• N channel FET switches with no parasitic diode to V
CC
– Isolation under power-off conditions
– No DC path to V
CC
or GND
– 5V tolerant in OFF and ON state
• 5V tolerant I/Os
Ω
• Low R
ON
- 4Ω typical
• Flat R
ON
characteristics over operating range
• Rail-to-rail switching 0 - 5V
• Bidirectional dataflow with near-zero delay: no added ground
bounce
• Excellent R
ON
matching between channels
• V
CC
operation: 2.3V to 3.6V
• High bandwidth - up to 500MHz
• LVTTL-compatible control Inputs
• Undershoot Clamp Diodes on all switch and control Inputs
• Low I/O capacitance, 4pF typical
• Available in QSOP and TSSOP packages
DESCRIPTION:
The QS3VH384 HotSwitch is a high bandwidth, 10-bit bus switch. The
QS3VH384 has very low ON resistance, resulting in under 250ps propagation
delay through the switch. Two banks of five switches are controlled by
independent (xOE), LVTTL compatible signals for bidirectional data flow with
no added delay or ground bounce. In the ON state, the switch can pass signals
up to 5V. In the OFF state, the switches offer very high impedence at the
terminals.
The combination of near-zero propagation delay, high OFF impedance, and
over-voltage tolerance makes the QS3VH384 ideal for high performance
communications applications.
The QS3VH384 is characterized for operation from -40°C to +85°C.
APPLICATIONS:
•
•
•
•
•
Hot-swapping
10/100 Base-T, Ethernet LAN switch
Low distortion analog switch
Replaces mechanical relay
ATM 25/155 switching
FUNCTIONAL BLOCK DIAGRAM
A
0
B
0
A
4
B
4
A
5
B
5
A
9
B
9
1O E
2O E
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
INDUSTRIAL TEMPERATURE RANGE
1
c
2002 Integrated Device Technology, Inc.
AUGUST 2002
DSC-5895/9
IDTQS3VH384
2.5V / 3.3V 10-BIT HIGH BANDWIDTH BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
PIN CONFIGURATION
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
Description
Max
V
TERM
(2)
V
TERM
(3)
SupplyVoltage to Ground
DC Switch Voltage V
S
DC Input Voltage V
IN
AC Input Voltage (pulse width
≤20ns)
DC Output Current (max. sink current/pin)
Storage Temperature
–0.5 to +4.6
–0.5 to +5.5
–0.5 to +5.5
–3
120
–65 to +150
Unit
V
V
V
V
mA
°C
1OE
B
0
A
0
A
1
B
1
B
2
A
2
A
3
B
3
B
4
A
4
GND
1
2
3
4
5
6
7
8
9
1
0
1
1
1
2
2
4
2
3
2
2
2
1
2
0
1
9
1
8
1
7
1
6
1
5
1
4
1
3
V
CC
B
9
A
9
A
8
B
8
B
7
A
7
A
6
B
6
B
5
A
5
2OE
V
TERM
(3)
V
AC
I
OUT
T
STG
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
2. V
CC
terminals.
3. All terminals except V
CC
.
CAPACITANCE
(T
A
= +25°C, F = 1MHz, V
IN
= 0V, V
OUT
= 0V)
Symbol
C
IN
C
I/O
Parameter
(1)
Control Inputs
Quickswitch Channels (Switch OFF)
Quickswitch Channels (Switch ON)
Typ.
3
4
8
Max.
5
6
12
Unit
pF
pF
pF
QSOP/ TSSOP
TOP VIEW
C
I/O
NOTE:
