(.200 ± .015)
5.08 ± .38
(.480)
R
(.612)
5.08 ± .38
(.275 ± .015)
.030
10.31 +.00/-.10 ± .010
2
6.99 ± .38
10.31 + .00/- .13
R MAX.
(.200 ± .015)
(.200 ± .015)
(.406 +.000/-.004) .81
(.275 ± .015)
(.406+.000/-.005)
3
*SEE
10.31 + .00/- .13
3
(.032)
.76 ± .25
1
NOTE
BUSHING DIAMETER
1
11.81
R
(.406+.000/-.005)
*SEE
.030 ± .010
(SEE PART NUMBERS)
2
(.465)
NOTE
2
BUSHING DIAMETER
1
.81
3
.81
SHAFT DIA. (SEE
(SEE PART NUMBERS)
(.032)
(.032)
2
.25
12.70 ±0.25
PART NUMBERS)
DIA.
.81
(.010)
(.500 ± .010)
DIA.
22.22 ± .38
BUSHING DIA. (SEE
(.032)
MOUNTING SURFACE
PART NUMBERS)
SHAFT DIAMETER (.875 ±.015)
SHAFT DIA. (SEE
.81 ± .25 NUMBERS)
.25
5.08 ± .38
.25
(SEE PART NUMBERS)
PART
(.032 ± .010)
(.010)
7.93
(.010)
(.200 ± .015)
SHAFT DIAMETER
1.19
BUSHING DIA. (SEE
.25
(SEE PART NUMBERS)
(.312)
5.08 ± .38
PART NUMBERS)
(.047)
6.99 ± .38
7.92
*BUSHING THREAD SPECIFICATIONS:
20.63 ± .81
18.59 ± .38
(.010)
(.200 ± .015)
.81 ± .25
1.19
-1, -2, -3, -4 .... 3/8-32 UNF
(.275 ± .015)
(.312)
(.812 ± .032)
(.732 ± .015)
10.31 +
± .38
.13
(.032 ± .010)
7.93
(.047)
-5, -6, -7, -8 .... M9 x 0.75-7H
5.08
.00/-
20.62 ± .81
7.92
18.6 ± .4
(.406+.000/-.005)
(.312)
(.200 ± .015)
(.312)
(.812 ± .032)
(.732 ± .015)
20.63 ± .81
18.59 ± .38
5.08 ± .38
BUSHING DIAMETER
1
3
20.62 ± .81
18.6 ± .4 PART
6.99 ± .38
(.812 ± .032)
(.732 ± .015)
(.200 ± .015)
(SEE
NUMBERS)
2
(.812 ±
(.732 ± .015) .81
(.275 ± .015)
10.31 + .00/- .13
.032)
12.2
12.2
15.54
(.032)
(.48)
(.406+.000/-.005)
15.54
(.480)
BUSHING DIAMETER
(.612)
1
R MAX.
3
(.612)
(SEE PART
12.2
NUMBERS)
R MAX.
2
.81
(.48)
SHAFT DIAMETER
15.54
12.2
15.54
MAX.
.25
(SEE PART
R
NUMBERS)
(.032)
11.81
(.612)
(.480) 11.81
(.612)
(.010)
(.465)
1.19
(.465)
R MAX.
(.047)
SHAFT DIAMETER
11.81
7.92
12.70
PART NUMBERS)
22.22 ± .38
.25
12.70 ±0.25
(SEE
DIA.
DIA.
(.465)
DIA.
(.312)
11.81
(.500)
(.875 ±.015)
(.010)
(.500 ± .010)
DIA.
22.22 ± .38
1.19
(.465)
20.62 ± .81
18.6 ± .4
MOUNTING SURFACE
MOUNTING SURFACE
(.875 ±.015)
12.70
22.22 ± .38
7.92
(.812 ± .032)
DIA.
(.047)
(.732 ± .015)
DIA.
12.70 ±0.25
(.312)
(.500)
(.875
MOUNTING HOLE LOCATIONS
DIA.
RECOMMENDED PC BOARD
±.015)
(.500 ± .010)
DIA.
20.62 ± .81
18.6 ± .4
22.22 ± .38
MOUNTING SURFACE
HOLE DIAMETER
FMS
(.812 ± .032)
(.732 ± .015)
12.2
PC PIN
(.875 ±.015)
12.19 ± 0.51
MOUNTING SURFACE
Recommended PCB Layout
Terminal Styles
*BUSHING THREAD SPECIFICATIONS:
TERMINAL
2.08
RECOMMENDED PC BOARD MOUNTING HOLE LOCATIONS
(.480 ± .020)
(.48)
(.082)
-1, -2, -3, -4 .... 3/8-32 UNF
15.54
THICKNESS
CCW
CW
R MAX.
