EEWORLDEEWORLDEEWORLD

Part Number

Search

28110.201.011

Description
Wire Terminal, 1.5mm2
CategoryThe connector    terminals   
File Size23KB,1 Pages
ManufacturerLear Corporation
Download Datasheet Parametric View All

28110.201.011 Overview

Wire Terminal, 1.5mm2

28110.201.011 Parametric

Parameter NameAttribute value
Reach Compliance Codeunknown
ECCN codeEAR99
Manufacturer's serial number28110
terminal genderFEMALE
Terminal and terminal strip typesWIRE TERMINAL
Conductor cross section1.5 mm2
Base Number Matches1
Characteristics and dimensions of terminals
Part number
Specification
Material
Surface / Colour
Form
Transport
Single part
Packing unit / piece
Section area (mm
2
)
Tab thickness (mm)
Tab width (mm)
DIN
Nominal size
Material thickness (mm)
Notch
a
1
a
2
l
1
l
2
l
3
28110.201.011
Receptacle
CuSn
Sn 3
Chain form
Longitudinal transport
X
7000
0.75-1.50
0.80
6.30
46247 Teil 3
6.3-1.5
0.44
x
8.50
4.50
19.20
7.40
4.00
Note: The drawing only gives an overview of the geometry of the part. The crimp area is shown as
supplied in strip form. A technical drawing is available on request.
Contents of your inquiry
Packing Units (per 7000 pieces)
0
CW
Reset
Collect for inquiry
Testing a battery-powered product with a 26K resistor between the battery pads (no battery is soldered at this time!),...
Testing a battery-powered product, there is a 26K resistor between the two ends of the battery pad (no battery is soldered at this time!), what is the internal resistance of the board power supply cir...
QWE4562009 Test/Measurement
I don't understand some parameters of Mosfet
The MOSFET driver circuit chip IR2110 has an output current of about 2A. Is this the drive current? The output voltage is 10-20V. So the output power of the tube is IU, or how to calculate it? Then th...
西里古1992 Analog electronics
consult
[i=s]This post was last edited by paulhyde on 2014-9-15 09:41[/i] In addition to preparing analog-to-digital and digital-to-analog conversion modules, the minimum system of the microcontroller, and bu...
liu5013 Electronics Design Contest
Urgent! ! About the interrupt priority of dsp28027
Urgent! ! About the interrupt priority of dsp28027...
huangyiqian1000 DSP and ARM Processors
Regarding the program issues of AT24C02B
Why is my display always zero, please take a look. The following is my program: #include "reg52.h" #include "absacc.h" #include "math.h" #define uchar unsigned char #define uint unsigned int # dm XBYT...
zcx027 Embedded System
Wince read and write mmc device problem, experts please help.
I have a ca card, mmc interface on winxp, connected to a usb card reader, drive letter H: I use createfile("\\\\.\\H:",...); It can operate normally, reset, read, write are all normal. Write a command...
chenjing1986 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 394  1375  25  2287  2650  8  28  1  47  54 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号