88903-107LF datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > The connector> 88903-107LF

88903-107LF: DescriptionHigh Speed / Modular Connectors 5ROW STRT SIGNAL HDR PRESS-FIT; CategoryThe connector; File Size46KB，9 Pages; ManufacturerFCI [First Components International]

Download Datasheet Parametric View All

88903-107LF Online Shopping

Suppliers	Part Number	Price	MOQ	In stock
	88903-107LF	-	-	View	Buy Now

88903-107LF Overview

High Speed / Modular Connectors 5ROW STRT SIGNAL HDR PRESS-FIT

88903-107LF Parametric

Parameter Name	Attribute value
Product Attribute	Attribute Value
Manufacturer	FCI [First Components International]
Product Category	High Speed / Modular Connectors
RoHS	Details
Product	Headers
Number of Positions	60 Position
Number of Rows	5 Row
Pitch	2 mm
Termination Style	Through Hole
Minimum Operating Temperature	- 55 C
Maximum Operating Temperature	+ 125 C
Packaging	Tube
Current Rating	1 A
Housing Material	Liquid Crystal Polymer (LCP)
Mounting Angle	Straight
Contact Material	Phosphor Bronze
Insulation Resistance	5 GOhms
Factory Pack Quantity	24

Preview

Download Datasheet

View All

NUMBER

TYPE

GS-12-180

TITLE

PRODUCT SPECIFICATIONS

PAGE

REVISION

Converged Metral® Header

1 of 9

AUTHORIZED BY

DATE

9 Oct 07

D. Horchler

STATUS

UNRESTRICTED

1.0

OBJECTIVE

This specification defines the performance, test, quality and reliability requirements of the Converged

Metral Header product.

2.0

SCOPE

This specification is applicable to the termination characteristics of the Converged Metral Header which

provides a separable interconnect for printed circuit boards.

3.0

GENERAL

This document is composed of the following sections:

Paragraph

1.0

2.0

3.0

4.0

5.0

5.1

5.2

5.3

5.4

6.0

7.0

8.0

9.0

9.1

9.2

9.3

9.4

9.5

9.6

TABLE 1

3.1

Title

OBJECTIVE

SCOPE

GENERAL

APPLICABLE DOCUMENTS

REQUIREMENTS

Qualification

Material

Finish

Design and Construction

ELECTRICAL CHARACTERISTICS

MECHANICAL CHARACTERISTICS

ENVIRONMENTAL CONDITIONS

QUALITY ASSURANCE PROVISIONS

Equipment Calibration

Inspection Conditions

Sample Quantity and Description

Acceptance

Qualification Testing

Requalification Testing

QUALIFICATION TEST SEQUENCE MATRIX

Banned/Restricted Substances

All product where the part number ends in ‘LF’ meet the European Union directives and other

country regulations as described in GS-22-008. The part numbers that do not end in ‘LF’ meet all

regulations except for Pb in SnPb plating.

3.2

Manufacturing Processability

All products covered by this specification except those with part number containing ‘-N’ will

withstand exposure to 260°C for 60 seconds in a convection, infra-red or vapor phase reflow oven.

Part numbers with ‘-N’ will not withstand reflow and the Au contact surface of the contacts shall be

exposed to a maximum of 140°C for no longer than 15 seconds in a wave solder operation.

PDS: Rev :G

Form E-3334

Rev F

FCI

STATUS:Released

Printed: Aug 22, 2011

GS-01-001

NUMBER

TYPE

GS-12-180

TITLE

PRODUCT SPECIFICATIONS

PAGE

REVISION

Converged Metral® Header

5 of 9

AUTHORIZED BY

DATE

9 Oct 07

D. Horchler

STATUS

UNRESTRICTED

6.8

Characteristic Impedance - The specification requirement shall be satisfied when evaluated in

accordance with FCI Test Specification BUS-03-110 and the following details:

Specification requirement 55 Ohms +/- 5 Ohms single ended except where column 6 is not

bounded by the shield of a neighboring module. In this case the unshielded end column shall

have a requirement of 61 +/- 5 Ohms single ended.