1. This parameter is guaranteed but not production tested.
PIN DESCRIPTION
Pin Names
A
0
- A
9
B
0
- B
9
1OE, 2OE
I/O
I/O
I/O
I
Bus A
Bus B
Output Enable
Description
FUNCTION TABLE
(1)
1OE
H
L
H
L
2OE
H
H
L
L
B
0
- B
4
Z
A
0
- A
4
Z
A
0
- A
4
B
5
- B
9
Z
Z
A
5
- A
9
A
5
- A
9
Function
Disconnect
Connect
Connect
Connect
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
Z = High-Impedence
2
IDTQS3VH384
2.5V / 3.3V 10-BIT HIGH BANDWIDTH BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Industrial: T
A
= –40°C to +85°C, V
CC
= 3.3V ±0.3V
Symbol
V
IH
V
IL
I
IN
I
OZ
I
OFF
R
ON
Parameter
Input HIGH Voltage
Input LOW Voltage
Input Leakage Current (Control Inputs)
Off-State Current (Hi-Z)
Data Input/Output Power Off Leakage
Switch ON Resistance
for Control Inputs
Guaranteed Logic LOW
for Control Inputs
0V
≤
V
IN
≤
V
CC
0V
≤
V
OUT
≤
5V, Switches OFF
V
IN
or V
OUT
0V to 5V, V
CC
= 0V
V
CC
= 2.3V
Typical at V
CC
= 2.5V
V
CC
= 3V
NOTE:
1. Typical values are at V
CC
= 3.3V and T
A
= 25°C.
Test Conditions
Guaranteed Logic HIGH
V
CC
= 2.3V to 2.7V
V
CC
= 2.7V to 3.6V
V
CC
= 2.3V to 2.7V
V
CC
= 2.7V to 3.6V
Min.
1.7
2
—
—
—
—
—
Typ.
(1)
Max.
—
—
—
—
—
—
—
6
7
4
5
—
—
0.7
0.8
±1
±1
±1
8
9
6
8
Unit
V
V
µA
µA
µA
Ω
V
IN
= 0V
V
IN
= 1.7V
V
IN
= 0V
V
IN
= 2.4V
I
ON
= 30mA
I
ON
= 15mA
I
ON
= 30mA
I
ON
= 15mA
—
—
—
—
TYPICAL ON RESISTANCE vs V
IN
AT V
CC
= 3.3V
16
14
R
ON
(ohms)
12
10
8
6
4
2
0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
V
IN
(Volts)
3
IDTQS3VH384
2.5V / 3.3V 10-BIT HIGH BANDWIDTH BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
POWER SUPPLY CHARACTERISTICS
Symbol
I
CCQ
∆I
CC
I
CCD
Parameter
Quiescent Power Supply Current
Power Supply Current
(2,3)
per Input HIGH
Dynamic Power Supply Current
(4)
Test Conditions
(1)
V
CC
= Max., V
IN
= GND or V
CC
, f = 0
V
CC
= Max., V
IN
= 3V, f = 0 per Control Input
V
CC
= 3.3V, A and B Pins Open, Control Inputs
Toggling @ 50% Duty Cycle
NOTES:
1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics.
2. Per input driven at the specified level. A and B pins do not contribute to
∆Icc.
3. This parameter is guaranteed but not tested.
4. This parameter represents the current required to switch internal capacitance at the specified frequency. The A and B inputs do not contribute to the Dynamic Power Supply
Current. This parameter is guaranteed but not production tested.
Min.
—
—
Typ.
1
—
Max.
4
30
Unit
mA
µA
See Typical I
CCD
vs Enable Frequency graph below
TYPICAL I
CCD
vs ENABLE FREQUENCY CURVE AT V
CC
= 3.3V
12
10
8
I
CCD
(mA)
6
4
2
0
0
2
4
6
8
10
12
14
16
18
20
ENABLE FREQUENCY (MHz)
4
IDTQS3VH384
2.5V / 3.3V 10-BIT HIGH BANDWIDTH BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
T
A
= -40°C to +85°C
V
CC
= 2.5 ± 0.2V
(1)
Symbol
t
PLH
t
PHL
t
PZL
t
PZH
t
PLZ
t
PHZ
f
xOE
Parameter
Data Propagation Delay
(2,3)
Ax to/from Bx
Switch Turn-On Delay
xOE
to Ax/Bx
Switch Turn-Off Delay
xOE
to Ax/Bx
Operating Frequency -Enable
(2,5)
Min
.
(4)
V
CC
= 3.3 ± 0.3V
(1)
Min
.
(4)
1.5
1.5
Max.
