MBM29LV002BC-12 datasheet, PDF

Datasheet> All Categories > MBM29LV002BC-12

Preview

MBM29LV002BC-12: Description2M (256K x 8) BIT; File Size278KB，52 Pages; ManufacturerFUJITSU; Websitehttp://edevice.fujitsu.com/fmd/en/index.html

Download Datasheet View All

MBM29LV002BC-12 Overview

2M (256K x 8) BIT

Preview

Download Datasheet

View All

FUJITSU SEMICONDUCTOR

DATA SHEET

DS05-20863-3E

FLASH MEMORY

CMOS

2M (256K

8) BIT

MBM29LV002TC

70/-90/-12

/MBM29LV002BC

-70/-90/-12

FEATURES

• Single 3.0 V read, program, and erase

Minimizes system level power requirements

• Compatible with JEDEC-standard commands

Uses same software commands as E

PROMs

• Compatible with JEDEC-standard world-wide pinouts

40-pin TSOP(I) (Package suffix: PTN – Normal Bend Type, PTR – Reversed Bend Type)

40-pin SON (Package suffix: PNS)

• Minimum 100,000 program/erase cycles

• High performance

70 ns maximum access time

• Sector erase architecture

One 16K byte, two 8K bytes, one 32K byte, and three 64K bytes

Any combination of sectors can be concurrently erased. Also supports full chip erase

• Boot Code Sector Architecture

T = Top sector

B = Bottom sector

• Embedded Erase

Algorithms

Automatically pre-programs and erases the chip or any sector

• Embedded Program

Algorithms

Automatically writes and verifies data at specified address

• Data Polling and Toggle Bit feature for detection of program or erase cycle completion

• Ready/Busy output (RY/BY)

Hardware method for detection of program or erase cycle completion

• Automatic sleep mode

When addresses remain stable, automatically switch themselves to low power mode

• Low V

write inhibit

≤

2.5 V

• Erase Suspend/Resume

Suspends the erase operation to allow a read data in another sector within the same device

• Sector protection

Hardware method disables any combination of sectors from program or erase operations

• Sector Protection Set function by Extended sector protection command

• Temporary sector unprotection

Temporary sector unprotection via the RESET pin

Embedded Erase

and Embedded Program

are trademarks of Advanced Micro Devices, Inc.

MBM29LV002TC

-70/-90/-12

/MBM29LV002BC

-70/-90/-12

GENERAL DESCRIPTION

The MBM29LV002TC/BC are a 2M-bit, 3.0 V-only Flash memory organized as 256K bytes of 8 bits each. The

MBM29LV002TC/BC are offered in a 40-pin TSOP(I) and 40-pin SON packages. These devices are designed

to be programmed in-system with the standard system 3.0 V V

supply. 12.0 V V

and 5.0 V V

are not required

for write or erase operations. The devices can also be reprogrammed in standard EPROM programmers.

The standard MBM29LV002TC/BC offer access times 70 ns and 120 ns, allowing operation of high-speed

microprocessors without wait states. To eliminate bus contention the devices have separate chip enable (CE),

write enable (WE), and output enable (OE) controls.

The MBM29LV002TC/BC are pin and command set compatible with JEDEC standard E

PROMs. Commands

are written to the command register using standard microprocessor write timings. Register contents serve as

input to an internal state-machine which controls the erase and programming circuitry. Write cycles also internally

latch addresses and data needed for the programming and erase operations. Reading data out of the devices

is similar to reading from 5.0 V and 12.0 V Flash or EPROM devices.

The MBM29LV002TC/BC are programmed by executing the program command sequence. This will invoke the

Embedded Program Algorithm which is an internal algorithm that automatically times the program pulse widths

and verifies proper cell margin. Typically, each sector can be programmed and verified in about 0.5 seconds.

Erase is accomplished by executing the erase command sequence. This will invoke the Embedded Erase

Algorithm which is an internal algorithm that automatically preprograms the array if it is not already programmed

before executing the erase operation. During erase, the devices automatically time the erase pulse widths and

verify proper cell margin.

Any individual sector is typically erased and verified in 1.0 second. (If already completely preprogrammed.)

The devices also feature a sector erase architecture. The sector mode allows each sector to be erased and

reprogrammed without affecting other sectors. The MBM29LV002TC/BC are erased when shipped from the

factory.

The devices feature single 3.0 V power supply operation for both read and write functions. Internally generated

and regulated voltages are provided for the program and erase operations. A low V

detector automatically

inhibits write operations on the loss of power. The end of program or erase is detected by Data Polling of DQ

by the Toggle Bit feature on DQ

, or the RY/BY output pin. Once the end of a program or erase cycle has been

completed, the devices internally reset to the read mode.

Fujitsu’s Flash technology combines years of EPROM and E

PROM experience to produce the highest levels

of quality, reliability, and cost effectiveness. The MBM29LV002TC/BC memories electrically erase the entire chip

or all bits within a sector simultaneously via Fowler-Nordhiem tunneling. The bytes are programmed one byte

at a time using the EPROM programming mechanism of hot electron injection.

Recommended Resources

Low-frequency signal decomposition circuit using AD7520

Little Swan CXW-180-99A two-wheel type range hood circuit diagram

OM391 type circuit

Double T-shaped RC oscillator circuit diagram

Standard image generator with frequency synthesizer

Simple single-chip karaoke circuit

2021 Python Developer Survey Results: This is the fifth official annual Python Developer Survey, conducted in partnership between the Python Software Foundation and JetBrains. In the fall of 2021, more than 23,000 Python developers and en...; dcexpert MicroPython Open Source section

The dish is useless: Reactive power only includes reactive current and reactive power, but not reactive voltage. Reactive power is dependent on the power supply. Offline current (for example, the permanent current of a su...; hk6108 Integrated technical exchanges

WINCE writes garbled characters in the registry: [code] int MAX_SIZE = 256; HKEY hKey1; wchar_t *key1Value = L"abc";//The result is the same if written in Chinese char *key1buf = new char[MAX_SIZE]; memset(key1buf,0,MAX_SIZE); int size = 0;//The num...; ghmgs Embedded System

About Ultra-Wideband UWB Wireless Transceiver Module: Hello, have you ever worked on an ultra-wideband project? I would like to ask about the products of ultra-wideband wireless transceiver modules. Which ones can be obtained in China now? Thank you!...; cocoshine Embedded System

Can someone please give me some clear direction?: I really want to learn embedded knowledge, but I really don’t know where to start. I’ve been confused for many days. Please give me some direction!...; sypanyue Embedded System

【ESP8266】Install esptool.py: When using the ESP8266 module, some flashing software is usually used. The official provides download tools such as nodemcu_flasher, ESPFlashDownloadTool, and ESP8266Flasher, but lacks lower-level too...; dcexpert MicroPython Open Source section

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components