ESD Diodes
MAZW000H Series
Silicon planar type
Unit: mm
For surge absorption circuit
■
Features
•
Two elements anode-common type
•
SSS-Mini type 3-pin package
0.33
+0.05
–0.02
3
0.10
+0.05
–0.02
(0.40) (0.40)
0.80
±0.05
1.20
±0.05
5˚
0.15 min.
0.23
+0.05
–0.02
1
2
■
Absolute Maximum Ratings
T
a
=
25°C
Parameter
Total power dissipation
*
Junction temperature
Storage temperature
Symbol
P
tot
T
j
T
stg
Rating
150
150
−55
to
+150
Unit
mW
°C
°C
0 to 0.01
0.52
±0.03
5˚
Note) *: P
tot
= 150 mW achieved with a printed circuit board.
1: Cathode 1
2: Cathode 2
3: Anode 1, 2
SSSMini3-F1 Package
Internally connected circuit
3
1
2
■
Common Electrical Characteristics
T
a
= 25°C
±
3°C
Parameter
Zener voltage
*
Zener rise operating resistance
Zener operating resistance
Reverse current
Symbol
V
Z
R
ZK
R
Z
I
R
I
Z
I
Z
I
Z
V
R
Conditions
Specified value
Specified value
Specified value
Specified value
Refer to the list of the
electrical characteristics
within part numbers
Min
Typ
Max
Unit
V
Ω
Ω
µA
Note) 1. Measuring methods are based JAPANESE INDUSTRIAL STANDARD JIS C 7031 measuring methods for diodes.
2. Electrostatic breakdown voltage is
±10
kV
Test method: IEC1000-4-2 (C
=
150 pF, R
=
330
Ω,
Contact discharge: 10 times)
3. *: The temperature must be controlled 25°C for V
Z
mesurement.
V
Z
value measured at other temperature must be adjusted to V
Z
(25°C)
V
Z
guaranted 20 ms after current flow.
0.15 max.
0.15 min.
0.80
±0.05
1.20
±0.05
Publication date: 30 June, 2003
SKE00019AED
1
Request for your special attention and precautions in using the technical information
and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Government
if any of the products or technologies described in this material and controlled under the "Foreign
Exchange and Foreign Trade Law" is to be exported or taken out of Japan.
(2) The technical information described in this material is limited to showing representative characteris-
tics and applied circuits examples of the products. It neither warrants non-infringement of intellec-
tual property right or any other rights owned by our company or a third party, nor grants any license.
(3) We are not liable for the infringement of rights owned by a third party arising out of the use of the
product or technologies as described in this material.
(4) The products described in this material are intended to be used for standard applications or general
electronic equipment (such as office equipment, communications equipment, measuring instru-
ments and household appliances).
Consult our sales staff in advance for information on the following applications:
•
Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment,
combustion equipment, life support systems and safety devices) in which exceptional quality and
reliability are required, or if the failure or malfunction of the products may directly jeopardize life or
harm the human body.
•
Any applications other than the standard applications intended.
(5) The products and product specifications described in this material are subject to change without
notice for modification and/or improvement. At the final stage of your design, purchasing, or use of
the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that
the latest specifications satisfy your requirements.
(6) When designing your equipment, comply with the guaranteed values, in particular those of maxi-
mum rating, the range of operating power supply voltage, and heat radiation characteristics. Other-
wise, we will not be liable for any defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of
incidence of break down and failure mode, possible to occur to semiconductor products. Measures
on the systems such as redundant design, arresting the spread of fire or preventing glitch are
recommended in order to prevent physical injury, fire, social damages, for example, by using the
products.
(7) When using products for which damp-proof packing is required, observe the conditions (including
shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets
are individually exchanged.
(8) This material may be not reprinted or reproduced whether wholly or partially, without the prior written
permission of Matsushita Electric Industrial Co., Ltd.
2002 JUL
京公网安备 11010802033920号
EEWORLD
