EEWORLDEEWORLDEEWORLD

Part Number

Search

2200JG1F508F3EB

Description
Strain Guage Sensor, Gage, -15Psi Min, 0Psi Max, 0.15%, 0.50-5.50V, Cylindrical
CategoryThe sensor    Sensor/transducer   
File Size507KB,4 Pages
ManufacturerGems Sensors & Controls
Download Datasheet Parametric View All

2200JG1F508F3EB Overview

Strain Guage Sensor, Gage, -15Psi Min, 0Psi Max, 0.15%, 0.50-5.50V, Cylindrical

2200JG1F508F3EB Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
MakerGems Sensors & Controls
Reach Compliance Codeunknown
Maximum accuracy(%)0.15%
shellSTAINLESS STEEL
Nominal offset0.50V
Maximum operating temperature50 °C
Minimum operating temperature-20 °C
Output range0.50-5.50V
Output typeANALOG VOLTAGE
Package Shape/FormCYLINDRICAL
port type1/8 NPT
Maximum pressure range
Minimum pressure range-15 Psi
Pressure sensing modeGAGE
Sensor/Transducer TypePRESSURE SENSOR,STRAIN GUAGE
Maximum supply voltage35 V
Minimum supply voltage1.5 V
Termination typeMETAL CABLE GLAND
Base Number Matches1
After a large-scale ransomware outbreak, a British cybersecurity staff member worked all night to analyze and accidentally discovered a message left by the virus author...
Here’s an interesting story: [color=#333333][font=Helvetica, STHeiti] After a large-scale virus outbreak yesterday, a British network security personnel worked all night to analyze and accidentally di...
王达业 Talking
"Embedded Hardware Design"--A good book for hardware engineers
Learning with peers...
a510729059 PCB Design
V2cpld_spi
[i=s]This post was last edited by paulhyde on 2014-9-15 09:14[/i] V2cpld_spi...
wangwei20060608 Electronics Design Contest
LIS3DH chip problem consultation
[table=98%] [tr][td][color=#444444]Hello everyone, I found a problem when I was doing LIS3DH motion detection. [/color][color=#444444]After configuring the registers of LIS3DH (configuring the motion ...
lskam stm32/stm8
The MCU cannot run in DC-DC mode of BLUENRG-1
In the DC-DC mode of BLUENRG, the voltage output is only about 0.5V, and the output of LDO is also only about 0.5V. The MCU cannot operate normally, and the SWD interface cannot be detected using J-li...
suwithin ST - Low Power RF
My emergency light is fully completed. See the picture.
All the components I used are from MAXIM. Although the workmanship is not very particular, you can take a look at them for reference. The pictures were supposed to be uploaded tomorrow, but because my...
ddllxxrr DIY/Open Source Hardware

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 40  2086  2180  743  20  1  43  44  15  46 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号