EEWORLDEEWORLDEEWORLD

Part Number

Search

GUB-GL8B-01-2803-D-D

Description
Array/Network Resistor, Bussed, Thin Film, 0.1W, 280000ohm, 0.5% +/-Tol, -100,100ppm/Cel, 4430,
CategoryPassive components    The resistor   
File Size493KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

GUB-GL8B-01-2803-D-D Overview

Array/Network Resistor, Bussed, Thin Film, 0.1W, 280000ohm, 0.5% +/-Tol, -100,100ppm/Cel, 4430,

GUB-GL8B-01-2803-D-D Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid795629551
package instructionSMT, 4430
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL7.2
structureMolded
Network TypeBussed
Number of terminals16
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height2.667 mm
Package length11.176 mm
Package formSMT
Package width7.544 mm
Rated power dissipation(P)0.1 W
resistance280000 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesGUB
size code4430
technologyTHIN FILM
Temperature Coefficient100 ppm/°C
Tolerance0.5%
TaNFilm
®
Small Outline Surface
Mount Resistor Network
GUB Series
Thin film on ceramic technology
0.220” and 0.300” sizes available
RoHS compliant version available
DESC 87012 and 87013 available
Standard JEDEC packages for automatic placement equipment
Compliant leads to
compensate for
thermal expansion
and contractions.
IRC Advanced Film Division
Ultra precision tantalum
nitride resistance element
on high purity alumina.
Rugged, molded
construction.
IRC’s TaNFilm®, Small Outline Integrated Circuit resistor networks are ideally suited for surface mounting.
The 0.05 inch lead spacing provides higher lead density, increased component count, lower installed resistor
cost, and better reliability. They are ideally suited for the latest surface mount assembly techniques, and each
lead can be 100% visually inspected. The compliant leads relieve thermal expansion and contraction stressed
created by soldering and temperature excursions.
The tantalum nitride film system provides precision tolerance, exceptional TCR tracking, and low noise.
TaNFilm® provides stability, high reliability, and long life characteristics. Testing has demonstrated performance
exceeding MIL-PRF-83401 characteristics H.
Electrical Data
GM Type
Resistance Range (Ω)
GL Type
Absolute Tolerance
Ratio Tolerance To R1
TCR (ppm/°C)
TCR Tracking To R1 (ppm°C)
Operating Temperature Range
Noise
Substrate
Custom circuits and special testing available.
Schem A: 10 to 200K
Schem B: 10 to 1000K
Schem A: 10 to 150K
Schem B: 10 to 75K
Available to ±0.1%
Available to ±0.05%
±25, ±50, ±100
±5
-55°C to +125°C
Less than -25 dB
High purity alumina substrate
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
GUB Series Issue November 2008 Sheet 1 of 3
How to use a single-chip computer to detect the power-on and power-off time of a PC
How to use a microcontroller to detect the power on and off time of a PC? Is there any good solution?...
bobo_cuckoo Embedded System
LTC3105 will not start
Have you guys used this chip? Its AUX pin needs to charge C2 first, and the chip can only start after it reaches 1.4V. However, when I charged it, I found that the capacitor could not reach 1.4V. What...
朝朝暮暮朝朝 Analog electronics
Emergency SOS Expert
I have a small software, I want to install it in the startup, turn on the machine, the software will start automatically, or after installing this software on the notebook, the software will run autom...
a8190182 Embedded System
Please tell me whether the P0 port of stc12c5a60s2 needs to be connected to a pull-up resistor
I would like to ask the experts who have used the stc12c5a60s2 microcontroller. I saw some information saying that the stc12c5a60s2 P0 port does not need to be connected to a pull-up resistor. I am no...
koenlee93 51mcu
How to clean the board
Let me discuss a problem with you.I used a lot of rosin when soldering the SMD components, so the area near the SMD components is hard to see. I used alcohol to clean it, but some of the words on the ...
sjl2001 PCB Design
What are the differences between USB Function and USB Host controller drivers?
As the title says, please advise sincerely...
beifenggood Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 803  1172  1278  2815  1144  17  24  26  57  18 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号