HOLE DIAMETER
“P” Terminal
1.63 ± 0.38
-6, -7, -8 .... M9 x 0.75-7H
Style
-5,
12.2
FMS
.305 ± .003
(.612)
2
1
3
PC PIN
2.08
12.19 ± 0.51
(.064 ± .015)
(.48)
(.012 ± .0001)
*BUSHING THREAD SPECIFICATIONS:
TERMINAL
15.54
(.082)
(.480 ± .020)
R MAX.
-1, -2, -3, -4 .... 3/8-32 UNF
CCW
CW
11.81
CW
THICKNESS
(.612)
1.63 ± 0.38
-5, -6, -7, -8 .... M9 x 0.75-7H
.305 ± .003
(.465)
2
1
3
5.08 5.08 6.99
(.064 ± .015)
11.81
(.012 ± .0001)
(.275)
(.200) (.200)
(.465)
12.70
CW
22.22 ± .38
3.30 ± 0.38
DIA.
DIA.
(.500) 5.08 6.99
(.875 ±.015)
TOLERANCES: EXCEPT WHERE NOTED
5.08
(.130 ± .015)
12.70
22.22 ± .38
.508
MOUNTING
.127
SURFACE
(.200)
DECIMALS: .XX
±.015)
DIA.
(.200) (.275)
(.500)
DIA.
(.875
± (.02), .XXX ± (.005)
3.30 ± 0.38
RECOMMENDED PC
FRACTIONS: ±1/64
HOLE LOCATIONS
MOUNTING SURFACE
BOARD MOUNTING
TOLERANCES: EXCEPT WHERE NOTED
(.130 ± .015)
Schematic
HOLE DIAMETER
DIMENSIONS: MM
PC BOARD MOUNTING HOLE LOCATIONS
RECOMMENDED
.508
.127
FMS
DECIMALS: .XX ±
.XXX ±
(IN.)
2.08
HOLE DIAMETER
(.005)
FMS
(.02),
(.082)
2.08
FRACTIONS: ±1/64
CCW
CW
(.082)
MM
CCW
CW
DIMENSIONS:
2
1
3
(IN.)
“S” Terminal Style
2
1
3
12.19 ± 0.51
CW
(.480 ± .020)
CW
5.08 5.08 6.99
2.54
5.08 5.08 6.99
(.200) (.200) (.275)
(.100) 12.19 ± 0.51
(.200) (.200) (.275)
(.480 ± .020)
3 PLCS.
SOLDER LUG
TOLERANCES: EXCEPT WHERE NOTED
TOLERANCES: EXCEPT WHERE NOTED
2.54
TERMINAL
.508
.127
.508
.127
DECIMALS: .XX ±
.XXX ±
0.86 (.100)
(.02),
DECIMALS: .XX ± (.02), .XXX ± (.005)
(.005)
SOLDER LUG
(.034) 3 PLCS.
FRACTIONS: ±1/64
FRACTIONS: ±1/64
TERMINAL
3 PLCS.
MM
MM
DIMENSIONS:
DIMENSIONS:
(IN.)
0.86
(IN.)
(.034)
3 PLCS.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific disclaimers as set forth on the last page of this document, and at www.bourns.com/legal/disclaimer.pdf.
3590 - Precision Potentiometer
Recommended Part Numbers
(Printed Circuit)
3590P-2-102L
3590P-2-202L
3590P-2-502L
3590P-2-103L
3590P-2-203L
3590P-2-503L
3590P-2-104L
(Solder Lug)
3590S-2-102L
3590S-2-202L
3590S-2-502L
3590S-2-103L
3590S-2-203L
3590S-2-503L
3590S-2-104L
(Solder Lug)
3590S-1-102L
3590S-1-202L
3590S-1-502L
3590S-1-103L
3590S-1-203L
3590S-1-503L
3590S-1-104L
Resistance (Ω)
1,000
2,000
5,000
10,000
20,000
50,000
100,000
Resolution (%)
.029
.023
.025
.020
.019
.013
.009
BOLDFACE
LISTINGS ARE IN STOCK AND READILY AVAILABLE
THROUGH DISTRIBUTION. FOR OTHER OPTIONS CONSULT FACTORY.
