crystal oscillators in most electronic systems. The
ICS302 can accept a higher frequency clock input
to generate up to 200 MHz. The devices contain a
One Time Programmable (OTP) ROM which is
factory programmed with the PLL divider values
to output a broad range of frequencies, from 6 to
200 MHz, allowing customer requests for different
frequencies to be shipped in 1-3 days. Using
Phase-Locked-Loop (PLL) techniques, the devices
run from a standard fundamental mode,
inexpensive crystal, or clock. They are smaller and
less expensive than one oscillator.
Features
• Packaged as 8 pin SOIC
• Quick turn frequency programming allows
samples in one to three days
• Replaces nearly any crystal or oscillator
• ICS300 produces up to 100 MHz at 3.3V,
ICS301 produces up to 200 MHz at 3.3V
ICS302 accepts up to 125 MHz clock input
• Easy to cascade with ICS5xx series
• Input crystal frequency of 5 - 27 MHz
• Input clock frequency of 2 - 125 MHz
• Low jitter - 50 ps one sigma
• Compatible with all popular CPUs
• Duty cycle of 45/55
• Operating voltages of 3.0 to 5.5V
• Full CMOS level outputs with 25mA drive
capability at TTL levels
• Tri-state output + PLL power down pin
• Advanced, low power CMOS process
Block Diagram
VDD GND
Crystal
or clock
input
OTP
ROM
with PLL
Divider
Values
X1/ICLK
PLL
Clock
Synthesis
and Control
Circuitry
Output
Buffer
CLK
Crystal
Oscillator
X2
Divide
Logic and
Output
Buffer
REF
PDTS (both outputs and PLL)
MDS 300QT E
1
Revision 111000
Integrated Circuit Systems, Inc. • 525 Race Street • San Jose •CA•95126•(408) 295-9800tel• www.icst.com
ICS300/ICS301/ICS302
QTClock™ Quick Turn Clock Synthesizer
Pin Assignments
X1/ICLK
VDD
GND
REF
GND
VDD
GND
REF
8
1
2 ICS300 7
3 ICS301 6
4
5
1
2 ICS302
3
4
8
7
6
5
X2
PDTS
DC
CLK
ICLK
PDTS
DC
CLK
REF Clock Options
REF
Reference
Reference/2
CLK/2
Off
Comments
Buffered oscillator output
Oscillator frequency divided by two
CLK frequency divided by two
Output stopped low. Lowest jitter
Pin Descriptions
Number Number Name
Type Description
300/1
302
1
8
X1/ICLK
I
Crystal connection or clock input. Clock only on ICS302.
2
2
VDD
P Connect to +3.3V or +5V.
3
1, 3
GND
P Connect to ground.
4
4
REF
O Buffered crystal oscillator output clock, or variation per REF clock options table above.
5
5
CLK
O Clock output. Fixed frequency between 6 and 200 MHz programmed at factory.
6
6
DC
-
Don't Connect anything to this pin.
7
7
PDTS
I
Powers down PLL, and puts both outputs into high impedance state, when low.
8
-
X2
O Crystal connection. Leave unconnected for clock input.
Key: I = Input, O = output, P = power supply connection
Device Configuration
The specification is complete when the ICS300/301/302 QTClock Order Form accompanies this data
sheet. The order form lists the input, REF, and CLK actual frequencies, as well as any other available
options. This unique configuration is given a two character alphanumeric programming code, which must
be specified when referring to samples.
External Components / Crystal Selection
The ICS300/301/302 requires a 0.01µF decoupling capacitor to be connected between VDD and GND.
It must be connected close to the ICS300/301/302 to minimize lead inductance. No external power
supply filtering is required for this device. A 33Ω terminating resistor can be used next to the CLK and
REF pins. The total on-chip capacitance is approximately 16 pF, so a parallel resonant, fundamental mode
crystal should be used. For crystals with a specified load capacitance greater than 16 pF, crystal capacitors
can be connected from each of the pins X1 and X2 to Ground. The value (in pF) of these crystal caps
should be = (CL -16)*2, where CL is the crystal load capacitance in pF. These external capacitors are only
required for applications where the exact frequency is critical. For a clock input, connect to X1/ICLK and
leave X2 unconnected (no capacitors on either).
