PAK 50E connectors and 3M™ 3365 Cable can be accomplished when using the 3M™
3443-128 Series Locator Plate and the 3M™ 3640 or 3335 Assembly Press.
Tools required:
Product #
3443-128
3640
3335
3436-1J
3442-126
Description
Locator Plate
Assembly Press
Assembly Press
Shut Height Gage
Platen
Stock Number
80-4000-1626-9
80-6100-7882-8
80-6100-3208-0 (alternate to the 3640)
78-8118-0908-2
80-6104-7838-2
PAK 50E Connector
PAK 50E
Cover 2
Cover 1
Assembly Press Setup
1. The 3M
™
3436-1J Shut Height Gauge was
shipped with the locator plate. The setting height
is inscribed on the side of the gauge. The setting
of 18 1/2 is for the 3M
™
3640 Press and the
setting of 19 is for the 3M
™
3335 Press.
2. Place the shut height gauge on the base of the
press and bring down the shaft of the press onto
the surface of the shut height gauge lightly.
Adjust the shaft length by turning the adjusting
knob on the top of the shaft (3640) or the
adjusting collar on the lower portion of the shaft
of the press (3335) so that the press handle comes
completely down with only a small amount of
pressure from the press shaft on the shut height
gauge. On the 3335 only, tighten the locking
collar. The shut height distance is now set.
3. Place the 3M
™
3442-126 Platen on the end of the
press shaft and lock it in place by sliding the
holding clamp on the platen into the groove on
the press shaft. Your assembly press is now
setup.
Note: The 3640 in the picture is shown with the
separately purchased
3M
™
3771 Base Plate which
adds stabilization to the press. It’s use is optional.
The 3335 Heavy Duty press is also applicable, but
not shown.
Shut
height
gage
3436-1J
3771 Base Plate
Assembly Press Setup
Locator Plate Setup
1. The 3M
™
PAK 50 Connector may only be
terminated to the end of two cables. It may not
be daisy-chained.
2. Place the cable stops into the holes in the locator
plate.
3. Using a piece of cable, adjust the cable guide so
that the cable will be positioned in the center of
the locator plate when the edge of the cable is
against the guide. The small ridges on the surface
of the locator plate will help to hold the cable
straight and in position for termination.
4. The locator plate can now be positioned on the
press base under the platen. Some operators
prefer to place the locator plate into the press
after they have prepped the cable and connector
for termination. If you prefer this method, be
sure that the cable and connector do not move
when you place the locator plate into place on the
press.
Base Cover
Cable Stop
Cable guide
Cable Placement
Locator Plate Setup
78-8133-3511-0-A
2
Connector Assembly
Note: For clarity, the pictures show the cable and
connector being positioned on the locator plate
while it is on the table top. This can also be done
while the plate is in position on the press.
The 3M
™
PAK 50 Connector is made to be
terminated to two pieces of 3M
™
3365 Cable. This
is somewhat unusual for an insulation displacement
style connector. The connector has two rows of
contacts. One row of contacts protrudes further from
the connector body than the other. Each row will
terminate one of the two pieces of cable. One piece
of cable will end up against the connector body.
Cover 2 will end up between the two pieces of cable.
The second piece of cable will be on top of Cover 2.
Cover 1 will latch to the body and be on top of the
second piece of cable.
1. Place Cover 1 into the slot on the locator plate.
2. Place the first piece of cable against the cable
guide, between the plastic latches on Cover 1,
and with its end against the cable stops. When
the cable is pressed against the ridges on the
surface of the locator plate, it will become square
to the cover groove and the cover should slide
into position aligned with the cable. Make sure
that the cable is in the grooves on Cover 1.
3. Maintain pressure on the cable with your hand to
keep the cable in position.
Cable guide
Cable Placement
Base Cover
PAK 50E Connector
PAK 50E
Cover 2
Cover 1
Cable Stop
Connector Assembly Steps 1, 2, 3
4. Cover 2 has a cable stop rib on one edge. Place
Cover 2 on top of the cable and between the
latches of Cover 1. The cable stop ridge should
be on the edge of Cover 2 that is in the center of
Cover 1.
No. 2 Cover
Connector Assembly Step 4
3
78-8133-3511-0-A
5. Place the second piece of cable between the
latches of Cover 1, into the ridges of Cover 2
with its end against the cable stop ridge of Cover
2.
6. Maintain pressure on the cables with your hand to
keep the cables in position.
Hand pressure
Place cable up
against no. 2
cover
top cable is
offset_pitch
bottom cable
aligned
Connector Assembly Steps 5, 6
7. Make sure that the tips of the ejector latch on the
connector are pushed in toward the center of the
connector.
