Range (Note 4).........................................T
C
= -40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Note 1:
Based on junction temperature T
J
= T
C
+ (θ
JC
x V
CC
x I
CC
). This formula can be used when the temperature of the exposed
pad is known while the device is soldered down to a PCB. See the
Applications Information
section for details. The junction
temperature must not exceed +150°C.
Note 2:
Junction temperature T
J
= T
A
+ (θ
JA
x V
CC
x I
CC
). This formula can be used when the ambient temperature of the PCB is
known. The junction temperature must not exceed +150°C.
Note 3:
Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-
layer board. For detailed information on package thermal considerations, refer to
www.maxim-ic.com/thermal-tutorial.
Note 4:
T
C
is the temperature on the exposed pad of the package. T
A
is the ambient temperature of the device and PCB.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
5.0V SUPPLY DC ELECTRICAL CHARACTERISTICS
(Typical
Application Circuit,
V
CC
= 4.75V to 5.25V, no input AC signals. T
C
= -40°C to +85°C, unless otherwise noted. Typical values
are at V
CC
= 5.0V, T
C
= +25°C, all parameters are production tested.)
PARAMETER
Supply Voltage
Supply Current
SYMBOL
V
CC
I
CC
CONDITIONS
MIN
4.75
TYP
5.0
230
MAX
5.25
245
UNITS
V
mA
3.3V SUPPLY DC ELECTRICAL CHARACTERISTICS
(Typical
Application Circuit,
V
CC
= 3.0V to 3.6V, no input AC signals. T
C
= -40°C to +85°C, unless otherwise noted. Typical values are
at V
CC
= 3.3V, T
C
= +25°C, parameters are guaranteed by design and not production tested, unless otherwise noted.)
I was lucky to get this PELCO dome camera! A friend sent it to me for repair. It was heavy and substantial when I first got it. It really looked like an American Hummer! It turned out that the dome ca...
[align=left][font=楷体,楷体_GB2312]In terms of principle, aluminum batteries are actually very old-fashioned, just like carbon-zinc batteries. However, without graphene, the power of aluminum cannot be fu...
When using the Hezongda development board, I checked the execution efficiency of C language and found that it was very low.Take the timer interrupt as an example (Hezongda development board sample pro...
I asked a friend to help me download this for your reference. I hope you will have a systematic understanding of digital oscilloscopes after reading it: [b]The development and reasonable selection of ...
On a PDA, after installing a CAB package, you can usually uninstall a previously installed CAB software in the "remove programs" tool provided by the system. I would like to ask: Does WINCE provide th...
Chapter 36 DHT11 Digital Temperature and Humidity Sensor Experiment, In the previous chapter, we introduced the use of the digital temperature sensor DS18B20. In this chapter, we will introduce the us...
This program is written to simulate the serial port hardware mechanism. When used, a timed interrupt can be set with a time interval of 1/4 baud rate. The receiving function is called once for ea...[Details]
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
1 Introduction
The high temperature tester is mainly used for temperature tracking measurement and data acquisition during the heating process. By systematically analyzing the test data, the...[Details]
The Portable Digital Data Acquisition System (PDDAS) uses LabVIEW Real-Time and PXI to control the wind tunnel test and record air pressure data from 128 different channels.
"The LabVIEW Real-...[Details]
No matter which processor you are learning, the first thing you need to understand is the registers and working mode of the processor.
ARM has 37 registers, including 31 general registers and ...[Details]
DSP (digital signal processor) is used more and more frequently in today's engineering applications. There are three main reasons for this: first, it has powerful computing power and is capable of ...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
Power management solutions for today's portable application processors are becoming increasingly integrated. Total power consumption, standby and sleep current consumption affect battery size, bill...[Details]
My colleague and I spent the day chatting in the hotel bar. We had met with several customers. We were both wondering how come these engineers we were meeting knew almost nothing about analog techn...[Details]
A standard cell
is an electrochemical
cell
used as a voltage reference standard in many electrical standards laboratories
. If properly maintained, standard cells are very stable. The ...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
General LED lighting has a current limiting resistor in the driving circuit, and the power consumed by the resistor has nothing to do with the LED light emission. In order to improve efficiency, a...[Details]
In the analysis of electronic circuits, static analysis (also known as DC analysis) is the basis of circuit analysis. However, it is well known that electronic components are nonlinear, so the anal...[Details]
RS-422 and RS-485 are both serial data interface standards, which were developed and published by the Electronic Industries Association (EIA). RS-422 defines a balanced communication interface with a ...[Details]
Describe how to meet the challenges of complexity with a modern wiring design toolset. Option codes and expressions can simulate the variables of an automotive project. A full-featured tool suite c...[Details]
Industrial Control Electronics
京公网安备 11010802033920号
EEWORLD
