Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional opera-
tion of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
Continuous Power Dissipation (T
A
= +70NC)
TSSOP (derate 26.1mW/
o
C above +70NC) .......... 2088.8mW*
TQFN (derate 28.6mW/
o
C above +70NC) ............ 2285.7mW*
Operating Temperature Range ........................ -40NC to +125NC
Junction Temperature .....................................................+150NC
Storage Temperature Range............................ -65NC to +150NC
Lead Temperature (soldering, 10s) ................................+300NC
Soldering Temperature (reflow) ..................................... +260
o
C
PACKAGE THERMAL CHARACTERISTICS (Note 1)
TSSOP
Junction-to-Ambient Thermal Resistance (B
JA
) .......38.3NC/W
Junction-to-Case Thermal Resistance (B
JC
) .................3NC/W
TQFN
Junction-to-Ambient Thermal Resistance (B
JA
) ..........35NC/W
Junction-to-Case Thermal Resistance(B
JC
) ...............2.7NC/W
Note 1:
Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer
board. For detailed information on package thermal considerations, refer to
www.maximintegrated.com/thermal-tutorial.
ELECTRICAL CHARACTERISTICS
(V
SUP
= V
SUPSW
= 14V, V
EN
= 14V, C
BIAS
= 1FF, R
FOSC
= 12kI, T
A
= T
J
= -40NC to +125NC, unless otherwise noted. Typical values
are at T
A
= +25NC.)
PARAMETER
Supply Voltage Range
Load-Dump Event Supply
Voltage
SYMBOL
V
SUP
,
V
SUPSW
V
SUP_LD
I
SUP
Supply Current
t
LD
< 1s
I
LOAD
= 1.5A
Standby mode, no load, V
OUT
= 5V
I
SUP_STANDBY
Standby mode, no load, V
OUT
= 5V, T
A
= +25°C
I
SHDN
V
BIAS
V
UVBIAS
V
EN
= 0V
V
SUP
= V
SUPSW
= 6V to 36V
V
BIAS
rising
4.7
2.9
3.5
30
30
5
5
3.1
400
+175
15
60
45
12
5.3
3.3
FA
FA
V
V
mV
NC
NC
CONDITIONS
MIN
3.5
TYP
MAX
36
42
UNITS
V
V
mA
Shutdown Supply Current
BIAS Regulator Voltage
BIAS Undervoltage Lockout
BIAS Undervoltage-Lockout
Hysteresis
Thermal-Shutdown Threshold
Thermal-Shutdown Threshold
Hysteresis
Maxim Integrated
*The
parametric values (min, typ, max limits) shown in the Electrical Characteristics table supersede values quoted elsewhere in this data sheet.
2
MAX16907
36V, 2.2MHz Step-Down Converter
with Low Operating Current
ELECTRICAL CHARACTERISTICS* (continued)
(V
SUP
= V
SUPSW
= 14V, V
EN
= 14V, C
BIAS
= 1FF, R
FOSC
= 12kI, T
A
= T
J
= -40NC to +125NC, unless otherwise noted. Typical values
are at T
A
= +25NC.)
PARAMETER
OUTPUT VOLTAGE (OUT)
Output Voltage
Skip-Mode Output Voltage
Adjustable Output Voltage
Range
Load Regulation
Line Regulation
BST Input Current
LX Current Limit
Skip-Mode Threshold
Spread Spectrum
Power-Switch On-Resistance
High-Side Switch Leakage
Current
TRANSCONDUCTANCE AMPLIFIER (COMP)
FB Input Current
I
FB
FB connected to an external resistive
divider, 0°C < T
A
< +125°C
-40°C < T
A
< +125°C
6V < V
SUP
< 36V
V
FB
= 1V, V
BIAS
= 5V (Note 2)
0.99
0.985
10
1.0
1.0
0.02
900
80
f
SW
= 2.2MHz
f
SW
= 1MHz
R
FOSC
= 12kI
T
A
= +25°C
t
FSYNC
(Note 2)
f
OSC
+
10%
1
2.05
98
99
2.20
2.35
1.01
1.015
%/V
FS
ns
%
nA
R
ON
I
BST_ON
I
LX
I
SKIP_TH
Spread spectrum enabled
R
ON
measured between SUPSW and LX,
I
LX
= 1A, V
BIAS
= 5V
V
SUP
= 36V, V
LX
= 0V, T
A
= +25°C
V
OUT
V
OUT_SKIP
V
OUT_ADJ
V
FB
= V
BIAS,
normal operation
No load, V
FB
= V
BIAS
FB connected to external resistive divider
V
FB
= V
BIAS
, 30mA < I
LOAD
< 3A
V
FB
= V
BIAS
, 6V < V
SUPSW
< 36V
High-side on, V
BST
- V
LX
= 5V
(Note 2)
3.4
4.925
4.925
1
0.5
0.02
1.5
4.1
300
6
70
150
1
2.5
6
5
5
5.075
5.15
10
V
V
V
%
%/V
mA
A
mA
%
mI
FA
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
FB Regulation Voltage
V
FB
V
FB Line Regulation
Transconductance (from FB to
COMP)
Minimum On-Time
Maximum Duty Cycle
OSCILLATOR FREQUENCY
Oscillator Frequency
EXTERNAL CLOCK INPUT (FSYNC)
FSYNC Input Current
External Input Clock Acquisition
Time
External Input Clock Frequency
DV
LINE
g
m
t
ON_MIN
DC
MAX
MHz
1
FA
Cycles
Hz
Maxim Integrated
*The
parametric values (min, typ, max limits) shown in the Electrical Characteristics table supersede values quoted elsewhere in this data sheet.
