EEWORLDEEWORLDEEWORLD

Part Number

Search

3-5499206-3

Description
44 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER
CategoryThe connector    The connector   
File Size644KB,5 Pages
ManufacturerTE Connectivity
Websitehttp://www.te.com
Environmental Compliance  
Download Datasheet Parametric View All

3-5499206-3 Online Shopping

Suppliers Part Number Price MOQ In stock  
3-5499206-3 - - View Buy Now

3-5499206-3 Overview

44 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER

3-5499206-3 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Objectid2108681477
Reach Compliance Codeunknown
ECCN codeEAR99
Other featuresAMP-LATCH, POLARIZED
Connector typeBOARD CONNECTOR
Contact to complete cooperationNOT SPECIFIED
Contact point genderMALE
Contact materialNOT SPECIFIED
DIN complianceNO
Filter functionNO
IEC complianceNO
MIL complianceNO
Mixed contactsNO
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
Number of rows loaded2
OptionsGENERAL PURPOSE
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts44
UL Flammability Code94V-0
Product
Specification
108-40018
11Mar11 Rev F
AMP-LATCH* and IDC Header Connectors, .100 X .100 Inch Grid
1.
1.1.
SCOPE
Content
This specification covers perform ance, tests and quality requirem ents for AMP-LATCH* universal and
low profile, and IDC standard and low profile .100 X .100 inch grid headers, right angle and vertical
assem blies.
1.2.
Qualification
W hen tests are perform ed on subject product line, procedures specified in Figure 1 shall be used. All
inspections shall be perform ed using applicable inspection plan and product drawing.
1.3.
Successful qualification testing on the subject product line was com pleted on 03Nov95, additional
testing was com pleted on 23Feb10. The Qualification Test Report num ber for this testing is 501-325.
This docum entation is on file at and available from Engineering Practices and Standards (EPS).
APPLICABLE DOCUM ENTS
The following docum ents form a part of this specification to the extent specified herein. Unless
otherwise specified, the latest edition of the docum ent applies. In the event of conflict between the
requirem ents of this specification and the product drawing, the product drawing shall take precedence.
In the event of conflict between the requirem ents of this specification and referenced docum ents, this
specification shall take precedence.
2.1.
TE Connectivity (TE) Docum ents
!
!
!
2.2.
109-1: Test Specification (General Requirem ents for Test Specifications)
109 Series: Test Specifications as indicated in Figure 1
501-325: Qualification Test Report (Connector, AMPLATCH* Header, .100 X .100 Inch Grid)
2.
Industry Docum ent
EIA-364: Electrical Connector/Socket Test Procedures Including Environm ental Classifications
2.3.
Reference Docum ent
109-197: Test Specification (Tyco Electronics Test Specifications vs EIA and IEC Test Methods)
3.
3.1.
REQUIREM ENTS
Design and Construction
Product shall be of design, construction and physical dim ensions specified on applicable product
drawing.
3.2.
Materials
Materials used in the construction of this product shall be as specified on the applicable product
drawing.
©2011 Tyco Electronics Corporation, | Indicates change
a TE Connectivity Ltd. Company
*Trademark
All Rights Reserved
TE logo is a trademark.
For latest revision, visit our website at www.te.com/documents.
For Regional Customer Service, visit our website at www.te.com
Other products, logos, and company names might be trademarks of their respective owners.
1 of 5
LOC B
Has anyone used a Type-C female socket before? Can you help me check if the power pin position is correct?
The Type-C female socket I bought has not arrived yet, and I am in a hurry to make a board. Can you help me check if the 5V and ground pins are connected correctly?...
z45217 PCB Design
Ask a question about the make command
Hello everyone:When I install a software, I need to use the make command to compile the makefile in it before the installation is successful. However, I have installed the MinGW software and replaced ...
hellomankind Integrated technical exchanges
Please allow me to be a hand-giving party and ask for information on stm32
My internship company uses stm32, I have never learned it before, please provide some information, preferably from beginner to complex, thank you...
天天1 stm32/stm8
STM32F302R8 external/internal clock measurement application
[backcolor=rgb(239, 245, 249)]In the reference manual, there is a section on the RCC chapter, which says that the frequency of the external/internal clock can be measured through channel 1 of TIM16. [...
jplzl10000 stm32/stm8
msgQreceive returns error, what does it mean?
Does it mean that there is no data in the queue, or is there some other error? What usually causes this? Thanks a lot...
gtongy Embedded System
Principle and design of programmable voltage source system using FPGA2
In the program, duty is the parameter for controlling the duty cycle; count is the parameter for controlling the frequency division. By changing the two parameters of duty and count, a clock signal wi...
eeleader FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 531  2574  2876  781  2767  11  52  58  16  56 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号