Max. 6ms (Approx. 3ms) [Max. 10ms (Approx. 5ms)] (Nominal operating voltage applied to
the coil, excluding contact bounce time.) (without diode)
Min. 200 m/s
2
{20 G} (Half-wave pulse of sine wave: 11ms; detection time: 10µs.)
Min. 1,000m/s
2
{100 G} (Half-wave pulse of sine wave: 6ms.)
10 to 55 Hz at double amplitude of 3mm (Detection time: 10µs.)
10 to 55 Hz at double amplitude of 5mm
Min. 5×10
6
(at 180 cpm)
Min. 10
5
(10W 2.5 GHz, Impedance 50Ω, V.S.W.R. 1.2)
Min. 3×10
5
(10mA 24V DC resistive load)
Ambient temperature: –40°C to +70°C
–40°F to +158°F
Humidity: 5 to 85% R.H. (Not freezing and condensing at low temperature)
Approx. 5 g
.18 oz
Rating
High frequency
characteristics
(Initial) (~2.5GHz,
Impedance 50Ω)
Electrical
characteristics
Temperature rise (at 20°C)
Operate time [Set time] (at 20°C)
Release time [Reset time] (at 20°C)
Shock
resistance
Vibration
resistance
Mechanical
Functional
Destructive
Functional
Destructive
Mechanical
characteristics
Expected life
Conditions
Unit weight
Electrical
Conditions for operation, transport and storage*
Note: * The upper operation ambient temperature limit is the maximum temperature that can satisfy the coil temperature rise value. Refer to [6] AMBIENT ENVIRONMENT
in GENERAL APPLICATION GUIDELINES.
Panasonic Corporation
Automation Controls Business Unit
industrial.panasonic.com/ac/e
ASCTB74E 201201-T
RX (ARX)
REFERENCE DATA
1. High frequency characteristics
Sample: ARX1012
Measuring method: Measured with HP network analyzer (HP8753C).
The details for the high frequency characteristics and the measurement
procedures and conditions are listed in the RX relay test report.
• V.S.W.R. (Return loss)
0
5.0
Insertion loss, dB
Return loss, dB
10
COM-NO
1.2
1.1
30
COM-NC
40
0.4
80
COM-NO
2.0
1.5
20
V.S.W.R.
COM-NC
0.1
Isolation, dB
20
• Insertion loss
0
• Isolation
0
0.2
COM-NO
0.3
40
COM-NC
60
50
300kHz
1.5GHz
Frequency
2.5GHz 3GHz
0.5
300kHz
1.5GHz
Frequency
2.5GHz3GHz
100
300kHz
1.5GHz
Frequency
2.5GHz 3GHz
DIMENSIONS
(mm
inch)
CAD Data
The CAD data of the products with a
CAD Data
mark can be downloaded from: http://industrial.panasonic.com/ac/e
PC board pattern (Bottom view)
20.5
.807
12.4
.488
2.54
.100
0.9 dia hole
.035 dia hole
(2 coil latching type only)
9.2
.362
0.2
.008
2.63
.104
2.54
.100
3.0
.118
(2.04)
(.080)
7.62
.300
(2.74)
(.108)
7.62
.300
R
0.90
.035
0.
45
2-0.6×0.3
2-.024×.012
Tolerance:
±0.1
±.004
General tolerance:
±0.3
±.012
Solder to the PC board earth.
Schematic (Bottom view)
7-0.40 to 0.45 dia.
7-.016 to .018 dia.
Direction indication
Single side stable
Direction indication
1
7
1 coil latching
Direction indication
1
7
2 coil latching
1
6
7
14 13 12 11 10 9
NC
COM
8
14 13 12 11 10 9
RESET
COM
8
14 13 12 11 10 9
RESET
COM
8
NO
SET
SET
(Deenergized condition)
(Reset condition)
(Reset condition)
ASCTB74E 201201-T
Panasonic Corporation
Automation Controls Business Unit
industrial.panasonic.com/ac/e
RX (ARX)
NOTES
1. Coil operating power
Pure DC current should be applied to the
coil. The wave form should be
rectangular. lf it includes ripple, the ripple
factor should be less than 5%.
However, check it with the actual circuit
since the characteristics may be slightly
different. The nominal operating voltage
should be applied to the coil for more
than 30 ms to set/reset the latching type
relay.
2. Coil connection
When connecting coils, refer to the wiring
diagram to prevent mis-operation or
malfunction.
3. External magnetic field
Since RX relays are highly sensitive
polarized relays, their characteristics will
be affected by a strong external magnetic
field. Avoid using the relay under that
condition.
4. Cleaning
For automatic cleaning, the boiling
method is recommended. Avoid
ultrasonic cleaning which subjects the
relays to high frequency vibrations, which
may cause the contacts to stick.
lt is recommended that a fluorinated
hydrocarbon or other alcoholic solvents
be used.
5. Soldering
The manual soldering shall be performed
under following condition.
Max. 260°C
500°F
10s
Max. 350°C
662°F
3s
In addition, when soldering the case to
the PC board, the plating may swell
depending on the soldering conditions.