8. Place the connector body on top of the cable
engaging the protruding cover latches with the
appropriate slots on the connector body. The
connector may be pressed down by hand for an
initial placement.
Apply the
Connector
Push in
Latch Tips
Hand Pressure
Connector Assembly Steps 7, 8
9. If you did the assembly on the table top, place the
locator plate and cables and connector together
onto the base of the assembly press. Take care
that the cables do not move and that the
connector does not slip out of the groove on the
locator plate.
10. To complete the assembly, push the assembly
press handle down until the press handle stops
against the press frame. This will press the
connector onto the cable permanently.
11. Lift the press handle and remove the terminated
connector and cables from the locator plate.
12. Inspect the finished assembly to assure that the
cover latches are latched fully. If the cover
latches are not completely latched, a minor shut
height adjustment may be required.
Caution: Do not over terminate!
78-8133-3511-0-A
4
Press
handle
down
3442-126
Platen
Connector Assembly Steps 9, 10, 11, 12
3M is a trademark of 3M.
IMPORTANT NOTICE
Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for one year from the date of
purchase.
3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
If this product is defective within the warranty period stated above, your
exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product.
Except where prohibited
by law, 3M will not be liable for any loss or damage arising from this 3M product, whether direct, indirect, special, incidental or consequential
I have read several books introducing 51c language. "51 Single Chip Microcomputer and Its C Language Program Development Examples Edited by Dai Xianjin" is one of the better ones. It introduces more p...
Software tool preparation: 1. Jlink burning software (Setup_JLinkARM_V410i.exe)
2. TFTP software installation under Windows (tftp32.exe)
3. Remote login software (securecrt or Putty)
4. USB to serial ...
How do you calculate the size of a microstrip line if you only know the characteristic impedance? I have consulted relevant literature and found that you need to know at least the characteristic imped...
I just graduated, and the company gave me a task as a probation assessment. I just came into contact with the vxWorks system. Now there is a task that requires me to use the PC serial port to communic...
On August 24th, Jin Yuzhi, CEO of Huawei's Intelligent Automotive Solutions BU, announced the first automotive application of Huawei Qiankun's unique Limera technology. This technology eliminates t...[Details]
Current Development Status of DVR Market
A DVR, or digital video recorder, uses a hard disk for recording, unlike traditional analog video recorders. It's often called a DVR because it's a com...[Details]
Based on a survey of more than ten intelligent robot companies, this article sorts out and analyzes the current development status of the intelligent industry and the challenges and differences it ...[Details]
With the increasing number of new energy vehicles on the road, the deployment of supporting facilities for these vehicles has accelerated, and new energy vehicles have gradually entered the vision ...[Details]
Learned the following information.
Customer product: industrial computer motherboard
Glue application area: CPU/BGA filling
Glue color requirements: black or t...[Details]
The range of an electric vehicle is crucial to the driving experience, and range anxiety is a common headache when driving an electric vehicle. Although the latest electric vehicles can achieve a r...[Details]
Summer is the peak season for buying and using air conditioners. Do you pay attention to the energy efficiency of your air conditioner? Did you buy a DC inverter air conditioner? Do you know the re...[Details]
Wearable technology is taking off, with applications evolving rapidly, from smartwatches to fitness trackers and even smart wigs! Bluetooth Smart is at the center of this revolution. This is the se...[Details]
Most cameras on the market use chips manufactured by Japanese companies like Sony, Sharp, Panasonic, and LG. South Korea now has the capability to produce chips, but the quality is somewhat inferio...[Details]
0 Introduction
With a rapidly aging population, a young couple is now required to care for an increasing number of elderly people, leading to a growing difficulty in providing care for them. E...[Details]
The Radxa Cubie A7A is a single-board computer (SBC) powered by the Allwinner A733 octa-core Cortex-A76/A55 SoC, equipped with a 3 TOPS AI accelerator and up to 16GB of LPDDR5 memory.
Fo...[Details]
With the development of vehicle technology, there are more types of cars. Cars are divided into hybrid, pure electric vehicles, and fuel vehicles. For hybrid cars, they are divided into plug-in hyb...[Details]
As a core component of electric vehicles, power batteries, like batteries for other electronic products, inevitably experience degradation after a certain period of use due to their characteristics...[Details]
We know that the power output by the engine does not directly act on the wheels to drive the car, but needs to pass through a series of power transmission mechanisms. So how is the power transmitte...[Details]
As my country's industrialization continues to improve, environmental pollution is also facing tremendous pressure. In recent years, national environmental protection policies have become increasin...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
