EEWORLDEEWORLDEEWORLD

Part Number

Search

CMH11006815G

Description
Metal Film Resistors - Through Hole
CategoryPassive components   
File Size1MB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

CMH11006815G Online Shopping

Suppliers Part Number Price MOQ In stock  
CMH11006815G - - View Buy Now

CMH11006815G Overview

Metal Film Resistors - Through Hole

CMH11006815G Parametric

Parameter NameAttribute value
Product CategoryMetal Film Resistors - Through Hole
ManufacturerTT Electronics plc
Resistors
Thick Film High Voltage/
Thick Film High
MIL-Approved
High Reliability
Voltage/
High Reliability MIL-Approved
Metal Glaze™ Resistors
CMH Series
Diamond spiraled
thick film element
Heat conducting
ceramic substrate
Metal Glaze™ Resistors
1/4 watt to 5 watt
TCR of ±100 ppm/°C
TCR of ±100 ppm/°C
PRF
Qualified to MIL-R-49462
330K ohm to 1G ohm range
330K ohm to 1G ohm range
±1%, ±2%, or ±5% tolerance
±1%, ±2%, or ±5% tolerance
Epoxy coated body
Diamond spiraled
thick film element
Heat conducting
ceramic substrate
CMH Series
High conductivity plated on
nickel termination
All welded cap and lead construction
Tin Lead electroplated leads
Epoxy coated body
High conductivity plated on
nickel termination
All welded cap and lead construction
Tin Lead electroplated leads
Electrical Data
IRC Type
CMH - 1/4
CMH - 1/2
CMH - 1
CMH - 2
CMH - 3
CMH - 5
MIL
Type³
RHV30
RHV31
RHV32
RHV33
RHV34
RHV35
Power
Rating @
70°C (watts)¹
1/4
1/2
1
2
3
5
Voltage
Rating
(volts)²
750
1,500
3,000
5,000
10,000
20,000
Resistance Range
(ohms)
4
330K - 100M
330K - 392M
330K - 499M
330K - 499M
330K - 1000M
330K - 1000M
1, 2, 5
100
0 to -5
Tolerance
(±%)
Maximum
TCR
(±ppm/°C)
4
VCR (ppm/V)
Notes:
1. For power rating above 70C, see derating curve.
2. Voltage rating shown is the rated DC continuous working voltage or the sine-wave RMS absolute maximum voltage at com-
mercial line frequency.
3. Marked per MIL-PRF-49462
4. Values greater than 100 meg and less than 500 meg, ±200ppm; values greater than or equal to 500 meg, ±500ppm.
Environmental Data
Test Condition*
Thermal Shock
Solder Effect
Terminal Strength
Moisture Resistance
Load Life (1000 Hours at 25°C)
Shelf Life (1 year at 25°C)
Low-Temperature Operation
Shock
Vibration
Dielectric Strength
Insulation Resistance at 500 VDC
Notes:
*Test per MIL-PRF-49462 and MIL-STD-202
General Note
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
Maximum
∆R
(±3σ)
±0.25%
±0.15%
±0.20%
±0.50%
±1.00%
±0.10%
±0.15%
±0.35%
±0.35%
±0.15%
±10
9
min
Typical
∆R
±0.10%
±0.05%
±0.10%
±0.20%
±0.25%
±0.03%
±0.05%
±0.10%
±0.10%
±0.05%
5 x 10
12
typ
BI Technologies IRC Welwyn
CMH Series Issue September 2008 Sheet 1 of 3
All information is subject to TT Electronics’ own data and is considered accurate at time of going to print.
Wire and Film Technologies Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
www.ttelectronics.com/resistors
A subsidiary of
TT electronics plc
© TT Electronics plc
11.17
Band switch and answer b08liuq friend
[size=3]Early mechanical band switches were mostly used in radios for band switching, hence the name. Currently, in many (even most) fields, this type of mechanical band switch has been replaced by so...
njdyp Analog electronics
Show the process of WEBENCH design + op amp dual power supply generation circuit
1. Enter the TI design homepage to set parameters, as follows, two voltage outputs2. Select the power IC for design3. View the BOM table of the entire power system4. View the design chart5. View the d...
常见泽1 Analogue and Mixed Signal
Regarding the LM2596 conversion circuit problem, the output cannot be output
[font=微软雅黑]12V to 5V output, used a multimeter to test, 12V input, but no 5V output, all components are within the specifications, I don't know why, it's my first time doing this, I don't understand, ...
岁风月 Power technology
I would like to ask if the 8255A chip can only select one port at a time. After defining the address for the port, such as Q8255A XBYTE...
I would like to ask if the 8255A chip can only select one port at a time. After defining the address for the port, such as Q8255A XBYTE[0x1CFF], if you want to use port A in the program, you can direc...
一脸懵逼 51mcu
What do you think of TI's lithium battery AFE chip bq76940?
Some time ago, I saw that TI has released a new series of lithium battery AFE chips, the bq76940 series. Is there anyone in the forum planning to adopt it?...
Study_Stellaris Analogue and Mixed Signal
InstaSpin FOC question
When InstaSpin FOC uses an estimator to identify the motor stator resistance Rs, the TI user guide says to inject DC current into the D axis. Why is the phase current waveform given in the user guide ...
喜鹊王子 TI Technology Forum

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2867  1122  2002  2539  2837  58  23  41  52  4 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号