Operating Temperature Range .........................-55°C to +135°C
Storage Temperature Range .............................-65°C to +165°C
Lead Temperature (soldering, 10s) .................................+300°C
Soldering Temperature (reflow) .......................................+260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
CC
= +2.7V to +5.5V, R
PULLUP
= 100kΩ (MAX6501/MAX6503 only), T
A
= T
MIN
to T
MAX
, unless otherwise noted. Typical values are
at T
A
= +25°C.) (Note 1)
PARAMETER
Supply Voltage Range
Supply Current
Temperature Threshold
Accuracy (Note 2)
SYMBOL
V
CC
I
CC
-45°C to -25°C
ΔT
TH
-15°C to +15°C
+35°C to +65°C
+75°C to +125°C
Temperature Threshold
Hysteresis
HYST Input Threshold
(Note 3)
T
HYST
V
IH
V
IL
I
SOURCE
= 500µA, V
CC
> 2.7V
(MAX6502/MAX6504 only)
I
SOURCE
= 800µA, V
CC
> 4.5V
(MAX6502/MAX6504 only)
I
SINK
= 1.2mA, V
CC
> 2.7V
I
SINK
= 3.2mA, V
CC
> 4.5V
V
CC
= 2.7V, V
TUNDER
= 5.5V (MAX6503),
V
TOVER
= 5.5V (MAX6501)
10
0.8 x V
CC
V
V
CC
- 1.5
0.3
0.4
V
nA
HYST = GND
HYST = V
CC
0.8 x V
CC
0.2 x V
CC
-6
-4
-4
-6
CONDITIONS
MIN
2.7
30
±0.5
±0.5
±0.5
±0.5
2
10
TYP
MAX
5.5
85
+6
+4
+4
+6
°C
V
°C
UNITS
V
µA
Output Voltage High
V
OH
Output Voltage Low
Open-Drain Output Leakage
Current
V
OL
Note 1:
100% production tested at T
A
= +25°C. Specifications over temperature limits are guaranteed by design.
Note 2:
The MAX6501–MAX6504 are available with internal, factory-programmed temperature trip thresholds from -45°C to +125°C
[postbg]bg7.png[/postbg][font=楷体, 楷体_GB2312][size=4] Last time, I chose a single-chip microcomputer from Renesas as the main control chip of the SI4432 wireless transceiver module. In the subsequent d...
Some pins in the DSP have internal pull-ups. What is the purpose of this pull-up? What does its pull-up current of 100uA mean? Is Vcc already connected to the pull-up resistor, or does it need to be c...
How to get the information of SD card in Windows? How to get the information of several important registers of SD card? For example, register OCR, CSD, etc. Which API function can be used to get it? O...
WinCE4.2 system made with 2440... I have 2 SD cards and 2 TF cards. As a result, one of the SD cards was inserted into the device, and the debugging information was output: charlie::Prescale for Real ...
1. Introduction to the onboard serial port of the GD32L233C-START evaluation boardThe specific chip model used in the GD32L233C-START evaluation board is GD32L233CCT6, which supports 2-way UART, full-...
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
The Portable Digital Data Acquisition System (PDDAS) uses LabVIEW Real-Time and PXI to control the wind tunnel test and record air pressure data from 128 different channels.
"The LabVIEW Real-...[Details]
1. Introduction
With the gradual automation and modernization of industrial control systems, fieldbus control systems have received more and more attention and application. CAN bus is currentl...[Details]
We know that microcontroller development tools generally include real-time online emulators and programmers. Among them, online emulators are very good tools, but they are also more expensive...[Details]
5. Identifiers and keywords of C language
A complete PIC microcontroller C language program usually consists of six parts: include files (i.e. header files 1, variable definitions, variable de...[Details]
Vertical cavity surface emitting lasers (VCSELs) are gradually replacing traditional edge emitting lasers, especially in low bandwidth and short-distance communication systems where cost factors ar...[Details]
1. System Structure
This system is a simulation system of indoor air-conditioning temperature/humidity control system. The data acquisition and control center collects temperature/humidity...[Details]
1 Introduction
The Third Steel Plant of Jigang Group is a key investment project of Jigang Group during the "15th Five-Year Plan". It has introduced first-class domestic and foreign advanced eq...[Details]
The concept of state machine
State machine is an important concept in software programming. More important than this concept is its flexible application. In a clear and efficient program, ther...[Details]
Capacitors
are basic components in various electronic devices and are widely used for bypassing, coupling,
filtering
, tuning, etc. in electronic circuits. However, to use capacitors,...[Details]
With concerns about the growing energy crisis, motor efficiency has become an important and timely topic. This is because motors use 63% to 70% of the electricity produced in the United States and ...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
