crystal oscillators in most electronic systems. The
ICS302 can accept a higher frequency clock input
to generate up to 200 MHz. The devices contain a
One Time Programmable (OTP) ROM which is
factory programmed with the PLL divider values
to output a broad range of frequencies, from 6 to
200 MHz, allowing customer requests for different
frequencies to be shipped in 1-3 days. Using
Phase-Locked-Loop (PLL) techniques, the devices
run from a standard fundamental mode,
inexpensive crystal, or clock. They are smaller and
less expensive than one oscillator.
Features
• Packaged as 8 pin SOIC
• Quick turn frequency programming allows
samples in one to three days
• Replaces nearly any crystal or oscillator
• ICS300 produces up to 100 MHz at 3.3V,
ICS301 produces up to 200 MHz at 3.3V
ICS302 accepts up to 125 MHz clock input
• Easy to cascade with ICS5xx series
• Input crystal frequency of 5 - 27 MHz
• Input clock frequency of 2 - 125 MHz
• Low jitter - 50 ps one sigma
• Compatible with all popular CPUs
• Duty cycle of 45/55
• Operating voltages of 3.0 to 5.5V
• Full CMOS level outputs with 25mA drive
capability at TTL levels
• Tri-state output + PLL power down pin
• Advanced, low power CMOS process
Block Diagram
VDD GND
Crystal
or clock
input
OTP
ROM
with PLL
Divider
Values
X1/ICLK
PLL
Clock
Synthesis
and Control
Circuitry
Output
Buffer
CLK
Crystal
Oscillator
X2
Divide
Logic and
Output
Buffer
REF
PDTS (both outputs and PLL)
MDS 300QT E
1
Revision 111000
Integrated Circuit Systems, Inc. • 525 Race Street • San Jose •CA•95126•(408) 295-9800tel• www.icst.com
ICS300/ICS301/ICS302
QTClock™ Quick Turn Clock Synthesizer
Pin Assignments
X1/ICLK
VDD
GND
REF
GND
VDD
GND
REF
8
1
2 ICS300 7
3 ICS301 6
4
5
1
2 ICS302
3
4
8
7
6
5
X2
PDTS
DC
CLK
ICLK
PDTS
DC
CLK
REF Clock Options
REF
Reference
Reference/2
CLK/2
Off
Comments
Buffered oscillator output
Oscillator frequency divided by two
CLK frequency divided by two
Output stopped low. Lowest jitter
Pin Descriptions
Number Number Name
Type Description
300/1
302
1
8
X1/ICLK
I
Crystal connection or clock input. Clock only on ICS302.
2
2
VDD
P Connect to +3.3V or +5V.
3
1, 3
GND
P Connect to ground.
4
4
REF
O Buffered crystal oscillator output clock, or variation per REF clock options table above.
5
5
CLK
O Clock output. Fixed frequency between 6 and 200 MHz programmed at factory.
6
6
DC
-
Don't Connect anything to this pin.
7
7
PDTS
I
Powers down PLL, and puts both outputs into high impedance state, when low.
8
-
X2
O Crystal connection. Leave unconnected for clock input.
Key: I = Input, O = output, P = power supply connection
Device Configuration
The specification is complete when the ICS300/301/302 QTClock Order Form accompanies this data
sheet. The order form lists the input, REF, and CLK actual frequencies, as well as any other available
options. This unique configuration is given a two character alphanumeric programming code, which must
be specified when referring to samples.
External Components / Crystal Selection
The ICS300/301/302 requires a 0.01µF decoupling capacitor to be connected between VDD and GND.
It must be connected close to the ICS300/301/302 to minimize lead inductance. No external power
supply filtering is required for this device. A 33Ω terminating resistor can be used next to the CLK and
REF pins. The total on-chip capacitance is approximately 16 pF, so a parallel resonant, fundamental mode
crystal should be used. For crystals with a specified load capacitance greater than 16 pF, crystal capacitors
can be connected from each of the pins X1 and X2 to Ground. The value (in pF) of these crystal caps
should be = (CL -16)*2, where CL is the crystal load capacitance in pF. These external capacitors are only
required for applications where the exact frequency is critical. For a clock input, connect to X1/ICLK and
leave X2 unconnected (no capacitors on either).
