EEWORLDEEWORLDEEWORLD

Part Number

Search

3GDW14G-E-30N-0.750

Description
LVDS Output Clock Oscillator, 0.75MHz Nom, ROHS COMPLIANT, DIP-14/4
CategoryPassive components    oscillator   
File Size114KB,1 Pages
ManufacturerEuroquartz
Websitehttp://www.euroquartz.co.uk/
Environmental Compliance
Download Datasheet Parametric View All

3GDW14G-E-30N-0.750 Overview

LVDS Output Clock Oscillator, 0.75MHz Nom, ROHS COMPLIANT, DIP-14/4

3GDW14G-E-30N-0.750 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Reach Compliance Codecompliant
Maximum control voltage3 V
Minimum control voltage0.3 V
maximum descent time0.7 ns
Frequency Adjustment - MechanicalNO
Frequency offset/pull rate30 ppm
frequency stability50%
Installation featuresTHROUGH HOLE MOUNT
Nominal operating frequency0.75 MHz
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Oscillator typeLVDS
Output load50 OHM
physical size20.2mm x 12.8mm x 5.08mm
longest rise time0.7 ns
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
Nominal supply voltage3.3 V
surface mountNO
maximum symmetry55/45 %
Base Number Matches1
EURO
QUARTZ
14 pin Dual-in-Line
Frequency range 38MHz to 640MHz
LVDS Output
Supply Voltage 3.3 VDC
Phase jitter 0.4ps typical
Pull range from ±30ppm to ±150ppm
GDW14 LVDS VCXO
750.0kHz to 800.0MHz
DESCRIPTION
GDW14 VCXOs are packaged in an industry-standard, 14 pin dual-
in-line package. Typical phase jitter for GDW series VCXOs is 2.35ps.
Output is LVDS. Applications include phase lock loop, SONET/ATM,
set-top boxes, MPEG , audio/video modulation, video game consoles
and HDTV.
SPECIFICATION
Frequency Range:
Supply Voltage:
Output Logic:
RMS Period Jitter:
Peak to Peak Jitter:
Phase Jitter:
Initial Frequency Accuracy:
Output Voltage HIGH (1):
Output Voltage LOW (0):
Pulling Range:
Control Voltage Range:
Temperature Stability:
Output Load:
Rise/Fall Times:
Duty Cycle:
Start-up Time:
Current Consumption:
Static Discharge Protection:
Storage Temperature:
Ageing:
Enable/Disable:
RoHS Status:
OUTLINE & DIMENSIONS
750kHz to 800.0MHz
3.3 VDC ±5%
LVDS
4.3ps typical
27.0ps typical
2.35ps typical
Tune to the nominal frequency
with Vc= 1.65 ±0.2VDC
1.4 Volts typical
1.1 Volts typical
From ±30ppm to ±150ppm
1.65 ±1.35 Volts
See table
50W into Vdd or Thevenin equiv.
0.5ns typ., 0.7ns max.
20% Vdd to 80% Vdd
50% ±5%
(Measured at Vdd-1.3V)
10ms maximum, 5ms typical
55mA typical, 60mA maximum
(At 202.50MHz)
2kV maximum
-55° to +150°C
±2ppm per year maximum
Not implemented - 4 pin package
Fully compliant or non compliant
PART NUMBERING
Example:
3GDW14G-B-80N-60.000
FREQUENCY STABILITY
Stability Code Stability ±ppm Temp. Range
A
25
0°~+70°C
B
50
0°~+70°C
C
100
0°~+70°C
D
25
-40°~+85°C
E
50
-40°~+85°C
F
100
-40°~+85°C
If non-standard frequency stability is required
Use ‘I’ followed by stability, i.e. I20 for ±20ppm
Supply Voltage
3 = +3.3V
Series Designator
GDW14
RoHS Status
G = RoHs compliant
Blank = RoHS non-compliant
Stability over temperature range
(See table)
Pullability in ±ppm
Pullability determinator
N = minimum
M = maximum
T = Typical
Frequency in MHz
EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE
Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 info@euroquartz.co.uk www.euroquartz.co.uk
Help with C language microcontroller program (very simple question)
I'm begging for a very simple delay program, but when I actually simulate or run it, the program always jumps inexplicably. The picture is as follows. The gray part is where it actually runs. I don't ...
henry9374 MCU
About LVPECL Signaling
I use max9372 to convert a TTL signal into LVPECL signal. Why can't I test this LVPECL signal with an oscilloscope in the circuit? There is only a DC bias voltage, and the chip is fine, because if the...
feitian9215 Embedded System
What is the maximum serial port rate supported by STM32F405 or MicroPython? Is 921600 supported?
[i=s] This post was last edited by shenshen927 on 2017-8-26 14:13 [/i] I have the following questions: 1. What is the highest serial port rate that STM32F405 or MicroPython can support? Does it suppor...
shenshen927 MicroPython Open Source section
Q&A: SI4463 PCB design guidance
After adding the words "You ask me, I answer", the question will be taken care of. I just hope to solve the problem. ^ _ ^ I just finished drawing a PCB. Of course, my skills are still far behind thos...
lonerzf PCB Design
Where should a novice start learning embedded systems?
I am a fresh graduate majoring in electrical automation, and I really want to develop in the field of embedded systems. However, I have only learned 80c51 microcontrollers and C language, and now I do...
zhangliang13032 Embedded System
Clock sampling system minimizes jitter
Reprinted from: deyisupport [font=normal 宋体, Arial, Helvetica, sans-serif][color=#000000][size=12px]Author: Richard Zarr[/size][/color][/font] [align=left][color=#000]It is well known that jitter (whi...
maylove Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2315  2670  575  42  2006  47  54  12  1  41 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号