REVISIONS
LTR
A
B
DESCRIPTION
Changes in accordance with NOR 5962-R123-95.
Corrected figure 1 to move the side view of case outline X and Z to
the right side of the of the top view for the correct orientation. Figure
1; removed the min limit for the D dimension of 2.880 inches (73.15
mm) for the case outline Z. Redrew entire document. -sld
Add device type 02, class K, and radiation hardness assurance
(RHA) requirements for levels L and R.
DATE (YR-MO-DA)
95-05-02
98-07-22
APPROVED
K. A. Cottongim
K. A. Cottongim
C
00-04-26
Raymond Monnin
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
REV
SHEET
PREPARED BY
Steve L. Duncan
CHECKED BY
Michael C. Jones
C
1
C
2
C
3
C
4
C
5
C
6
C
7
C
8
C
9
C
10
C
11
C
12
STANDARD
MICROCIRCUIT
DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
POST OFFICE BOX 3990
COLUMBUS, OHIO 43216-5000
THIS DRAWING IS
AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
AMSC N/A
APPROVED BY
Kendall A. Cottongim
MICROCIRCUIT, HYBRID, LINEAR, 5-VOLT,
SINGLE CHANNEL, DC-DC CONVERTER
DRAWING APPROVAL DATE
94-05-13
REVISION LEVEL
C
SIZE
A
SHEET
CAGE CODE
67268
1 OF
12
5962-93068
DSCC FORM 2233
APR 97
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
5962-E226-00
1. SCOPE
1.1 Scope. This drawing documents five product assurance classes, class D (lowest reliability), class E, (exceptions), class
G (lowered high reliability), class H (high reliability), and class K, (highest reliability) and a choice of case outlines and lead
finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation
hardness assurance levels are reflected in the PIN.
1.2 PIN. The PIN shall be as shown in the following example:
5962
Federal
stock class
designator
\
~
~
~
RHA
designator
(see 1.2.1)
/
\/
Drawing number
~
~
~
-
93068
01
Device
type
(see 1.2.2)
~
~
~
H
Device
class
designator
(see 1.2.3)
~
~
~
Case
outline
(see 1.2.4)
~
~
~
X
Lead
finish
(see 1.2.5)
~
~
~
X
1.2.1 Radiation hardness assurance (RHA) designator. Device classes H and K RHA marked devices shall meet the
MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-
RHA device. Only the RHA levels specified herein are available. See 4.3.5.
1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01
02
Generic number
MTR2805S/883, MTR2805SF/883
SMTR2805S, SMTR2805SF
Circuit function
DC-DC converter, 25 W, 5 V output
DC-DC converter, 25 W, 5 V output
1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level as
follows:
Device class
D, E, G, H, or K
Device performance documentation
Certification and qualification to MIL-PRF-38534
1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
X
Z
Descriptive designator
See figure 1
See figure 1
Terminals
10
10
Package style
Dual-in-line
Flange mount
1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534.
1.3 Absolute maximum ratings. 1/
Input voltage range ....................................................................
Power dissipation (P
D
) ...............................................................
Output power .............................................................................
Lead soldering temperature (10 seconds) .................................
Storage temperature range........................................................
-0.5 V dc to +50 V dc
12 W
25.75 W
+300
q
C
-65
q
C to +150
q
C
1/
Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
SIZE
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
A
REVISION LEVEL
5962-93068
SHEET
C
2
DSCC FORM 2234
APR 97
1.4 Recommended operating conditions.
Input voltage range ....................................................................
Case operating temperature range (T
C
).....................................
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in
the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the
solicitation.
SPECIFICATION
DEPARTMENT OF DEFENSE
MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.
STANDARDS
DEPARTMENT OF DEFENSE
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard for Microcircuit Case Outlines.
HANDBOOKS
DEPARTMENT OF DEFENSE
MIL-HDBK-103 - List of Standard Microcircuit Drawings (SMD's).
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in
accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as
designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class.
Therefore, the tests and inspections herein may not be performed for the applicable device class (see MIL-PRF-38534).
Furthermore, the manufacturer may take exceptions or use alternate methods to the tests and inspections herein and not
perform them. However, the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device
class.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38534 and herein.
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
+16 V dc to +40 V dc
-55
q
C to +125
q
C
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
SIZE
A
REVISION LEVEL
5962-93068
SHEET
C
3
DSCC FORM 2234
APR 97
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full specified operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked
with the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked in MIL-HDBK-103 and
QML-38534.
3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described
herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot
sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for
those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer
and be made available to the preparing activity (DSCC-VA) upon request.
3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this
drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturer's product meets
the performance requirements of MIL-PRF-38534 and herein.
3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of
microcircuits delivered to this drawing.
4. QUALITY ASSURANCE PROVISIONS
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as
modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the
form, fit, or function as described herein.
4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply:
a.
Burn-in test, method 1015 of MIL-STD-883.
(1)
Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit
shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent
specified in test method 1015 of MIL-STD-883.
T
A
as specified in accordance with table I of method 1015 of MIL-STD-883.
(2)
b.
Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
SIZE
A
REVISION LEVEL
5962-93068
SHEET
C
4
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics.
Test
Symbol
Conditions 1/
-55
G
C
d
T
C
d
+125
G
C
V
IN
= 28V dc ±0.5V
no external sync, C
L
= 0
unless otherwise specified
I
OUT
= 5.0 A dc
Group A
subgroups
Device
types
Min
1
2,3
L, R
Output current
I
OUT
V
IN
= 16 V dc to 40 V dc
L, R
V
OUT
ripple voltage
V
RIP
I
OUT
= 5.0 A
BW = 10 kHz to 2 MHz
1,2,3
1,2,3
1,2,3
1
2,3
L, R
V
OUT
line regulation
VR
LINE
V
IN
: 16 V dc to 40 V dc
I
OUT
= 5.0 A
L, R
V
OUT
load regulation
VR
LOAD
I
OUT
= 0 to 5.0 A
L, R
Input current
I
IN
I
OUT
= 0 A,
Inhibit (pin 2) = 0
L, R
I
OUT
= 0 A,
Inhibit (pin 2) = open
L, R
I
IN
ripple current
I
RIP
I
OUT
= 5.0 A,
BW = 10 kHz to 10 MHz
L, R
See footnotes at end of table.
1,2,3
1,2,3
02
01,02
02
01, 02
02
01,02
01,02
4.95
4.85
4.7
Limits
Unit
Max
5.05
5.15
5.3
5000
5000
50
90
180
50
mV
mVp-p
mA
V dc
Output voltage
V
OUT
1,2,3
1,2,3
1,2,3
1,2,3
02
01,02
02
01,02
100
50
100
8
mA
mV
1,2,3
1, 2, 3
02
01,02
10
75
1,2,3
1, 2, 3
02
01,02
175
50
mAp-p
1,2,3
02
65
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
SIZE
A
REVISION LEVEL
5962-93068
SHEET
C
5
DSCC FORM 2234
APR 97
京公网安备 11010802033920号
EEWORLD
