EEWORLDEEWORLDEEWORLD

Part Number

Search

28P271-6

Description
RF BNC Connector, Male, Cable Mount, Crimp Terminal, Plug
CategoryThe connector    The connector   
File Size485KB,10 Pages
ManufacturerCarlisle Interconnect Components
Download Datasheet Parametric View All

28P271-6 Overview

RF BNC Connector, Male, Cable Mount, Crimp Terminal, Plug

28P271-6 Parametric

Parameter NameAttribute value
Reach Compliance Codeunknown
Other featuresINDUSTRY STANDARD:MIL-C-39012, CRIMP CAPTIVE CONTACT
Body/casing typePLUG
Characteristic impedance50 Ω
Connector typeRF BNC CONNECTOR
Contact point genderMALE
Coupling typeBAYONET
DIN complianceNO
Filter functionNO
IEC complianceNO
Insertion loss0.2 dB
insulator materialPTFE
MIL complianceYES
Manufacturer's serial numberBNC
Installation methodRIGHT ANGLE
Installation typeCABLE
Maximum operating frequency4 GHz
Panel mountingNO
Termination typeCRIMP
voltage standing wave ratio1.3
Base Number Matches1
Why do my emulator XRD-DSP510USB always have errors when emulating the target board?
When my emulator XRD-DSP510USB is simulating with the target board, an error message always appears: "however the partid register may not have been read properly due to the target statel. please reset...
redrosezlj DSP and ARM Processors
On-site photos of two 5.8G relay stations
Two pairs of 5.8G bridges, one pair for 30km, one pair for 8kmThe one above is for 30km, using 600mw TT58-600, with 29dBi dish antennaThe conical one is the 600mw TT58-600, you see the row of 5 red li...
clark RF/Wirelessly
Graduation project help! More details...
The minimum system performance requirement for DSP5509 is the lowest, and it is OK to run a minimum program. For details, please add Q: 76777689, label: 5509. There will be a generous reward! I forgot...
memory0425 DSP and ARM Processors
[Help] Voltage Mode Oscillation
[table][tr][td]It oscillates at about 50% duty, input 8V, output 4V; or input 15V, output 7.5V (rough estimate); there is no problem if the duty is lower or higher than this. Voltage mode, built-in ty...
tonytong Power technology
Please teach me how to use Wce Ui? ?
How do I use the UI I downloaded from http://www.wceui.cn/download.html?...
mjwqh Embedded System
Relay
Good blow, I'm a novice! I want to use a microcontroller to control the heat blocks and the like through relays. If I use a HK400F relay, can I directly connect it to 220V? How do I connect those term...
258121131 51mcu

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 794  256  893  1189  2764  16  6  18  24  56 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号