835-13-034-10-001000 datasheet, PDF

Datasheet> All Categories > The connector> The connector> 835-13-034-10-001000

835-13-034-10-001000: DescriptionBoard Connector, 34 Contact(s), 2 Row(s), Female, Straight, Solder Terminal, Socket, ROHS COMPLIANT; CategoryThe connector The connector; File Size167KB，1 Pages; ManufacturerMill-Max; Websitehttps://www.mill-max.com; Environmental Compliance

Download Datasheet Parametric View All

835-13-034-10-001000 Overview

Board Connector, 34 Contact(s), 2 Row(s), Female, Straight, Solder Terminal, Socket, ROHS COMPLIANT

835-13-034-10-001000 Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	Mill-Max
package instruction	ROHS COMPLIANT
Reach Compliance Code	compliant
Body/casing type	SOCKET
Connector type	BOARD CONNECTOR
Contact to complete cooperation	GOLD (30) OVER NICKEL (100)
Contact completed and terminated	GOLD (10)
Contact point gender	FEMALE
Contact material	NOT SPECIFIED
DIN compliance	NO
Filter function	NO
IEC compliance	NO
JESD-609 code	e4
MIL compliance	NO
Manufacturer's serial number	835
Mixed contacts	NO
Installation method	STRAIGHT
Installation type	BOARD
Number of rows loaded	2
Options	GENERAL PURPOSE
Terminal pitch	2.54 mm
Termination type	SOLDER
Total number of contacts	34
Base Number Matches	1

Preview

Download Datasheet

View All

INTERCONNECTS

OFP® Pass Thru Sockets for Ø.030” &

Single and Double Row

•

834/835 Series Pass Thru Sockets have a low

.130” profile and will accept Ø.030” round pin,

as well as industry standard .025” square pin

headers.

•

They are typically used to interconnect two or

more parallel circuit boards.

•

Sockets are designed for hand, wave or reflow*

soldering. The high temp. insulator is compati-

ble with all solder processes.

•

Unique

ORGANIC FIBRE PLUG®

barriers pre-

vent solder, paste or flux from contaminating

the internal spring contacts. After soldering, the

OFP®

barriers are pushed out of the socket

when the mating header is inserted.

•

Mill-Max sockets use a precision machined

brass sleeve with a press-fit beryllium copper

“multi-finger” spring contact.

•

Recommended mounting holes are Ø.046

±.003” PTH (1,2 mm drilled prior to plating).

*Intrusive reflow (also called "pin-in-paste") is a tech-

nique of using conventional thru-hole components

in a reflow soldering process. The pass thru socket

is placed into plated-thru-holes in the circuit board

(solder paste has previously been screen printed on

pads adjacent to the holes) and the board is

reflowed in the same pass as other SMT compo-

nents. Solder will fill the plated-thru-holes and

achieve solder joints as reliable as wave soldering.

The OFP® barrier prevents solder paste from being

picked-up inside the contact during assembly.

Series 834, 835

.025” pins

Typical Application

US Patent #7,086,870

Ordering Information

Single Row

OFP® Pass Thru Socket

834-XX-0 _ _-10-001000

01-64

Fig. 1

Specify # of pins

Fig. 1

Double Row OFP® Pass Thru Socket

835-XX-0 _ _-10-001000

Fig. 2

Specify # of pins

For RoHS compliance

select plating code.

SPECIFY PLATING CODE XX=

02-72

XX= Plating Code

See Below

30µ” Au

Sleeve (Pin)

10µ” Au 200µ” Sn/Pb 200µ”Sn/Pb 200µ”Sn 200µ”Sn

200µ”Sn/Pb 30µ” Au 200µ”Sn

Fig. 2

Contact (Clip)

w w w. m i l l - m a x . c o m

516-922-6000

Recommended Resources

Y-△ started motor automatic mutual switching circuit a

Temperature measurement circuit using silicon transistors as sensors

Optical signal receiver circuit diagram

SCR pre-regulator circuit suitable for any power supply

Proportional thermostat circuit

Computer motherboard circuit diagram 810 3_14

Preliminary analysis of the G problem of the electronic competition: For reference only I am moving house recently and all the instruments and equipment have been packed, so there is no actual testing and debugging. This plan is for reference only. I made this transcei...; RF-刘海石 Electronics Design Contest

Does JLINK support STM8 simulation download?: Does stvd support JLINK emulation? If so, how should it be set up?...; boesdt stm32/stm8

About DM9000AE eboot driver (wince): Is there an eboot driver for DM9000AE? Can you send me one? When I am debugging the bootloader, I find that the Probe fails and the network card chip cannot be found. The light on the board is not on....; losng Embedded System

Newbie's question!! First aid, about CCS loading .out problem: I use two boards controlled by Zhongda F28016 brushless motor. When I think I am ready, I load the .out file with CCS3.3, and the error " data verification failed at address 0x3F8000 please verify tar...; shesay Microcontroller MCU

【Reprint】One-click access ASUS M4A89GTD pro/USB3.0: After the 785G was launched, all manufacturers have done their best to develop a method that allows users to open the core more conveniently. This time, we got the newly launched AMD 890GX chipset ASU...; chengj Embedded System

Question: What does (+ 30 absolute ) mean after IAR for MSP compilation?: MSP430 80bytes of DATA memory (+ 30 absolute ) + 30 absolute? What does it mean? 102 bytes of DATA memory (+ 30 bytes shared) + 30 bytes shared??? What does it mean?...; hanskying666 Microcontroller MCU

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components