3
MAX16907
36V, 2.2MHz Step-Down Converter
with Low Operating Current
ELECTRICAL CHARACTERISTICS* (continued)
(V
SUP
= V
SUPSW
= 14V, V
EN
= 14V, C
BIAS
= 1FF, R
FOSC
= 12kI, T
A
= T
J
= -40NC to +125NC, unless otherwise noted. Typical values
are at T
A
= +25NC.)
PARAMETER
External Input Clock
High Threshold
External Input Clock
Low Threshold
Soft-Start Time
ENABLE INPUT (EN)
Enable Input-High Threshold
Enable Input-Low Threshold
Enable Threshold Voltage
Hysteresis
Enable Input Current
RESET
Output Overvoltage Trip
Threshold
PGOOD
Switching Level
PGOOD
Debounce
PGOOD
Output Low Voltage
PGOOD
Leakage Current
I
SINK
= 5mA
V
OUT
in regulation, T
A
= +25NC
V
OUT_OV
V
TH_RISING
V
TH_FALLING
V
FB
rising, V
PGOOD
= high
V
FB
falling, V
PGOOD
= low
105
93
90
10
110
95
92.5
35
115
97
95
60
0.4
1
%V
FB
%V
FB
Fs
V
FA
V
EN_HI
V
EN_LO
V
EN,HYS
I
EN
T
A
= +25°C
0.2
1
2
0.9
V
V
V
FA
SYMBOL
V
FSYNC_HI
V
FSYNC_LO
t
SS
V
FSYNC
rising
V
FSYNC
falling
8.5
CONDITIONS
MIN
1.4
0.4
TYP
MAX
UNITS
V
V
ms
Note 2:
Guaranteed by design; not production tested.
Maxim Integrated
*The
parametric values (min, typ, max limits) shown in the Electrical Characteristics table supersede values quoted elsewhere in this data sheet.
I believe everyone has noticed that the advertising section is too crazy... It seems to have the most posts in all the sections, but it doesn't seem to be very meaningful. How much advertising effect ...
Why does the address of Samsung 4510b have a base address? 3ff0000 #define SFR_BASE 0x3FF8000 #define INTPND (*((volatile unsigned long *) (SFR_BASE + 0x4004))) The manual says INTPND is 0x4004. In ad...
[i=s]This post was last edited by Tobey on 2017-3-22 12:10[/i] My roommate and I wrote a simple LED flipping program. When the sensing area is touched, the LED state is flipped. Since the LED output l...
1. Several nouns
ABI:
The specifications that an executable file must follow in order to run in a specific execution environment;
Separately generated relocatabl...[Details]
EtherCAT (Ethernet for Control Automation Technology) is a real-time industrial fieldbus communication protocol based on an Ethernet-based development framework. EtherCAT is one of the fastest indu...[Details]
1. Project Overview
1.1 Introduction
Currently, most music files are saved in MP3 format, a lossy audio compression format that cannot perfectly reproduce the original music. With the exp...[Details]
Whether it is an electric car or an ordinary fuel car, for the vast majority of car buyers, the final cost of use is what they care about most. For fuel cars, how to save fuel is what drivers care ...[Details]
Is pure electric vehicles a false proposition for long-distance driving? At least from my personal perspective, based on current technological and infrastructure standards, I believe so. Below, I'l...[Details]
Topics: Bring Your Own Device (BYOD) trends; the impact of using employees' own mobile devices to control access to work facilities and equipment on information security; and ways to securely imple...[Details]
Definition of interactive projection system:
Interactive projection systems, also known as multimedia interactive projection, are available in floor, wall, and tabletop interactive projection....[Details]
Common Mode Semiconductor has officially released its latest generation of power management ICs—the GM6506 series. This fully integrated high-frequency synchronous rectification step-down p...[Details]
introduction
The concept of the smart home is gradually developing and gaining market acceptance. We believe its ultimate form lies in the interconnection of all home appliances through open i...[Details]
As AI accelerates across industries, the demand for data center infrastructure is also growing rapidly.
Keysight Technologies, in collaboration with Heavy Reading, released the "Beyo...[Details]
With the rapid development of electric vehicles in my country, people are beginning to pay attention to the issue of radiation from electric vehicles. We all know that mobile phones emit radiation,...[Details]
Permanent magnets are essential components in a wide range of household and industrial devices. They are particularly crucial in the renewable energy sector, including electric vehicle motors. Curr...[Details]
Recently, Joyson Electronics has made positive progress in the core technology research and development of the robot's "brain and brain" and key components, and launched the industry's first integr...[Details]
To improve the lateral active safety of intelligent connected vehicles, the identification and definition of unexpected functional safety scenarios for the EPS (Electronic Steering System) ...[Details]
Methods of DC motor speed regulation:
1. The voltage regulator can be used to change the input voltage and speed directly, which is often used for large kilowatt-level motors.
2. Thyristo...[Details]
Microchip MCU
京公网安备 11010802033920号
EEWORLD
