refer to our Tape and Reel Packaging Specification
Brochure, BRD8011/D.
**These packages are inherently PB--Free.
Publication Order Number:
P6KE200B/D
April, 2006 - Rev. 1
-
1
P6KE200B
MAXIMUM RATINGS
Rating
Peak Power Dissipation (Note 1) @ T
L
≤
25°C
Steady State Power Dissipation
@ T
L
≤
75°C, Lead Length = 3/8″, Derated above T
L
= 75°C
Thermal Resistance Junction--to--Lead
Forward Surge Current (Note 2) @ T
A
= 25°C
Operating and Storage Temperature Range
Symbol
P
PK
P
D
R
θJL
I
FSM
T
J
, T
stg
Value
600
5.0
50
15
100
-- 55 to +150
Unit
W
W
mW/°C
°C/W
A
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. Nonrepetitive current pulse per Figure 3 and derated above T
A
= 25°C per Figure 2.
2. 1/2 sine wave (or equivalent square wave), PW = 8.3 ms, duty cycle = 4 pulses per minute maximum.
ELECTRICAL CHARACTERISTICS
(T
A
= 25°C unless
otherwise noted, V
F
= 3.5 V Max. @ I
F
(Note 3) = 50 A)
Symbol
I
PP
V
C
V
RWM
I
R
V
BR
I
T
ΘV
BR
I
F
V
F
Parameter
Maximum Reverse Peak Pulse Current
Clamping Voltage @ I
PP
Working Peak Reverse Voltage
Maximum Reverse Leakage Current @ V
RWM
Breakdown Voltage @ I
T
Test Current
Maximum Temperature Coefficient of V
BR
Forward Current
Forward Voltage @ I
F
V
C
V
BR
V
RWM
I
F
I
I
R
V
F
I
T
V
I
PP
Uni-
-Directional TVS
ELECTRICAL CHARACTERISTICS
(T
A
= 25°C unless otherwise noted, V
F
= 3.5 V Max. @ I
F
(Note 3) = 50 A)
V
RWM
(Note 4)
V
171
Breakdown Voltage
I
R
@ V
RWM
mA
5
V
BR
Min
190
(Note 5)
(Volts)
Nom
200
Max
210
@ I
T
mA
1
V
C
@ I
PP
(Note 6)
V
C
V
274
I
PP
A
2.2
ΘV
BR
%/°C
0.108
Device
P6KE200B
Device
Marking
P6KE200B
3. 1/2 sine wave (or equivalent square wave), PW = 8.3 ms, duty cycle = 4 pulses per minute maximum.
4. A transient suppressor is normally selected according to the maximum working peak reverse voltage (V
RWM
), which should be equal to or
greater than the DC or continuous peak operating voltage level.
5. V
BR
measured at pulse test current I
T
at an ambient temperature of 25°C.
6. Surge current waveform per Figure 3 and derate per Figures 1 and 2.
http://onsemi.com
2
P6KE200B
NONREPETITIVE PULSE
WAVEFORM SHOWN IN
FIGURE 3
PEAK PULSE DERATING IN % OF
PEAK POWER OR CURRENT @ T = 25 C
A
_
100
PPK , PEAK POWER (kW)
10
100
80
60
40
20
0
0
25
50
75
100 125 150 175
200
1
0.1
0.1
ms
1
ms
10
ms
100
ms
1 ms
10 ms
t
P
, PULSE WIDTH
T
A
, AMBIENT TEMPERATURE (_C)
Figure 1. Pulse Rating Curve
Figure 2. Pulse Derating Curve
t
r
≤
10
ms
100
VALUE (%)
PEAK VALUE -- I
PP
PULSE WIDTH (t
p
) IS
DEFINED AS THAT
POINT WHERE THE
PEAK CURRENT
DECAYS TO 50% OF I
PP
.
I
PP
2
PD, STEADY STATE POWER DISSIPATION (WATTS)
3/8″
5
4
3
2
1
0
0
25
50
75 100 125 150 175
T
L
, LEAD TEMPERATURE
_C)
200
3/8″
HALF VALUE --
50
t
P
0
0
1
2
3
t, TIME (ms)
4
Figure 3. Pulse Waveform
Figure 4. Steady State Power Derating
http://onsemi.com
3
P6KE200B
PACKAGE DIMENSIONS
AXIAL LEAD
CASE 59AA--01
(Previously 59--09)
ISSUE O
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. ALL RULES AND NOTES ASSOCIATED WITH
JEDEC DO--41 OUTLINE SHALL APPLY.
4. POLARITY DENOTED BY CATHODE BAND.
5. LEAD DIAMETER NOT CONTROLLED WITHIN
F DIMENSION.
6. REPLACES CASE 59--09.
DIM
A
B
D
K
INCHES
MIN
MAX
0.228 0.299
0.102 0.142
0.028 0.034
1.000
------
MILLIMETERS
MIN
MAX
5.80
7.60
2.60
3.60
0.71
0.86
25.44
------
B
K
D
A
K
SURMETIC is a trademark of Semiconductor Components Industries, LLC.
ON Semiconductor
and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer
purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support:
800--282--9855 Toll Free
Literature Distribution Center for ON Semiconductor
USA/Canada
P.O. Box 61312, Phoenix, Arizona 85082--1312 USA
Phone:
480--829--7710 or 800--344--3860 Toll Free USA/Canada
Japan:
ON Semiconductor, Japan Customer Focus Center
2--9--1 Kamimeguro, Meguro--ku, Tokyo, Japan 153--0051
Fax:
480--829--7709 or 800--344--3867 Toll Free USA/Canada
The creative USB bracelet is made of soft and flexible silicone material and can be creatively matched with a variety of colors. The length of the bracelet can be printed in one to three colors, which...
[i=s]This post was last edited by flyriz on 2020-4-23 19:58[/i]Hello everyone, as shown below:An AC input signal is input to the input end of a voltage follower circuit and an amplifier circuit. The p...
The DCDC circuit design in the figure below has an input of 20-36V and is required to output 19.5V. When the current reaches more than 350mA, the voltage drops to about 10V.
The input power supply is ...
When I was a kid, I watched a movie called "Back to the Future", in which you can ride a super cool time machine to travel between the present and the future. At that time, I thought it would be reall...
Creative Market
京公网安备 11010802033920号
EEWORLD
