Contains eight flip-flops with single-rail outputs
Buffered clock and direct clear inputs
Individual data input to each flip-flop
Applications include:
- Buffer/storage registers, shift registers, and pattern
generators
1.2μ
CMOS
- Latchup immune
High speed
Low power consumption
Single 5 volt supply
Available QML Q or V processes
Flexible package
- 20-pin DIP
- 20-lead flatpack
UT54ACS273 - SMD 5962-96578
UT54ACTS273 - SMD 5962-96579
DESCRIPTION
The UT54ACS273 and the UT54ACTS273 are positive-edge-
triggered D-type flip-flops with a direct clear input.
Information at the D inputs meeting the setup time requirements
is transferred to the Q outputs on the positive-going edge of the
clock pulse. When the clock input is at either the high or low
level, the D input signal has no effect at the output.
The devices are characterized over full military temperature
range of -55°C to +125°C.
FUNCTION TABLE
INPUTS
CLR
L
H
H
H
CLK
X
↑
↑
L
D
x
X
H
L
X
OUTPUTS
PINOUTS
20-Pin DIP
Top View
CLR
1Q
1D
2D
2Q
3Q
3D
4D
4Q
V
SS
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
V
DD
8Q
8D
7D
7Q
6Q
6D
5D
5Q
CLK
20-Lead Flatpack
Top View
CLR
1Q
1D
2D
2Q
3Q
3D
4D
4Q
V
SS
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
V
DD
8Q
8D
7D
7Q
6Q
6D
5D
5Q
CLK
LOGIC SYMBOL
Q
x
L
H
L
No change
CLR
CLK
1D
2D
3D
4D
5D
6D
7D
8D
(1)
(11)
(3)
(4)
(7)
(8)
(13)
(14)
(17)
(18)
1D
R
C1
(2)
(5)
(6)
1Q
2Q
3Q
(9)
4Q
(12)
5Q
(15)
6Q
(16)
7Q
(19)
8Q
1
Note:
1. Logic symbol in accordance with ANSI/IEEE standard 91-1984
and IEC Publication 617-12.
LOGIC DIAGRAM
1D
(3)
2D
(4)
3D
(7)
4D
(8)
5D
(13)
6D
(14)
7D
(17)
8D
(18)
CLK
(11)
D
C
R
CLR
(1)
(2)
1Q
D
C
R
D
C
R
D
C
R
D
C
R
D
C
R
D
C
R
D
C
R
(5)
2Q
(6)
3Q
(9)
4Q
(12)
5Q
(15)
6Q
(16)
7Q
(19)
8Q
2
OPERATIONAL ENVIRONMENT
1
PARAMETER
Total Dose
SEU Threshold
2
SEL Threshold
Neutron Fluence
LIMIT
1.0E6
80
120
1.0E14
UNITS
rads(Si)
MeV-cm
2
/mg
MeV-cm
2
/mg
n/cm
2
Notes:
1. Logic will not latchup during radiation exposure within the limits defined in the table.
2. Device storage elements are immune to SEU affects.
ABSOLUTE MAXIMUM RATINGS
SYMBOL
V
DD
V
I/O
T
STG
T
J
T
LS
Θ
JC
I
I
P
D
PARAMETER
Supply voltage
Voltage any pin
Storage Temperature range
Maximum junction temperature
Lead temperature (soldering 5 seconds)
Thermal resistance junction to case
DC input current
Maximum power dissipation
LIMIT
-0.3 to 7.0
-.3 to V
DD
+.3
-65 to +150
+175
+300
20
±10
1
UNITS
V
V
°C
°C
°C
°C/W
mA
W
Note:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device at
these or any other conditions beyond limits indicated in the operational sections is not recommended. Exposure to absolute maximum rating conditions for extended
periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
V
IN
T
C
PARAMETER
Supply voltage
Input voltage any pin
Temperature range
LIMIT
4.5 to 5.5
0 to V
DD
-55 to + 125
UNITS
V
V
°C
3
DC ELECTRICAL CHARACTERISTICS
7
(V
DD
= 5.0V
±
10%; V
SS
= 0V
6
, -55°C < T
C
< +125°C); Unless otherwise noted, Tc is per the temperature range ordered.