MDS 300QT E
2
Revision 111000
Integrated Circuit Systems, Inc. • 525 Race Street • San Jose •CA•95126•(408) 295-9800tel• www.icst.com
ICS300/ICS301/ICS302
QTClock™ Quick Turn Clock Synthesizer
Electrical Specifications
Parameter
Conditions
Minimum
Typical
ABSOLUTE MAXIMUM RATINGS (stresses beyond these can permanently damage the device)
Supply Voltage, VDD
Referenced to GND
Inputs
Referenced to GND
-0.5
Clock Output
Referenced to GND
-0.5
Ambient Operating Temperature
0
Soldering Temperature
Max of 10 seconds
Storage temperature
-65
DC CHARACTERISTICS (VDD = 5.0V unless otherwise noted)
Operating Voltage, VDD
3
Input High Voltage, VIH, ICLK only
ICLK (Pin 1)
(VDD/2)+1
VDD/2
Input Low Voltage, VIL, ICLK only
ICLK (Pin 1)
VDD/2
Input High Voltage, VIH
PDTS
2
Input Low Voltage, VIL
PDTS
Output High Voltage, VOH
IOH=-4mA
VDD-0.4
Output High Voltage, VOH
IOH=-25mA
2.4
Output Low Voltage, VOL
IOL=25mA
IDD Operating Supply Current, 20 MHz crystal No Load, 100MHz
20
Short Circuit Current
CLK output
±70
On-Chip Pull-up Resistor, PDTS
Pin 7
270
Input Capacitance, PDTS
Pin 7
4
AC CHARACTERISTICS (VDD = 5.0V unless otherwise noted)
Input Frequency, crystal input, ICS300 and 301
5
Input Frequency, clock input, ICS300 and 301
2
Input Frequency, clock input, ICS302
50
Output Frequency, ICS300
VDD = 4.5 to 5.5V
6
Output Frequency, ICS300
VDD = 3.0 to 3.6V
6
Output Frequency, ICS301 and ICS302
VDD = 4.5 to 5.5V
6
Output Frequency, ICS301 and ICS302
VDD = 3.0 to 3.6V
6
Output Clock Rise Time
0.8 to 2.0V
1
Output Clock Fall Time
2.0 to 0.8V
1
Output Clock Duty Cycle (Note 1)
at programmed level
45
49 to 51
Absolute Clock Period Jitter
Deviation from mean
±120
One Sigma Clock Period Jitter
50
Power-up time, PDTS goes high until Refer. out Reference on REF clk
3
Power-up time, PDTS goes high until CLK out
8
Maximum
7
VDD+0.5
VDD+0.5
70
260
150
5.5
(VDD/2)-1
0.4
Units
V
V
V
°C
°C
°C
V
V
V
V
V
V
V
V
mA
mA
kΩ
pF
MHz
MHz
MHz
MHz
MHz
MHz
MHz
ns
ns
%
ps
ps
ms
ms
0.4
27
50
125
160
100
200
200
55
10
20
Note 1: These are typical values. The actual minimum and maximum duty cycle limits are shown on the
ICS300/301/302 QTClock Order Form for each programmed version.
MDS 300QT E
3
Revision 111000
Integrated Circuit Systems, Inc. • 525 Race Street • San Jose •CA•95126•(408) 295-9800tel• www.icst.com
ICS300/ICS301/ICS302
QTClock™ Quick Turn Clock Synthesizer
Package Outline and Package Dimensions
(
For current dimensional specifications, see JEDEC Publication No. 95.)
8 pin SOIC
E
Pin 1
H
Symbol
A
A1
B
C
D
A1
e
B
C
h x 45°
A
L
D
E
e
H
h
L
Inches
Min
Max
0.0532 0.0688
0.0040 0.0098
0.0130 0.0200
0.075
0.098
0.1890 0.1968
0.1497 0.1574
.050 BSC
0.2284 0.2440
0.0099 0.0195
0.0160 0.0500
Millimeters
Min
Max
1.35
1.75
0.10
0.24
0.33
0.51
1.91
2.40
4.80
5.00
3.80
4.00
1.27 BSC
5.80
6.20
0.25
0.50
0.41
1.27
Ordering Information
Part/Order Number
ICS300M-xx
ICS300MT-xx
ICS301M-xx
ICS301MT-xx
ICS302M-xx
ICS302MT-xx
Marking
ICS300M
ICS300M
ICS301M
ICS301M
ICS302M
ICS302M
Package
8 pin SOIC
8 pin SOIC on tape and reel
8 pin SOIC
8 pin SOIC on tape and reel
8 pin SOIC
8 pin SOIC on tape and reel
Temperature
0 to 70 °C
0 to 70 °C
0 to 70 °C
0 to 70 °C
0 to 70 °C
0 to 70 °C
xx represents a 2 character alphanumeric programming code assigned by the factory, which indicates the
output frequencies on CLK and REF. All samples are shipped with an ICS300/301/302 order form
describing the characteristics of the device.