ROHS IDENTIFIER:
L = COMPLIANT
Panel Thickness Dimensions
(For Bushing Mount Only)
2.46 - 3.81
(.097 - .150)
Shaft & Bushing Configurations
(Bushing - DxL, Shaft - D):
(-1) Plastic Bushing (3/8 ” x 5/16 ”) and
Shaft (.2480 + .001, - .002)
PANEL
(-2) Metal Bushing (3/8 ” x 5/16 ”) and
Shaft (.2497 + .0000, - .0009)
(-3) Sealed, Plastic Bushing (3/8 ” x 5/16 ”) and
Shaft (.2480 + .001, - .002)
(-4) Sealed, Metal Bushing (3/8 ” x 5/16 ”) and
Shaft (.2497 + .0000, - .0009)
(-5) Metric, Plastic Bushing (9 mm x 7.94 mm) and
Shaft (6 mm + 0, - .076 mm)
(-6) Metric, Metal Bushing (9 mm x 7.94 mm) and
Shaft (6 mm + 0, - .023 mm)
HEX NUT
LOCKWASHER
POT
(-7) Metric, Sealed, Plastic Bushing (9 mm x 7.94 mm) and
Shaft (6 mm + 0, - .076 mm)
(-8) Metric, Sealed, Metal Bushing (9 mm x 7.94 mm) and
Shaft (6 mm + 0, - .023 mm)
10.44 ± .07
DIA.
(.411 ± .003)
R
7.42
(.292)
ADDITIONAL HOLE FOR
ANTI-ROTATION PIN
1.60 +.08/-.03
DIA.
(.063 +.003/-.001)
Anti-rotation pin hole is shown at six o'clock
position for reference only. The actual location is
determined by the customer's application. Refer
to the front view of the potentiometer to see the
location of the optional A/R pin.
Panel thickness and hole diameters are
recommended for best fit. However, customers
may adjust the dimensions to suit their specific
application.
DIMENSIONS:
MM
(INCHES)
TOLERANCES: ±
0.127
(.005)
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific disclaimers as set forth on the last page of this document, and at www.bourns.com/legal/disclaimer.pdf.
REV. 11/17
Legal Disclaimer Notice
This legal disclaimer applies to purchasers and users of Bourns
®
products manufactured by or on behalf of Bourns, Inc. and
its affiliates (collectively, “Bourns”).
Unless otherwise expressly indicated in writing, Bourns
®
products and data sheets relating thereto are subject to change
without notice. Users should check for and obtain the latest relevant information before placing orders and should verify that
such information is current and complete.
The characteristics and parameters of a Bourns
®
product set forth in its data sheet are based on laboratory conditions, and
statements regarding the suitability of products for certain types of applications are based on Bourns’ knowledge of typical
requirements in generic applications. The characteristics and parameters of a Bourns
®
product in a user application may vary
from the data sheet characteristics and parameters due to a combination of the Bourns
®
product with other components in
the user’s application or due to the environment of the user application itself. Such characteristics and parameters also can
and do vary in different applications and actual performance may vary over time. Users should always verify actual performance
of the Bourns
®
product in their specific devices and applications, and make their own independent judgments about how
much additional test margin to design in to compensate for differences between laboratory and real world conditions.
Unless Bourns has explicitly designated an individual Bourns
®
product as meeting the requirements of a particular industry
standard (e.g., ISO/TS 16949) or a particular qualification (e.g., UL listed or recognized), Bourns is not responsible for any
failure of an individual Bourns
®
product to meet requirements of such industry standard or such particular qualification. Users
of Bourns
®
products are responsible for ensuring compliance with safety-related requirements and standards applicable to
their applications.
Bourns
®
products are not recommended, authorized or intended for use in nuclear, lifesaving, life-critical or life-sustaining
applications, nor in any other applications where failure or malfunction may result in personal injury, death, or severe property
or environmental damage. Unless expressly and specifically approved in writing by two authorized Bourns representatives on
a case-by-case basis, use of any Bourns
®
products in such unauthorized applications is at the user’s sole risk. Life-critical
applications include devices identified by the U.S. Food and Drug Administration as Class III devices and generally equivalent
classifications outside of the United States.
Bourns
®
standard products that are designed and tested for use in automotive applications will be described on the applicable
data sheets as compliant with the applicable AEC-Q standard. Unless expressly and specifically approved in writing by two
authorized Bourns representatives on a case-by-case basis, use of any other Bourns
®
standard products in an automotive
application is not recommended, authorized or intended and will be at the user’s sole risk.
Bourns
®
standard products are not tested to comply with United States Federal Aviation Administration standards generally
or any other generally equivalent governmental organization standard applicable to products designed or manufactured for
use in aircraft or space applications. Bourns
®
standard products that are designed and tested for use in aircraft or space
applications will be described on the applicable data sheets as compliant with the RTCA DO-160 standard. Unless expressly
and specifically approved in writing by two authorized Bourns representatives on a case-by-case basis, use of any other
Bourns
®
standard product in an aircraft or space application is not recommended, authorized or intended and will be at the
user’s sole risk.