SYMBOL
V
IL
PARAMETER
Low-level input voltage
1
ACTS
ACS
High-level input voltage
1
ACTS
ACS
Input leakage current
ACTS/ACS
Low-level output voltage
3
ACTS
ACS
High-level output voltage
3
ACTS
ACS
Short-circuit output current
2 ,4
ACTS/ACS
Output current
10
(Sink)
I
OH
Output current
10
(Source)
P
total
I
DDQ
ΔI
DDQ
Power dissipation
2, 8, 9
Quiescent Supply Current
Quiescent Supply Current Delta
ACTS
V
IN
= V
DD
or V
SS
I
OL
= 8.0mA
I
OL
= 100μA
I
OH
= -8.0mA
I
OH
= -100μA
V
O
= V
DD
and V
SS
V
IN
= V
DD
or V
SS
V
OL
= 0.4V
V
IN
= V
DD
or V
SS
V
OH
= V
DD
- 0.4V
C
L
= 50pF
V
DD
= 5.5V
For input under test
V
IN
= V
DD
- 2.1V
For all other inputs
V
IN
= V
DD
or V
SS
V
DD
= 5.5V
C
IN
C
OUT
Input capacitance
5
Output capacitance
5
ƒ
= 1MHz @ 0V
ƒ
= 1MHz @ 0V
15
15
pF
pF
1.9
10
1.6
mW/
MHz
μA
mA
-8
mA
.7V
DD
V
DD
- 0.25
-200
8
200
.5V
DD
.7V
DD
-1
1
CONDITION
MIN
MAX
0.8
.3V
DD
UNIT
V
V
IH
V
I
IN
V
OL
μA
0.40
0.25
V
V
OH
V
I
OS
I
OL
mA
mA
4
Notes:
1. Functional tests are conducted in accordance with MIL-STD-883 with the following input test conditions: V
IH
= V
IH
(min) + 20%, - 0%; V
IL
= V
IL
(max) + 0%, -
50%, as specified herein, for TTL, CMOS, or Schmitt compatible inputs. Devices may be tested using any input voltage within the above specified range, but are
guaranteed to V
IH
(min) and V
IL
(max).
2. Supplied as a design limit but not guaranteed or tested.
3. Per MIL-PRF-38535, for current density
≤
5.0E5 amps/cm
2
, the maximum product of load capacitance (per output buffer) times frequency should not exceed 3,765
pF/MHz.
4. Not more than one output may be shorted at a time for maximum duration of one second.
5. Capacitance measured for initial qualification and when design changes may affect the value. Capacitance is measured between the designated terminal and V
SS
at
frequency of 1MHz and a signal amplitude of 50mV rms maximum.
6. Maximum allowable relative shift equals 50mV.
7. All specifications valid for radiation dose
≤
1E6 rads(Si).
8. Power does not include power contribution of any TTL output sink current.
9. Power dissipation specified per switching output.
10. This value is guaranteed based on characterization data, but not tested.
There is a serial port class that uses event trigger mode to read data. setcommmask(hComm,ev_rxchar|ev_rxflag), another program sends data to the serial port at a certain interval, the time interval i...
I have installed Windows CE 5.0 and EVC 4.0 under Windows XP. The contents of Windows CE 5.0 include: Documentation Microsoft Windows CE 5.0 Test Platform Builder 5.0 Realease Notes Windows CE 5.0 Com...
Dear colleagues: Hello everyone! I have been thinking about opening Linuxdriver.cn for a long time, and I finally had the time to launch this community recently. Here, according to the issues that eng...
License Plate on a MIPS R4000 (revision A) processorLicense Plate on a MIPS R4400 ProcessorLicense Plates on MIPS R10000 ProcessorsLicense Plates on a MIPS R12000 Processor...
introduction
At the beginning of this century, Veit used Einthoven's galvanometer to record the electrical activity of the human pregnant uterus from the body surface for the first time. In 19...[Details]
The overcurrent and overheating coordinated protection technology implemented by polymer positive temperature coefficient devices (PPTC) can protect motors, controllers and electronic components in...[Details]
Abstract This paper
introduces a wireless radio frequency transmission chip nRF9E5 based on 8051 core. The remote control system of flapping-wing micro-aircraft is made by using this chip. Th...[Details]
Battery system architecture
For many years, nickel-cadmium batteries and later nickel-metal hydride battery technology have dominated the market. Lithium batteries have only entered ...[Details]
I hope my mobile phone has more functions, I hope my digital camera is smaller, I hope my Walkman can listen longer... Consumers are always full of expectations for the performance of portable electro...[Details]
Nowadays, video conferencing has become a situation where multiple manufacturers supply various high-definition products. The technology of high-definition products has greatly matured, the cost h...[Details]
Abstract:
A single pulse secondary radar reply processor implemented with EPLD. Its main functions include: reply frame pulse detection, reply information decoding, assembling reply inf...[Details]
Development Status
Looking at the development of security monitoring technology: from the first generation of analog monitoring, to the second generation of digital monitoring, and then up...[Details]
On July 1 this year, the "Civil Airport Management Regulations" will be officially implemented. The new regulations put forward higher requirements for the safe operation of airports. At the same t...[Details]
After being widely adopted in applications such as backlighting of portable products with small and medium-sized screens, light-emitting diodes (LEDs) have entered the field of general lighting in ...[Details]
Broadcom Corporation announced that its integrated digital TV system-on-chip (SoC) solution, the BCM3549, has been selected by LG Electronics for use in two new broadband high-definition television...[Details]
The challenge facing today's automotive electronics engineers is to build low-cost, fail-silent automotive systems that work even when they fail. Braking, steering, and other vehicle stability cont...[Details]
The ADSP-TS101-based high-speed signal processing system adopts an integrated system design. The hardware part introduces the design method of signal integrity analysis to design high-speed digital...[Details]
0 Introduction
Due to the large number and variety of electronic equipment in special vehicles, the limited management capabilities of traditional semi-automatic power distribution methods...[Details]
1 Introduction
With the increasing electrification and automation of automotive parts and the high requirements for noise, electromagnetic compatibility and efficiency of automotiv...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