While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems, Inc. (ICS) assumes no responsibility for either its use or for
the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use
in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements
are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any
ICS product for use in life support devices or critical medical instruments.
QTClock is a trademark of ICS
MDS 300QT E
4
Revision 111000
Integrated Circuit Systems, Inc. • 525 Race Street • San Jose •CA•95126•(408) 295-9800tel• www.icst.com
[i=s]This post was last edited by Digital Leaf on 2021-6-17 22:00[/i]I was going to write SPI_FLASH read and write operations, but I found that I had to write QSPI_FLASH first, because after using RT-...
[size=2] The 256/512Byte SRAM integrated in the MCU of SC91F722/721/733/832/831 etc. has the function of saving RAM data when power is off: that is, within a certain range that cannot meet the normal ...
I am preparing to participate in the "TI" electronic design competition recently, and I have been cramming knowledge about launch pads. Through learning from videos and other materials, I found that I...
As an engineer, I often come into contact with debugging M core MCU, so we need to debug the emulator. Usually everyone buys the emulator. Although I have many emulators, I prefer to research and make...
Here is an active antenna, which can be used as an antenna for medium wave, FM and short wave. In the short wave band, the receiving performance of this active antenna is equivalent to that of a 20-30...
Abstract: In order to generate a stable excitation signal, the design of a digital frequency synthesizer is implemented on FPGA using Verilog hardware language. The design includes accumulator, wav...[Details]
Vertical cavity surface emitting lasers (VCSELs) are gradually replacing traditional edge emitting lasers, especially in low bandwidth and short-distance communication systems where cost factors ar...[Details]
A standard cell
is an electrochemical
cell
used as a voltage reference standard in many electrical standards laboratories
. If properly maintained, standard cells are very stable. The ...[Details]
This controller uses PIC16C54 single-chip microcomputer as the controller, and it is very easy to use: just connect a telephone line to the loudspeaker through the controller, and you can rem...[Details]
In industry, voltage 0…5 (10) V or current 0 (4)…20 mA is usually used as a method for analog signal transmission, which is also a method often used by programmable controllers. So what are the dif...[Details]
0 Introduction
With the rapid development of modern power electronics technology, various power electronic devices have been widely used in various fields such as power systems, industry, an...[Details]
Designing low power circuits while achieving acceptable performance is a difficult task. Doing so in
the RF
bands increases the challenge dramatically. Today, nearly everything has wireless...[Details]
introduction
Sudan's Muglad Oilfield is a large oilfield jointly invested, developed and constructed by a four-party consortium of China, Malaysia, Canada and Sudan. It consists of 8 satellite...[Details]
Globally, the market for airbags and other restraint systems consists of different geographical regions, each with its own characteristics and needs. North America first introduced airbags in mass-...[Details]
The rotor of the brushless DC motor used in electric bicycles is composed of 30 to 40 pieces of NdFeB magnets. Since the surface magnetic field strength of NdFeB magnets exceeds 500mT, the position se...[Details]
As a type of iron battery, lithium iron phosphate battery (hereinafter referred to as lithium iron battery) has always been widely concerned by industry friends (some people say that lithium iron b...[Details]
1. Electromagnetic compatibility design
Electromagnetic compatibility refers to the ability of electronic equipment to work in a coordinated and effective manner in various electromagnetic env...[Details]
Modern communication equipment, portable electronic products, laptops, electric vehicles, small satellites, etc. generally use batteries as power sources and are widely used. However, the batteries...[Details]
illustrate]
This method has
the characteristics of small
ROM
occupation
and fast operation speed, with a range of
2000
ßà
2099
,
a total of
...[Details]
Thyristor is the abbreviation of thyristor, commonly known as silicon controlled rectifier. It is a high-power switching semiconductor device, represented by the letter symbols "V" or "VT" in the c...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
