ALUMINUM ELECTROLYTIC CAPACITORS
WP
5.5mmL Chip Type, Bi-Polarized
series
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
WP
Smaller
Specifications
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan
δ)
ZP
Performance Characteristics
–40 to +85°C
6.3 to 50V
0.1 to 100µF
±20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.05CV or 10 (µA) ,whichever is greater.
Measurement frequency : 120Hz at 20°C
Rated voltage (V)
tan
δ
(MAX.)
6.3
0.24
10
0.20
6.3
4
8
16
0.17
10
3
6
25
0.17
16
2
4
25
2
4
35
0.15
35
2
3
50
0.15
50
2
3
Measurement frequency : 120Hz
Stability at Low Temperature
Rated voltage (V)
Z– 25°C / Z+20°C
Impedance ratio
ZT / Z20 (MAX.)
Z– 40°C / Z+20°C
Endurance
The specifications listed at right shall be met
when the capacitors are restored to 20°C after the
rated voltage is applied for 1000 hours at 85°C
with the polarity inverted every 250 hours.
Capacitance change
tan
δ
Leakage current
Within ±20% of the initial capacitance value
200% or less than the initial specified value
Less than or equal to the initial specified value
Shelf Life
Resistance to soldering
heat
Marking
After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which
Within ±10% of the initial capacitance value
Capacitance change
is maintained at 250°C. The capacitors shall meet the
Less than or equal to the initial specified value
tan
δ
characteristic requirements listed at right when they are
Less than or equal to the initial specified value
Leakage current
removed from the plate and restored to 20°C.
Black print on the case top.
Chip Type
0.5 MAX.
Capacitance
Lot No.
Voltage
Plastic platform
0.3 MAX.
Type numbering system (Example : 16V 10
µ
F)
1
2
3
4
5
6
7
8
9 10 11 12 13 14
C±0.2
UWP 1 C 1 0 0 M C L 1 G B
A±0.2 A±0.2
Taping code
Configuration
Capacitance tolerance (±20%)
A2
10
16V
φD±0.5
B±0.2
5.4
Voltage mark for 6.3V is
6V .
+0.1
–0.2
E
0.5 to 0.8
φD
Dimensions
V
A
B
C
E
4
1.8
4.3
4.3
1.0
5
2.1
5.3
5.3
1.3
(mm)
6.3 8
2.4 3.3
6.6 8.3
6.6 8.3
2.2 2.3
Rated capacitance (10µF)
Rated voltage (16V)
Series name
Type
Cap. (µF)
Code
6.3
0J
10
1A
16
1C
25
1E
35
1V
4
4
4
4
4
5
5
6.3
8
50
1H
1.0
2.0
2.8
4.0
8.4
13
17
20
36
Allowable
ripple
Rated
ripple
0.1
0.22
0.33
0.47
1
2.2
3.3
4.7
10
22
33
47
100
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
5
6.3
6.3
8
28
37
45
82
4
6.3
6.3
8
17
33
41
61
4
5
6.3
6.3
8
12
23
37
49
75
5
5
6.3
8
8
12
16
27
50
61
4
5
5
6.3
8
8.4
16
18
29
54
Case size
φ
D (mm)
Rated ripple current (mArms) at 85°C 120Hz
Frequency coefficient of rated ripple current
Frequency
Coefficient
50 Hz
0.70
120 Hz
1.00
300 Hz
1.17
1 kHz
1.36
10 kHz or more
1.50
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in page 18, 19.
Please select UN(p.162) series if high C/V products are reqired.
Please refer to page 3 for the minimum order quantity.
CAT.8100D
Analog electronics
京公网安备 11010802033920号
EEWORLD
