• Optimized for clock distribution in DDR (Double Data Rate)
SDRAM applications
• Operating frequency: 60MHz to 200MHz
• Standard speed: PC1600 (DDR200), PC2100 (DDR266)
• A speed: PC1600 (DDR200), PC2100 (DDR266), PC2700 (DDR333)
• 1 to 10 differential clock distribution
• Very low skew (<100ps)
• Very low jitter (<75ps)
• 2.5V AV
DD
and 2.5V V
DDQ
• CMOS control signal input
• Test mode enables buffers while disabling PLL
• Low current power-down mode
• Tolerant of Spread Spectrum input clock
• Available in 48-pin TSSOP and 56-pin VFBGA packages
The CSPT857 is a PLL based clock driver that acts as a zero delay buffer
to distribute one differential clock input pair(CLK,
CLK
) to 10 differential output
pairs (Y
[0:9]
, Y
[0:9]
) and one differential pair of feedback clock output (FBOUT,
FBOUT).
External feedback pins (FBIN,
FBIN)
for synchronization of the
outputs to the input reference is provided. A CMOS Enable/Disable pin is
available for low power disable. When the output frequency falls below
approximately 20MHz, the device will enter power down mode. In this mode,
the receivers are disabled, the PLL is turned off, and the output clock drivers
are tristated, resulting in a current consumption device of less than 200µA.
The CSPT857 requires no external components and has been optimised
for very low I/O phase error, skew, and jitter, while maintaining frequency and
duty cycle over the operating voltage and temperature range. The CSPT857,
designed for use in both module assemblies and system motherboard based
solutions, provides an optimum high-performance clock source.
The CSPT857 is only available in Industrial Temperature Range (-40°C to
+85°C), and CSPT857A is only available in Commercial Temperature Range
(0°C to +70°C). See Ordering Information for details.
FUNCTIONAL BLOCK DIAGRAM
PWRDWN
37/E6
AV
DD
16/G2
TEST
MODE
LOGIC
3/A1
Y0
2/A2
Y0
5/B2
6/B1
10/D1
9/D2
Y1
Y1
Y2
Y2
20/J2
Y3
19/J1
22/K1
Y3
Y4
23/K2
Y4
Y5
CLK
CLK
FBIN
FBIN
13/F1
14/F2
46/A6
47/A5
44/B5
43/B6
39/D6
40/D5
29/J5
30/J6
PLL
36/F6
35/F5
Y5
Y6
Y6
Y7
Y7
Y8
Y8
Y9
Y9
FBOUT
FBOUT
27/K6
26/K5
32/H6
33/H5
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
1
c
2002
Integrated Device Technology, Inc.
OCTOBER 2002
DSC-5172/8
IDTCSPT857/A
2.5V PLL DIFFERENTIAL 1:10 SDRAM CLOCK DRIVER
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
PIN CONFIGURATIONS
PWR
DWN
6
Y
5
Y
5
Y
6
Y
6
GND
GND
NC
NC
GND
GND
C
Y
7
Y
7
NC
NC
Y
2
Y
2
D
FBIN
V
DDQ
FBOUT
Y
8
Y
8
Y
9
Y
9
5
V
DDQ
FBIN FBOUT GND
NC
NC
V
DDQ
V
DDQ
E
4
GND V
DDQ
GND V
DDQ
Y
0
Y
0
A
NC
NC
V
DDQ
GND
V
DDQ
GND
Y
3
Y
3
J
3
2
Y
1
Y
1
B
CLK
CLK
F
AV
DD
GND
V
DDQ
AGND
G
H
Y
4
Y
4
K
1
VFBGA
TOP VIEW
56 BALL VFBGA PACKAGE LAYOUT
0.65mm
6
5
4
3
2
1
A
B
C
D
E
F
G
H
J
K
TOP VIEW
A
1
2
3
4
5
6
B
C
D
E
F
G
H
J
K
2
IDTCSPT857/A
2.5V PLL DIFFERENTIAL 1:10 SDRAM CLOCK DRIVER
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
PIN CONFIGURATION
GND
Y
0
Y
0
V
DDQ
Y
1
Y
1
GND
GND
Y
2
Y
2
V
DDQ
V
DDQ
CLK
CLK
V
DDQ
AV
DD
AGND
GND
Y
3
Y
3
V
DDQ
Y
4
Y
4
GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
GND
Y
5
Y
5
V
DDQ
Y
6
Y
6
GND
GND
Y
7
Y
7
V
DDQ
PWRDWN
FBIN
FBIN
V
DDQ
FBOUT
FBOUT
GND
Y
8
Y
8
V
DDQ
Y
9
Y
9
GND
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
V
DDQ
, AV
DD
Rating
Supply Voltage Range
Input Voltage Range
Voltage range applied to any
output in the high or low state
Input Clamp Current
Output Clamp Current
Max
–0.5 to +3.6
–0.5 to V
DDQ
+ 0.5
–0.5 to V
DDQ
+ 0.5
–50
±50
Unit
V
V
V
mA
mA
V
I(2)
V
O(2)
I
IK
(V
I
<0)
I
OK
(V
O
<0 or
V
O
> V
DDQ
)
Continuous Output Current
I
O
(V
O
=0 to V
DDQ
)
V
DDQ
or GND
TSTG
Continuous Current
Storage Temperature Range
±50
±100
– 65 to +150
mA
mA
°C
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
2. The input and output negative-voltage ratings may be exceeded if the input and output
clamp-current ratings are observed.
