DATASHEET
EL7202, EL7212, EL7222
High Speed, Dual Channel Power MOSFET Drivers
The EL7202, EL7212, EL7222 ICs are matched dual-drivers
that improve the operation of the industry standard DS0026
clock drivers. The Elantec versions are very high speed
drivers capable of delivering peak currents of 2.0 amps into
highly capacitive loads. The high speed performance is
achieved by means of a proprietary “Turbo-Driver” circuit
that speeds up input stages by tapping the wider voltage
swing at the output. Improved speed and drive capability are
enhanced by matched rise and fall delay times. These
matched delays maintain the integrity of input-to-output
pulse-widths to reduce timing errors and clock skew
problems. This improved performance is accompanied by a
10 fold reduction in supply currents over bipolar drivers, yet
without the delay time problems commonly associated with
CMOS devices. Dynamic switching losses are minimized
with non-overlapped drive techniques.
FN7282
Rev.2.01
Feb 18, 2020
Features
• Industry standard driver replacement
• Improved response times
• Matched rise and fall times
• Reduced clock skew
• Low output impedance
• Low input capacitance
• High noise immunity
• Improved clocking rate
• Low supply current
• Wide operating voltage range
• Pb-Free available (RoHS compliant)
Pinouts
EL7212
(8-PIN PDIP, SO)
TOP VIEW
EL7222
(8-PIN PDIP, SO)
TOP VIEW
Applications
• Clock/line drivers
• CCD Drivers
• Ultra-sound transducer drivers
• Power MOSFET drivers
• Switch mode power supplies
• Class D switching amplifiers
INVERTING
DRIVERS
COMPLEMENTARY
DRIVERS
• Ultrasonic and RF generators
• Pulsed circuits
EL7202
(8-PIN PDIP, SO)
TOP VIEW
NON-INVERTING
DRIVERS
Manufactured under U.S. Patent Nos. 5,334,883, #5,341,047
FN7282 Rev.2.01
Feb 18, 2020
Page 1 of 11
EL7202, EL7212, EL7222
Ordering Information
Part Number
EL7202CN
(No longer available,
recommended replacement:
EL7202CSZ)
EL7202CSZ
(See Note)
EL7202CSZ-T7
(See Note)
EL7202CSZ-T13 (See Note)
EL7212CNZ
EL7212CSZ
(See Note)
EL7212CSZ-T7
(See Note)
EL7212CSZ-T13
(See Note)
EL7222CSZ
(See Note)
EL7222CSZ-T7
(See Note)
EL7222CSZ-T13
(See Note)
PART MARKING
EL7202CN
TAPE & REEL
-
PACKAGE
8 Ld PDIP
PKG. DWG. #
E8.3
7202CSZ
7202CSZ
7202CSZ
EL7212CN Z
7212CSZ
7212CSZ
7212CSZ
7222CSZ
7222CSZ
7222CSZ
-
7”
13”
-
-
7”
13”
-
7”
13”
8 Ld SOIC
(Pb-free)
8 Ld SOIC
(Pb-free)
8 Ld SOIC
(Pb-free)
8 Ld PDIP*
(Pb-free)
8 Ld SOIC
(Pb-free)
8 Ld SOIC
(Pb-free)
8 Ld SOIC
(Pb-free)
8 Ld SOIC
(Pb-free)
8 Ld SOIC
(Pb-free)
8 Ld SOIC
(Pb-free)
M8.15E
M8.15E
M8.15E
E8.3
M8.15E
M8.15E
M8.15E
M8.15E
M8.15E
M8.15E
NOTE: Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish,
which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Pb-free products are MSL classified at Pb-free peak
reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
*Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications.
FN7282 Rev.2.01
Feb 18, 2020
Page 2 of 11
EL7202, EL7212, EL7222
Absolute Maximum Ratings
(T
A
= 25°C)
Supply (V+ to Gnd) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5V
Input Pins . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +0.3V above V+
Combined Peak Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . .4A
Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C
Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C
Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 125°C
Power Dissipation
SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .570mW
PDIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1050mW
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: T
J
= T
C
= T
A
DC Electrical Specifications
parameter
INPUT
V
IH
I
IH
V
IL
I
IL
V
HVS
OUTPUT
R
OH
R
OL
I
PK
I
DC
POWER SUPPLY
I
S
T
A
= 25°C, V = 15V unless otherwise specified
Description
Test Conditions
Min
Typ
Max
Units
Logic “1” Input Voltage
Logic “1” Input Current
Logic “0” Input Voltage
Logic “0” Input Current
Input Hysteresis
@0V
@V+
2.4
0.1
10
0.8
0.1
0.3
10
V
µA
V
µA
V
Pull-Up Resistance
Pull-Down Resistance
Peak Output Current
Continuous Output Current
I
OUT
= -100mA
I
OUT
= +100mA
Source
Sink
Source/Sink
100
3
4
2
2
6
6
A
mA
Power Supply Current
Inputs High/EL7202
Inputs High/EL7212
Inputs High/EL7222
4.5
4.5
1
2.5
7.5
2.5
5.0
15
mA
V
V
S
Operating Voltage
T
A
= 25°C, V = 15V unless otherwise specified
Description
Test Conditions
AC Electrical Specifications
parameter
SWITCHING CHARACTERISTICS
t
R
t
F
t
D1
t
D2
Rise Time
Fall Time
Min
Typ
Max
Units
C
L
= 500pF
C
L
= 1000pF
C
L
= 500pF
C
L
= 1000pF
See Timing Table
See Timing Table
7.5
10
10
13
18
20
ns
20
ns
20
25
25
ns
ns
Turn-On Delay Time
Turn-Off Delay Time
FN7282 Rev.2.01
Feb 18, 2020
Page 3 of 11
EL7202, EL7212, EL7222
Timing Table
Standard Test Configuration
Simplified Schematic
FN7282 Rev.2.01
Feb 18, 2020
Page 4 of 11
EL7202, EL7212, EL7222
Typical Performance Curves
MAX POWER/DERATING CURVES
SWITCH THRESHOLD vs SUPPLY VOLTAGE
INPUT CURRENT vs VOLTAGE
PEAK DRIVE vs SUPPLY VOLTAGE
QUIESCENT SUPPLY CURRENT
“ON” RESISTANCE vs
SUPPLY VOLTAGE
FN7282 Rev.2.01
Feb 18, 2020
Page 5 of 11