MDS 300QT E
2
Revision 111000
Integrated Circuit Systems, Inc. • 525 Race Street • San Jose •CA•95126•(408) 295-9800tel• www.icst.com
ICS300/ICS301/ICS302
QTClock™ Quick Turn Clock Synthesizer
Electrical Specifications
Parameter
Conditions
Minimum
Typical
ABSOLUTE MAXIMUM RATINGS (stresses beyond these can permanently damage the device)
Supply Voltage, VDD
Referenced to GND
Inputs
Referenced to GND
-0.5
Clock Output
Referenced to GND
-0.5
Ambient Operating Temperature
0
Soldering Temperature
Max of 10 seconds
Storage temperature
-65
DC CHARACTERISTICS (VDD = 5.0V unless otherwise noted)
Operating Voltage, VDD
3
Input High Voltage, VIH, ICLK only
ICLK (Pin 1)
(VDD/2)+1
VDD/2
Input Low Voltage, VIL, ICLK only
ICLK (Pin 1)
VDD/2
Input High Voltage, VIH
PDTS
2
Input Low Voltage, VIL
PDTS
Output High Voltage, VOH
IOH=-4mA
VDD-0.4
Output High Voltage, VOH
IOH=-25mA
2.4
Output Low Voltage, VOL
IOL=25mA
IDD Operating Supply Current, 20 MHz crystal No Load, 100MHz
20
Short Circuit Current
CLK output
±70
On-Chip Pull-up Resistor, PDTS
Pin 7
270
Input Capacitance, PDTS
Pin 7
4
AC CHARACTERISTICS (VDD = 5.0V unless otherwise noted)
Input Frequency, crystal input, ICS300 and 301
5
Input Frequency, clock input, ICS300 and 301
2
Input Frequency, clock input, ICS302
50
Output Frequency, ICS300
VDD = 4.5 to 5.5V
6
Output Frequency, ICS300
VDD = 3.0 to 3.6V
6
Output Frequency, ICS301 and ICS302
VDD = 4.5 to 5.5V
6
Output Frequency, ICS301 and ICS302
VDD = 3.0 to 3.6V
6
Output Clock Rise Time
0.8 to 2.0V
1
Output Clock Fall Time
2.0 to 0.8V
1
Output Clock Duty Cycle (Note 1)
at programmed level
45
49 to 51
Absolute Clock Period Jitter
Deviation from mean
±120
One Sigma Clock Period Jitter
50
Power-up time, PDTS goes high until Refer. out Reference on REF clk
3
Power-up time, PDTS goes high until CLK out
8
Maximum
7
VDD+0.5
VDD+0.5
70
260
150
5.5
(VDD/2)-1
0.4
Units
V
V
V
°C
°C
°C
V
V
V
V
V
V
V
V
mA
mA
kΩ
pF
MHz
MHz
MHz
MHz
MHz
MHz
MHz
ns
ns
%
ps
ps
ms
ms
0.4
27
50
125
160
100
200
200
55
10
20
Note 1: These are typical values. The actual minimum and maximum duty cycle limits are shown on the
ICS300/301/302 QTClock Order Form for each programmed version.
MDS 300QT E
3
Revision 111000
Integrated Circuit Systems, Inc. • 525 Race Street • San Jose •CA•95126•(408) 295-9800tel• www.icst.com
ICS300/ICS301/ICS302
QTClock™ Quick Turn Clock Synthesizer
Package Outline and Package Dimensions
(
For current dimensional specifications, see JEDEC Publication No. 95.)
8 pin SOIC
E
Pin 1
H
Symbol
A
A1
B
C
D
A1
e
B
C
h x 45°
A
L
D
E
e
H
h
L
Inches
Min
Max
0.0532 0.0688
0.0040 0.0098
0.0130 0.0200
0.075
0.098
0.1890 0.1968
0.1497 0.1574
.050 BSC
0.2284 0.2440
0.0099 0.0195
0.0160 0.0500
Millimeters
Min
Max
1.35
1.75
0.10
0.24
0.33
0.51
1.91
2.40
4.80
5.00
3.80
4.00
1.27 BSC
5.80
6.20
0.25
0.50
0.41
1.27
Ordering Information
Part/Order Number
ICS300M-xx
ICS300MT-xx
ICS301M-xx
ICS301MT-xx
ICS302M-xx
ICS302MT-xx
Marking
ICS300M
ICS300M
ICS301M
ICS301M
ICS302M
ICS302M
Package
8 pin SOIC
8 pin SOIC on tape and reel
8 pin SOIC
8 pin SOIC on tape and reel
8 pin SOIC
8 pin SOIC on tape and reel
Temperature
0 to 70 °C
0 to 70 °C
0 to 70 °C
0 to 70 °C
0 to 70 °C
0 to 70 °C
xx represents a 2 character alphanumeric programming code assigned by the factory, which indicates the
output frequencies on CLK and REF. All samples are shipped with an ICS300/301/302 order form
describing the characteristics of the device.