Sample documentation

Sample test conditions @ 500ps ( 10 - 90% ) risetime with all lines terminated in their

characteristic impedance

6.9

Crosstalk – Adjacent active/quiet near end cross talk shall not exceed 5% in any row or column

combination. The far end cross talk shall not exceed 2.5%. The specification requirement shall be

satisfied when evaluated in accordance with FCI Test Specification BUS-03-108 and the following

details:

Connectors shall be mated.

Measurements shall be made from tail tip to tail tip.

Test condition: 1 ns rise time pulse (0.0V to 2.0V) with a 50 –ohm termination.

Measurement equipment: Sampler/Pulse Generator/Scope equipment with a 50 ohm reference

impedance.

7.0

MECHANICAL CHARACTERISTICS

7.1

Contact Retention to Housing- There shall be no loosening of the contact or damage to the contact

or damage to the connector when a axial force of 10N is applied to a contact in either direction

along the axis of retention, when measured in accordance with EIA-364-29.

Total mating force- The total force to mate a male header with Metral receptacle header shall not

exceed 0.45N for signal or 1.5N for power times the number of contacts, when measured in

accordance with EIA-364-13.

Header Pin Insertion/Retention Force - The force required to insert header with compliant pins into

plated through holes in a printed circuit board at a rate of 0.5 inches/minute shall not exceed 65 N

per pin. The retention force in an axial direction opposite that of insertion shall not be less than 20

N per pin after 3 insertion/extraction cycles on the same holes.

PCB Hole Deformation Radius - Cross-section parallel to board surface. Photograph and measure

the hole deformation (deformation on board material) radius at a point 0.010" from the surface, and

at the center of the compliant pin section. Include 10 holes. The average (of 10 holes) hole

deformation radius shall be no greater than 0.0381 mm (0.0015 in.) when measured from the

drilled hole. The absolute maximum deformation radius shall not exceed 0.0508 mm (0.002 in ).

Reference MIL-STD-2166.

7.2

7.3

7.4

7.5

PDS: Rev :G

Form E-3334

Rev F

FCI

PCB Hole Wall Damage - Cross-section perpendicular to the board surface, and through the

compliant section wear track. Photograph and measure the copper thickness remaining between

the compliant pin and the printed wiring board laminate. Include 10 holes. The minimum average

(of 10 holes) copper thickness remaining between the compliant pin and the printed wiring board

STATUS:Released

Printed: Aug 22, 2011

laminate shall not be less than 0.00762 mm (0.0003 in. ). In addition there shall be no copper

GS-01-001

Recommended Resources

Touch delay switch power supply circuit

Small improved circuit of hanging electronic watch

Basic application circuit diagram of LM2931

Two-line intercom telephone circuit diagram

Stable sine wave oscillator

Charging a single 4.2V Li-ion battery using the LTC732 as a controller

I should be happy that the photosensitive resin 3D printer is finished, but why do I feel like I'm running like crazy?: [i=s]This post was last edited by cardin6 on 2017-9-8 18:40[/i] I have been making this machine intermittently (I won’t post pictures of the machine yet). Finally, the test is completed, but why don’t...; cardin6 Creative Market

There is an error in calling the external program, please give me some advice!: I want to call an external program through a button event, but there is always an error code as follows Private Sub Button3_Click(ByVal sender As System.Object, ByVal e As System.EventArgs) Handles Bu...; 帐单 Embedded System

Study summary: Friendly Arm mini2440 boot mode address mapping and program writing: The mini2440 development board has two startup modes, one is to start from Nor Flash, the other is to start from Nand Flash.When we started to learn to write an assembly program for LED key query buzz...; Hellovictoria Embedded System

I would like to ask a question about reading and writing EEPROM on the I2C bus: What details should I pay attention to when reading and writing EEPROM? My EEPROM is written according to the timing diagram. I write data in and read it out. There is no problem with bit operations. ...; sujd_01 Embedded System

The error "has EABI version 5, but target u-boot has EABI version 0" suddenly appears when compiling u-boot: The S5pv210 uboot has been compiled for a long time, and some gui functions have been added recently, but the compilation actually has the following error, why? ! /usr/local/arm/arm-2009q3/bin/arm-non...; Wince.Android Embedded System

Does anyone have the mini_pci_e package?: I was going to use the board for my graduation project, but I saw there was no interface, so I had to make a board myself -- Goldfinger:) Can anyone give me one? Otherwise, it's still very troublesome...; 小强电子爱好者 stm32/stm8

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components