The use and level of testing applicable to Bourns
®
custom products shall be negotiated on a case-by-case basis by Bourns
and the user for which such Bourns
®
custom products are specially designed. Absent a written agreement between Bourns
and the user regarding the use and level of such testing, the provisions above applicable to Bourns
®
standard products shall
also apply to such Bourns
®
custom products.
Users shall not sell, transfer, export or re-export any Bourns
®
products or technology for use in activities which involve the
design, development, production, use or stockpiling of nuclear, chemical or biological weapons or missiles, nor shall they use
Bourns
®
products or technology in any facility which engages in activities relating to such devices. The foregoing restrictions
apply to all uses and applications that violate national or international prohibitions, including embargos or international
regulations. Further, Bourns
®
products, technology or technical data may not under any circumstance be exported or
re-exported to countries subject to international sanctions or embargoes, and Bourns
®
products may not, without prior
authorization from Bourns and/or the U.S. Government, be resold, transferred, or re-exported to any party not eligible to
receive U.S. commodities, software, and technical data.
To the maximum extent permitted by applicable law, Bourns disclaims (i) any and all liability arising out of the application or
use of any Bourns
®
standard product, (ii) any and all liability, including, without limitation, special, punitive, consequential
or incidental damages, and (iii) any and all implied warranties, including implied warranties of fitness for particular purpose,
non-infringement and merchantability.
For your convenience, copies of this Legal Disclaimer Notice with German, Spanish, Japanese, Traditional Chinese and Simplified Chinese
Magnetrons have been widely used in radar, navigation, communication, industrial heating, medical treatment, food industry and other fields due to their advantages of small size, light weight, low wor...
[i=s]This post was last edited by liwenz on 2016-9-1 22:40[/i] I need to display inout variables in simulation, but I don’t know how to display them. In .v, it is like this: assign usbdata = usbdir?8'...
Reflow soldering is a critical process in electronics assembly production, and the cleanliness of the reflow oven has a direct impact on product quality. Dust and residue accumulation within the ov...[Details]
Abstract:
With the increasing complexity of smart vehicle electrical and electronic architectures, the full lifecycle management of vehicle electronic control components faces multiple challe...[Details]
When we travel in cities, we all find that electric vehicles have many advantages. As a means of transportation, they can also fulfill their mission well. Now, more and more residential communities...[Details]
Since the beginning of this year, price wars have intensified, new models have been launched one after another, used cars with zero kilometers have become a hot topic, and the industry's internal c...[Details]
Have you ever heard stories about "crazy appliances"? Think of microwaves that turn on automatically or ovens that preheat without any human input? With radios and electromagnetic interfaces ubiqui...[Details]
While the current industry consensus is that autonomous vehicles are robots and that their systems are managed using robotics-developed thinking, there are also cases where autonomous driving is ac...[Details]
A human-machine interface (HMI) refers to the platform used by people to operate a PLC. This platform provides an interface between programs and humans, serving as a medium for information transmis...[Details]
As the power density of modern electronic systems continues to increase, effective thermal management has become critical to ensuring system performance, reliability, and longevity—especially in hi...[Details]
With the continuous development of ultrasonic technology, ultrasound has been widely used in fields such as inspection, cleaning, welding, and medical treatment, and has even found its way into tex...[Details]
The practice of warming up a car originated with gasoline-powered vehicles. Warming up the engine allows it to enter a better working state and ensures good lubrication. This has become a habit for...[Details]
According to foreign media reports, German chipmaker Infineon has recently completed the acquisition of Marvell Technology's automotive Ethernet business for a total transaction amount of US$2.5 bi...[Details]
It’s a collaborative blueprint designed to address integration complexities and create scalable solutions through Arm’s automotive innovation ecosystem.
The transformation of future mo...[Details]
Siemens software mainly includes PLC, frequency converter, human-machine interface, etc. The current Siemens software can be said to be very stable.
PLC series range from the Siemens S5 series...[Details]
New energy electric vehicles are energy-saving, environmentally friendly, have low operating costs, and enjoy strong support from national policies. With the growth in sales of new energy electric ...[Details]
introduction
Commercial air conditioner PCBs involve both high-voltage and low-voltage power. The power supply for commercial air conditioners often passes through the controller. This forces ...[Details]
DIY/Open Source Hardware
京公网安备 11010802033920号
EEWORLD