3. The maximum package power dissipation is calculated using a junction temperature
of 150
°
C and a board trace length of 750 mils.
CAPACITANCE
(1)
Parameter
C
IN
C
I(∆)
C
L
Description
Input Capacitance
V
I
= V
DDQ
or GND
Delta Input Capacitance
V
I
= V
DDQ
or GND
Load Capacitance
—
14
—
pF
NOTE:
1. Unused inputs must be held high or low to prevent them from floating.
Min.
2.5
-0.25
Typ.
—
—
Max.
3.5
0.25
Unit
pF
pF
TSSOP
TOP VIEW
RECOMMENDED OPERATING CONDITIONS
CSPT857
Symbol
AV
DD
V
DDQ
T
A
Supply Voltage
I/O Supply Voltage
Operating Free-Air Temperature
Parameter
Min.
2.3
-40
Typ.
V
DDQ
2.5
Max.
2.7
+85
Min.
V
DDQ
– 0.12
2.3
0
CSPT857A
Typ.
V
DDQ
2.5
Max.
2.7
2.7
+70
Unit
V
V
°
C
3
IDTCSPT857/A
2.5V PLL DIFFERENTIAL 1:10 SDRAM CLOCK DRIVER
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
PIN DESCRIPTION (TSSOP)
Pin Name
AGND
AV
DD
CLK,
CLK
FBIN,
FBIN
FBOUT,
FBOUT
GND
PWRDWN
V
DDQ
Y
[0:9]
Y
[0:9]
Pin Number
17
16
13, 14
35, 36
32, 33
1, 7, 8, 18, 24, 25, 31, 41, 42, 48
37
4, 11, 12, 15, 21, 28, 34, 38, 45
3, 5, 10, 20, 22, 27, 29, 39, 44, 46
2, 6, 9, 19, 23, 26, 30, 40, 43, 47
2.5V analog supply
Differential clock input
Feedback differential clock input
Feedback differential clock output
Ground
Output enable for Y and
Y
2.5V supply
Buffered output of input clock, CLK
Buffered output of input clock,
CLK
Description
Ground for 2.5V analog supply
PIN DESCRIPTION (VFBGA)
Pin Name
AGND
AV
DD
CLK,
CLK
FBIN,
FBIN
FBOUT,
FBOUT
GND
PWRDWN
V
DDQ
Y
[0:9]
Y
[0:9]
Pin Number
H1
G2
F1, F2
F5, F6
H6, G5
A3, A4, C1, C2, C5, C6, H2, H5, K3, K4
E6
B3, B4, E1, E2, E5, G1, G6, J3, J4
A1, A6, B2, B5, D1, D6, J2, J5, K1, K6
A2, A5, B1, B6, D2, D5, J1, J6, K2, K5
2.5V analog supply
Differential clock input
Feedback differential clock input
Feedback differential clock output
Ground
Output enable for Y and
Y
2.5V supply
Buffered output of input clock, CLK
Buffered output of input clock,
CLK
Description
Ground for 2.5V analog supply
FUNCTION TABLE
(1)
INPUTS
AV
DD
GND
GND
X
X
2.5V (nom)
2.5V (nom)
2.5V (nom)
(2)
PWRDWN
H
H
L
L
H
H
X
CLK
L
H
L
H
L
H
<20MHz
CLK
H
L
H
L
H
L
<20MHz
Y
L
H
Z
Z
L
H
Z
Y
H
L
Z
Z
H
L
Z
OUTPUTS
FBOUT
L
H
Z
Z
L
H
Z
FBOUT
H
L
Z
Z
H
L
Z
PLL
Bypassed/OFF
Bypassed/OFF
OFF
OFF
ON
ON
OFF
NOTES:
1. H = HIGH Voltage Level
L = LOW Voltage Level
Z = High-Impedance OFF-State
X = Don't Care
2. Additional feature that senses when the clock input is less than approximately 20MHz and places the part in sleep mode. Reciever inputs and PLL are turned off and outputs
= tristate.
