EEWORLDEEWORLDEEWORLD

Part Number

Search

935296524125

Description
Interface Circuit
CategoryAnalog mixed-signal IC    Drivers and interfaces   
File Size450KB,35 Pages
ManufacturerNXP
Websitehttps://www.nxp.com
Download Datasheet Parametric Compare View All

935296524125 Overview

Interface Circuit

935296524125 Parametric

Parameter NameAttribute value
MakerNXP
Reach Compliance Codeunknown
Interface integrated circuit typeINTERFACE CIRCUIT
Base Number Matches1
PCA9306
Dual bidirectional I
2
C-bus and SMBus voltage-level translator
Rev. 8 — 22 January 2014
Product data sheet
1. General description
The PCA9306 is a dual bidirectional I
2
C-bus and SMBus voltage-level translator with an
enable (EN) input, and is operational from 1.0 V to 3.6 V (V
ref(1)
) and 1.8 V to 5.5 V
(V
bias(ref)(2)
).
The PCA9306 allows bidirectional voltage translations between 1.0 V and 5 V without the
use of a direction pin. The low ON-state resistance (R
on
) of the switch allows connections
to be made with minimal propagation delay. When EN is HIGH, the translator switch is on,
and the SCL1 and SDA1 I/O are connected to the SCL2 and SDA2 I/O, respectively,
allowing bidirectional data flow between ports. When EN is LOW, the translator switch is
off, and a high-impedance state exists between ports.
The PCA9306 is not a bus buffer like the PCA9509 or PCA9517A that provide both level
translation and physically isolates the capacitance to either side of the bus when both
sides are connected. The PCA9306 only isolates both sides when the device is disabled
and provides voltage level translation when active.
The PCA9306 can also be used to run two buses, one at 400 kHz operating frequency
and the other at 100 kHz operating frequency. If the two buses are operating at different
frequencies, the 100 kHz bus must be isolated when the 400 kHz operation of the other
bus is required. If the master is running at 400 kHz, the maximum system operating
frequency may be less than 400 kHz because of the delays added by the translator.
As with the standard I
2
C-bus system, pull-up resistors are required to provide the logic
HIGH levels on the translator’s bus. The PCA9306 has a standard open-collector
configuration of the I
2
C-bus. The size of these pull-up resistors depends on the system,
but each side of the translator must have a pull-up resistor. The device is designed to work
with Standard-mode, Fast-mode and Fast-mode Plus I
2
C-bus devices in addition to
SMBus devices. The maximum frequency is dependent on the RC time constant, but
generally supports > 2 MHz.
When the SDA1 or SDA2 port is LOW, the clamp is in the ON-state and a low resistance
connection exists between the SDA1 and SDA2 ports. Assuming the higher voltage is on
the SDA2 port when the SDA2 port is HIGH, the voltage on the SDA1 port is limited to the
voltage set by VREF1. When the SDA1 port is HIGH, the SDA2 port is pulled to the drain
pull-up supply voltage (V
pu(D)
) by the pull-up resistors. This functionality allows a
seamless translation between higher and lower voltages selected by the user without the
need for directional control. The SCL1/SCL2 channel also functions as the SDA1/SDA2
channel.

935296524125 Related Products

935296524125 935283119118 935290855125 PCA9306GD1,125 PCA9306DC1 PCA9306DC,125 935283118118 935283122125 935283123125 935283124125
Description Interface Circuit Interface Circuit Interface Circuit IC TRNSLTR BIDIRECTIONAL 8XSON Level converter Interface Circuit Interface Circuit Interface Circuit Interface Circuit
Reach Compliance Code unknown unknown unknown compliant compliant compliant unknown unknown unknown unknown
Interface integrated circuit type INTERFACE CIRCUIT INTERFACE CIRCUIT INTERFACE CIRCUIT INTERFACE CIRCUIT INTERFACE CIRCUIT INTERFACE CIRCUIT INTERFACE CIRCUIT INTERFACE CIRCUIT INTERFACE CIRCUIT INTERFACE CIRCUIT
Maker NXP NXP NXP NXP NXP NXP NXP - - -
Renesas CubeSuite+ development environment installation
Yesterday, the day before the high temperature holiday, I received the board and emulator, which looked very mini. Today, I started working after lunch. I downloaded CubeSuite, installed it, and then ...
Laspide Renesas Electronics MCUs
GPRS, RFID application solutions based on EM-STM3210E development board
[font=宋体][color=#000000]Solution Introduction: This module integrates three functional modules: GPRS/CDMA and RFID. It can be used together with the MCU board EM-STM3210E to realize wireless POS syste...
ye0217 stm32/stm8
Which types of LEDs are susceptible to electrostatic damage and failure?
Static electricity is actually composed of accumulated charges. In daily life, especially in dry weather, people feel "electric shock" when they touch doors and windows with their hands. This is the "...
qwqwqw2088 LED Zone
Title: What happens if the ground wire and the change are connected in reverse?
Content: As the title says, please help me...
zf_zxsk Analog electronics
Renesas Technology Questions
Where can I open the project explorer in e2 studio?...
1225791222 Electronics Design Contest
How to calculate impedance (Part 2)
Last time, we talked about the "art of trade-offs" between impedance calculation and process technology. This is mainly to achieve our impedance control goals while ensuring the convenience of process...
edadoc PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2414  1335  633  1359  2191  49  27  13  28  45 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号