Option “K” is designed and tested for use with printed circuit boards or ring/fork terminals having a thickness between 0.031 and 0.093 inches (0.79 to 2.36 mm), and loads rated up to 50
Amps. For higher load currents, the “K” standoff temperature must not exceed 105°C. For additional application assistance please contact Crydom Technical Support.
(3)
Output will self trigger between 450-600Vpk, Min., not suitable for capacitive loads.
(4)
Instantaneous turn-on version is not recomended for capacitive loads. Use zero turn-on only.
(5)
All parameters at 25°C unless otherwise specified.
(6)
Heat sinking required, see derating curves.
(7)
For 40mA minimum current, the voltage drop increases over maximum rated.
(8)
Maximum turn-on voltage for -B option is: 1VDC for DC control, 10Vrms for AC control, and 4Vrms for E control range.
(9)
For relays with option “G” minimum control voltage is 4.5VDC.
(10)
Must turn-off voltage for -B option is: 3VDC for DC control, 90Vrms for AC control, and 18Vrms for E control range.
(11)
Turn-on time for Instantaneous turn-on versions is 0.02 msec (DC Control Models).
(12)
All parameters at 50% power rating and 100% duty cycle (contact Crydom tech support for detailed report).
(13)
Load can be wired to either SSR output terminal 1 or 2.
(14)
Elective Input Status LED, “G” option.
(15)
Elective Overvoltage Protection, “P” option.
(16)
Mechanical dimensions vary from G3 models.
For additional information or specific questions, contact Crydom Technical Support.
New evidence in humans shows that the typical Western diet, which is high in fat and sugar "junk food," can quickly disrupt the brain's control over appetite.After a week of gorging on waffles, milksh...
I want to use a single chip microcomputer to generate a PWM waveform to control the dimming of an LED. How should I design the LED driving circuit? Is there a circuit composed of a better chip? Please...
I was recently writing about LPC2132 IIC and encountered a problem.1. Use Zhougong IIC package, no problem, sometimes it works fine and sometimes not.2. Reading and writing in query mode will failwhil...
I just got started with FPGA. Now I need to make a dynamic reconfiguration and use two FPGAs to implement dynamic switching between two algorithms, that is, to use one to control the other to achieve ...
From 2007 to 2012, the annual compound growth rate of the MEMS market will reach 14%. In order to meet market demand, MEMS companies and foundries are improving their production and manufacturing leve...
I have just started to use ARM7. I have done experiments with 80C51 before. Now I am looking at the user guide of LPC1114 and I find it difficult. I don't know how to set it up. For example,
In the fl...
Emergency hand-held lamps powered by 6V maintenance-free batteries are widely used in rural areas. The charger used is a transformer step-down and single diode half-wave rectifier, and the charging...[Details]
1 Introduction
A wide variety of communication cables and control cables are widely used in various instruments and control equipment. Whether the cable is well-conducted and
whether
th...[Details]
In this article, the high-performance DSP developed by TI can be used as an effective confidentiality method if it is applied to PC encryption cards.
As an effective network security solution,...[Details]
In the previous series, we have listed some basic knowledge of C language in Tables 1 to 3. We hope that beginners can strengthen their memory of the above tables and gradually learn to use them wh...[Details]
Vertical cavity surface emitting lasers (VCSELs) are gradually replacing traditional edge emitting lasers, especially in low bandwidth and short-distance communication systems where cost factors ar...[Details]
Aromatic gases are widely present in food, medicine, cosmetics and various daily chemical products, such as snacks, liquor, spices, Chinese herbal medicines, plasters, perfumes, soaps, shampoos, et...[Details]
Contact resistance
is the resistance to current flow through a closed pair of contacts. This type of measurement is performed on devices such as connectors,
relays
, and switches. The...[Details]
I. Introduction
Since RS232 has a short communication distance (only 15 meters according to EAT/TAI-232 standard), and can only perform point-to-point communication, it cannot directly f...[Details]
1 Introduction
Building Automation System (BAS) is a distributed monitoring system (DCS) designed according to distributed information and control theory. It is the result of the mutual de...[Details]
1 Introduction
With the development of control, computer, communication, network technology, etc., a new control technology, namely fieldbus, has emerged in the field of industrial control...[Details]
1. Introduction to CIF Board
Fieldbus integration based on PC system
Whether it is a master or a slave, fieldbus has won unanimous praise in the field of PC-based automation. For more...[Details]
1 Introduction to HART Protocol
HART (Highway Addressable Remote Transducer), an open communication protocol for addressable remote sensor high-speed channels, was launched by Rosemen in the U...[Details]
MediaTek (2454) announced the acquisition of F-MStar (3697) and attracted the attention of IC design industry. This morning, Gartner Semiconductor Industry Research Director Hong Cenwei analyzed ...[Details]
Digital array radar (DAR) uses digital beam forming (DBF) in both receiving and transmitting modes to achieve flexible distribution and reception of RF signal power in the airspace, obtain excellent t...[Details]
TC9012F is a universal CMOS large-scale integrated circuit for infrared remote control signal transmission, suitable for remote control of TV, VTR, laser player and other equipment. In the market, ...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