4
IDTCSPT857/A
2.5V PLL DIFFERENTIAL 1:10 SDRAM CLOCK DRIVER
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Commercial: T
A
= 0°C to +70°C; Industrial: T
A
= –40°C to +85°C
Symbol
V
IK
V
IL (dc)
V
IH (dc)
V
IL (ac)
V
IH (ac)
V
OL
V
OH
V
IX
V
ID(DC) (1)
V
ID(AC) (1)
I
IN
I
DDPD
I
DDQ
I
ADD
Parameter
Input Clamp Voltage (All Inputs)
Static Input LOW Voltage
Static Input HIGH Voltage
Dynamic Input LOW Voltage
Dynamic Input HIGH Voltage
Output LOW Voltage
Output HIGH Voltage
Input Differential Cross Voltage
DC Input Differential Voltage
AC Input Differential Voltage
Input Current
Power-Down Current on V
DDQ
and A
VDD
Dynamic Power Supply Current on V
DDQ
Dynamic Power Supply Current on A
VDD
V
DDQ
= 2.7V, V
I
= 0V to 2.7V
A
VDD
/V
DDQ
= Max., CLK = 0MHz or
PWRDWN
= L
A
VDD
/V
DDQ
= Max., CLK = 200MHz, 120Ω/14pF
A
VDD
/V
DDQ
= Max., CLK = 170MHz, 120Ω/14pF
A
VDD
/V
DDQ
= Max., CLK = 170MHz
NOTE:
1. V
ID
is the magnitude of the difference between the input level on CLK and the input level on
Fiber Optic Communication Systems
Fiber-Optic Communication Systems, 3rd Edition
[url=http://eu.wiley.com/WileyCDA/Section/id-302479.html?query=Govind+P.+Agrawal][color=#0000ff]Govind P. Agrawal[/colo...
I need to work on F4 chips recently, so I want to buy an F4 development board, preferably with E coins. :congratulate: If anyone has a board that is gathering dust, please sell it as soon as possible....
The STM32G474 integrates five independent 12 -bit ADCs with a sampling rate of 4Msps
Last time, I used STM32G474 to implement a sine signal generator
https://bbs.eeworld.com.cn/forum.php?mod=viewthrea...
[b]Impedance - a fundamental concept that underlies many industrial, instrumentation and automotive sensor applications[/b] [p=15, null, left][color=rgb(0, 0, 0)][font=Arial, Helvetica, sans-serif][si...
introduction
Since the beginning of the 21st century, the world of information has changed rapidly. Maybe a high-tech product will be released today and a better similar product will be releas...[Details]
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
1. Introduction
This design was made for participating in an electronic design competition. It effectively solved the problem of the operation and control of an electric car on a seesaw. The s...[Details]
With the advent of increasingly powerful processors, image sensors, memory, and other semiconductor devices, as well as the algorithms that enable them, computer vision can be implemented in a wide...[Details]
In recent years, the market for mobile/portable devices such as smartphones and laptops has continued to grow rapidly. While these products continue to integrate more new features to enhance the ...[Details]
1. Introduction
Light control circuit plays a vital role in urban street lamps or corridor lighting. With light control circuit, the lights can be automatically turned on and off according to ...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
On the afternoon of July 10, Beijing time, Taiwan's largest chip designer MediaTek expects its smartphone chip shipments to grow by double digits in the third quarter of this year, and the company is ...[Details]
Smart lighting control systems provide high controllability for various buildings and further enhance the level of green energy. They are the core products of energy conservation and digital techn...[Details]
With the continuous consumption of earth's energy and the scarcity of resources, the harm of greenhouse effect to human beings, and the serious pollution of the atmosphere to the earth, the intern...[Details]
The traditional display screen using 51 single-chip microcomputer to control LED dot matrix has relatively simple functions. If it is to achieve diversified functions, it often takes a lot of time ...[Details]
In recent years, with the rapid development of the information industry, dot matrix LED display screens have been widely used in various advertising and information display systems such as the fina...[Details]
FPGAs are used in 81% of electronic systems, including many commercial and defense products, and most FPGAs use BGA packaging. The BGA packaging is characterized by small solder balls and small sol...[Details]
As people's requirements for safety and comfort in the process of driving cars continue to increase, automotive radars are widely used in the car's adaptive cruise system, collision avoidance syste...[Details]
TI Technology Forum
京公网安备 11010802033920号
EEWORLD