6. Conditions for operation, transport
and storage conditions
1) Ambient temperature, humidity, and
atmospheric pressure during usage,
transport, and storage of the relay:
(1) Temperature:
–40 to +70°C
–40 to +158°F
(2) Humidity: 5 to 85% RH
(Avoid freezing and condensation.)
The humidity range varies with the
temperature. Use within the range
indicated in the graph below.
(3) Atmospheric pressure: 86 to 106 kPa
Temperature and humidity range for
usage, transport, and storage:
Humidity, %RH
4) Low temperature, low humidity
environments
The plastic becomes brittle if the relay is
exposed to a low temperature, low
humidity environment for long periods of
time.
7. Latching relay
In order to assure proper operating
regardless of changes in the ambient
usage temperature and usage conditions,
nominal operating voltage should be
applied to the coil for more than 30 ms to
set/reset the latching type relay.
For general cautions for use, please
refer to the “General Application
Guidelines”.
;;;;;;;;;
;;;;;;;;;;
;;;;;;;;;;
;;;;;;;;;;
;;;;;;;;;;
;;;;;;;;;;
;;;;;;;;;;
85
Tolerance range
(Avoid freezing
when used at
temperatures lower
than 0°C
32°F
5
(Avoid
condensation
when used at
temperatures higher
than 0°C
32°F
–40
–40
0
+32
Temperature,
°C
°F
70
+158
2) Condensation
Condensation forms when there is a
sudden change in temperature under
high temperature and high humidity
conditions. Condensation will cause
deterioration of the relay insulation.
3) Freezing
Condensation or other moisture may
freeze on the relay when the temperature
is lower than 0°C
32°F.
This causes
problems such as sticking of movable
parts or operational time lags.
Panasonic Corporation
Automation Controls Business Unit
industrial.panasonic.com/ac/e
ASCTB74E 201201-T
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Hello everyone, I want to port the T9 input method to the wince4.2 platform recently, but I don't know how to do it. There are many source codes for input methods on the Internet, but I don't know if ...
Regarding the problem that the pspice simulation comparator cannot work properly: I recently found that when using pspice simulation, such as LM339 comparator, the simulation results are different fro...
I want to amplify the sound signal collected by the electret microphone. What kind of amplifier and filter circuit do I need? Please provide a circuit reference! ! !...
[color=#222222][backcolor=rgb(238, 238, 238)][font=sans-serif][Ask an expert for an answer] Why can't the MSP430 compilation environments CCS5 and IAR be used at the same time? [/font][/backcolor][/co...
introduction
In the discharge process of tokamak plasma physics, the study of rupture and sawtooth is of great significance. Rupture and sawtooth exist in most tokamaks. Rupture is a notew...[Details]
I. Introduction
Since RS232 has a short communication distance (only 15 meters according to EAT/TAI-232 standard), and can only perform point-to-point communication, it cannot directly f...[Details]
LED lamps and bulbs are now rapidly replacing incandescent, halogen and CFL (compact fluorescent lamp) light sources in many general lighting applications. Flyback DC/DC converters are the power su...[Details]
Digital array radar (DAR) uses digital beam forming (DBF) in both receiving and transmitting modes to achieve flexible distribution and reception of RF signal power in the airspace, obtain excellent t...[Details]
TC9012F is a universal CMOS large-scale integrated circuit for infrared remote control signal transmission, suitable for remote control of TV, VTR, laser player and other equipment. In the market, ...[Details]
hint:
The number of speakers and their spacing limit the sound field of a portable stereo system.
Spatial audio attempts to artificially recreate the experience of listening to sounds i...[Details]
1 Basic Features
In computer control systems and various intelligent instruments and meters composed of single-chip microcomputers (or microprocessors), various external analog signals must be ...[Details]
At present, how various communication technologies will evolve after 3G is a focus of great concern in the industry. Especially for TD-SCDMA, whether it can achieve smooth evolution to the next gen...[Details]
1 Introduction to LED
With the development of science and technology, people have higher and higher requirements on automobile light sources. LED (Light Emitting Diode) has gradually attracted...[Details]
In order to prevent the lithium battery from being damaged by abnormal conditions such as overcharge, over discharge, and overcurrent, a lithium battery protection device is usually used to prevent...[Details]
1. Tips for charging UPS for the first time
After purchasing a new UPS, plug the UPS into the 220V mains power grid and charge it for at least 12 hours to ensure that the battery is fully char...[Details]
1 Introduction
Lijia'an Yellow River Diversion Culvert is a large gravity diversion gate in the lower reaches of the Yellow River. The Yellow River Diversion Culvert is located in Lijia'an Vi...[Details]
Traditionally, when using PLC to control stepper motors, a dedicated stepper motor control intelligent module is usually added to the PLC, and then connected to the drive power supply to realize th...[Details]
In some motion control systems with simple control or low cost requirements, stepper motors are often used as actuators. The biggest advantage of stepper motors in such applications is that they ca...[Details]
The circuit has overcharge protection, over-discharge protection, over-current protection and short-circuit protection functions. Its working principle is analyzed as follows:
1 Normal state
...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
