EEWORLDEEWORLDEEWORLD

Part Number

Search

5223033-4

Description
CONNECTOR, 540 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, PRESS FIT, ROHS COMPLIANT
CategoryThe connector    The connector   
File Size401KB,8 Pages
ManufacturerTE Connectivity
Websitehttp://www.te.com
Environmental Compliance
Download Datasheet Parametric View All

5223033-4 Overview

CONNECTOR, 540 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, PRESS FIT, ROHS COMPLIANT

5223033-4 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
package instructionROHS COMPLIANT
Reach Compliance Codeunknown
Other featuresZ-PACK
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (30)
Contact completed and terminatedTIN
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
DIN complianceNO
Filter functionNO
IEC complianceNO
JESD-609 codee3
MIL complianceNO
Manufacturer's serial number5223033
Mixed contactsNO
Installation methodSTRAIGHT
Installation typeBOARD
Number of rows loaded5
OptionsGENERAL PURPOSE
Terminal pitch2 mm
Termination typePRESS FIT
Total number of contacts540
Base Number Matches1
Product
Specification
Connector, Z-PACK*, 2 mm FB, Signal and Power
1.
1.1.
SCOPE
Content
108-1441
11Mar11 Rev C
This specification covers performance, tests and quality requirements for the Z-PACK* 2mm FB
connector system. This connector system is a backplane bus system which interconnects printed circuit
boards using pin and receptacle connectors. Connectors employ a four row 2mm centerline
configuration. Being through hole devices, pin and receptacle contacts have either solder or press fit
leads.
1.2.
Qualification
When tests are performed on the subject product line, procedures specified in 109 Series Test
Specifications shall be used. All inspections shall be performed using the applicable inspection plan and
product drawing.
2.
APPLICABLE DOCUMENTS
The following documents form a part of this specification to the extent specified herein. Unless
otherwise specified, the latest edition of the document applies. In the event of conflict between
requirements of this specification and the product drawing, the product drawing shall take precedence.
In the event of conflict between requirements of this specification and referenced documents, this
specification shall take precedence.
2.1.
TE Connectivity (TE) Documents
!
!
!
3.
3.1.
109-1: General Requirements for Test Specifications
109 Series: Test Specifications as indicated in Figure 1
501-334: Qualification Test Report
REQUIREMENTS
Design and Construction
Product shall be of design, construction and physical dimensions specified on the applicable product
drawing.
3.2.
Materials
!
Contact:
Signal/power pin: Phosphor bronze, gold over palladium nickel over nickel plating
Signal receptacle: Copper nickel zinc, gold over palladium nickel over nickel plating
Power receptacle: Beryllium copper, gold over palladium nickel over nickel plating
Housing: High temperature thermoplastic, liquid crystal polymer
!
©2011 Tyco Electronics Corporation, | Indicates change
a TE Connectivity Ltd. Company
*Trademark
All Rights Reserved
TE logo is a trademark.
For latest revision, visit our website at www.te.com/documents.
For Regional Customer Service, visit our website at www.te.com
Other products, logos, and company names might be trademarks of their respective owners.
1 of 8
LOC B
PHILIPS single chip 16-32 bit LPC2292-2294
PHILIPS single chip 16-32 bit LPC2292-2294 mainly introduces the LP C2292--2994 series of single chip microcomputers...
rain Test/Measurement
Mini motorcycle lock anti-theft alarm
1. Overview: There are many types of anti-theft alarms. We are now introducing a mini motorcycle lock anti-theft alarm. This alarm is installed in the motorcycle lock. As long as the lock is opened fo...
rain MCU
About Flash memory sectors, blocks, and pages
Take W25Q128 as an example:128Mbit capacity.256 bytes per page, a total of 65536 bytes, a total of 65536*256*8=134,217,728bit, equal to 134,217,728/1024/1024=128Mbit. Each programming data is 256 byte...
Jacktang DSP and ARM Processors
STM32 running error
I wrote a uart program, using STM32F103RB .\Obj\STM32_FD_USART1.axf: Error: L6218E: Undefined symbol RxBuffer1 (referred from stm32f10x_it.o). Why is this? Thank you....
3008202060 stm32/stm8
SD card for STM323
The SD card initialization of STM323 is always unsuccessful, and the CMD1 response is incorrect. Does anyone know? Please give me some advice...
qiuzhi339 stm32/stm8
Are you interested in woodworking? Are you interested in this DIY wooden bed?
[color=#000]想给家里的小朋友买张木床,合适的都需要订做,最快一个月,是从其他城市做好运过来的。。。。在网上看了台湾网友的DIY自己手也有些痒痒,转过来给大家看下,顺便问问有没有喜欢做木工的 ----------------------------------分割线------------------------------------------ 時間退回到 今年過年 [/color]...
赵玉田 DIY/Open Source Hardware

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 629  692  769  1544  2700  13  14  16  32  55 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号