While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems, Inc. (ICS) assumes no responsibility for either its use or for
the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use
in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements
are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any
ICS product for use in life support devices or critical medical instruments.
QTClock is a trademark of ICS
MDS 300QT E
4
Revision 111000
Integrated Circuit Systems, Inc. • 525 Race Street • San Jose •CA•95126•(408) 295-9800tel• www.icst.com
Suppose there is such a human-machine interface board... responsible for password entry, a large number of numerical settings, (3 levels +) menu display, and such a control board, responsible for the ...
Download source package:
https://www.embedthis.com/esp/download.html
The version I downloaded is : esp-8.0.3-src.tgz
Unzip:
$ cd
$ tar xf esp-8.0.3-src.tgz
$ cd esp-8.0.3/Source cross-compilation tool...
If I work in embedded systems, what are the advantages and disadvantages? (I mean, my undergraduate major is electrical engineering and automation, what knowledge should I focus on self-study?) Also, ...
I bought a cheap knockoff TWS headset a few months ago and have been planning to take it apart. A few days ago, I finally found an opportunity to take apart the charging box and share it with you.Earp...
①Why should we learn and use oscilloscopes?②Introduction to oscilloscope probes, measurement and compensation calibration③Vertical system of new oscilloscopes④Horizontal system of new oscilloscopes⑤Cu...
As the title says; do I need to connect a serial port to USB (such as PL2303)? I heard that this board is very powerful and can be directly connected to the USB cable, but there is no port (COM port)....
A single-chip microcomputer is also called a single-chip microcontroller. It is not a chip that completes a certain logical function, but a computer system integrated into one chip. In general, a c...[Details]
In
circuit design,
current
measurement
is widely used, and the main fields are divided into three categories: in measurement,
the electric meter
is used to measure the curre...[Details]
0 Introduction
With the development of my country's economy, the number of motor vehicles continues to increase. The growth of existing roads and other hardware facilities can no longer meet t...[Details]
China's new energy vehicles are in a transition period from research and development to real industrial development. In 2012, with the intensive launch of new energy vehicle policy planning, the de...[Details]
introduction
For the voltage regulator modules (VRMs) that power the latest computer central processing units (CPUs), power supply designers have historically used multiphase interleaved b...[Details]
In the previous series, we have listed some basic knowledge of C language in Tables 1 to 3. We hope that beginners can strengthen their memory of the above tables and gradually learn to use them wh...[Details]
Among the many members of the single-chip microcomputer family, the MCS-51 series of single-chip microcomputers has occupied the main market of industrial measurement and control and automation eng...[Details]
From the previous section, we have learned that the timer/counter in the microcontroller can have multiple uses, so how can I make them work for the purpose I need? This requires setting the timer/...[Details]
Printed circuit boards ( PCBs
)
are used in most electrical products
. If a PCB has low
insulation resistance
(IR), the performance of the circuits on the PCB will be greatly reduced...[Details]
LED lighting: Basic circuit design can be completed in as little as one day
Semiconductor manufacturers are also getting involved in the LED lighting business. The power circuit of LED req...[Details]
This article will introduce a design method for a distributed control system used in a tracking car, which can perform distributed control of motor modules, sensor modules, and lighting control mod...[Details]
With the rapid development of cities and the improvement of citizens' living standards, the number of various vehicles in cities is growing, and the demand for parking spaces in major commercial an...[Details]
Key Points
1. Now, in addition to high-end smartphones and tablets, users also expect to use touch screens in other applications, and they are gradually appearing in cars and instruments.
...[Details]
The ARINC429 bus is one of the most commonly used communication buses between various subsystems of avionics. As the "skeleton" of modern avionics systems, once the bus system or the attached airbo...[Details]
Introduction
Today, as IC (integrated circuit) has developed to a super-large scale, IC design based on IP (Intellectual Property) cores and their reuse are important means to ensure the ef...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