0.2
7.5
7
20
Unit
ns
ns
ns
MHz
Max.
0.2
7.5
7
10
1.5
1.5
NOTES:
1. See Test Conditions under TEST CIRCUITS AND WAVEFORMS.
2. This parameter is guaranteed but not production tested.
3. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone
is of the order of 0.2ns at C
L
= 50pF. Since this time constant is much smaller than the rise and fall times of typical driving signals, it adds very little propagation delay to the
system. Propagation delay of the bus switch, when used in a system, is determined by the driving circuit on the driving side of the switch and its interaction with the load on
the driven side.
4. Minimums are guaranteed but not production tested.
:)[font=微软雅黑][size=4][color=#ff0000]First of all, I wish you all a happy Chinese New Year[/color][/size][/font]:)[font=微软雅黑][size=4] I recently recorded a DIY video of a wireless remote control handle...
SI engineer: "You may need to change all the routing for this part."I didn't expect to get this answer from the SI engineer: "No, I'm serious."A few short sentences can actually mean a lot. They not o...
In Vista, copy .inf to windows\inf and .sys to windows\system32\drivers. Insert the hardware, and it will prompt "New hardware found". Click "Automatic search and installation" (only this option, unli...
[i=s]This post was last edited by paulhyde on 2014-9-15 09:38[/i] With this program, you can automatically add comments to the assembly program without comments, so that novices can easily understand ...
1. Several nouns
ABI:
The specifications that an executable file must follow in order to run in a specific execution environment;
Separately generated relocatabl...[Details]
Whether it is an electric car or an ordinary fuel car, for the vast majority of car buyers, the final cost of use is what they care about most. For fuel cars, how to save fuel is what drivers care ...[Details]
Definition of interactive projection system:
Interactive projection systems, also known as multimedia interactive projection, are available in floor, wall, and tabletop interactive projection....[Details]
Recently, Joyson Electronics has made positive progress in the core technology research and development of the robot's "brain and brain" and key components, and launched the industry's first integr...[Details]
To improve the lateral active safety of intelligent connected vehicles, the identification and definition of unexpected functional safety scenarios for the EPS (Electronic Steering System) ...[Details]
Shenzhen Baowei Power Supply high frequency pure sine wave power, communication inverter power supply has two communication interfaces, RS232 and R485 interfaces, their functions and characteristic...[Details]
On August 21, it was reported that Intel's new generation of AI chip Jaguar Shores was recently exposed for the first time.
According to photos shared by Andreas Schilling, the Jaguar Shores t...[Details]
The Waveshare ESP32-P4-ETH is a compact ESP32-P4 development board with Ethernet and PoE support. It looks very similar to the Olimex ESP32-P4-DevKit, minus the pUEXT connector. However, we've also...[Details]
The power transmission system between a car's engine and drive wheels is called its drivetrain. It ensures the necessary traction and speed under various driving conditions, and coordinates these t...[Details]
Using an electronic load is like thinking of it as a resistor that dissipates the power supply's output. The most straightforward mode is the CR constant resistance mode. In this mode, by setting a...[Details]
Most electric vehicles currently lack a gearbox, only a single-speed reduction gearbox. This includes Teslas, but that doesn't mean electric vehicles don't need a gearbox. Thanks to the constant to...[Details]
On August 19th, Intel and Japan's SoftBank Group announced on Monday that SoftBank would invest $2 billion (approximately 14.376 billion RMB at the current exchange rate) in Intel. Under the agreem...[Details]
Which is brighter, the xenon lamp or the LED lamp?
Which is better, LED or xenon? Which is brighter? We asked experts about these questions. For those confused about this, let's take a look at...[Details]
Editor's Note: The development of the embodied/humanoid industry is currently gaining momentum. Application and technological breakthroughs in key components have become key requirements for the de...[Details]
The control of the frequency converter is nothing more than the basic logic of start, stop, forward, reverse, and speed regulation. These logics basically require the level state to be valid, rathe...[Details]
DIY/Open Source Hardware
京公网安备 11010802033920号
EEWORLD
