are exceeded. This is a stress rating only and functional operation is not
implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to
“Absolute Maximum Ratings”
conditions for
extended periods may affect device reliability.
2. The data sheet limits are not guaranteed if the device is operated beyond the operating ratings.
3. Due to the limited drive capability, use for input of the same package only.
4. Package thermal resistance assumes exposed pad is soldered (or equivalent) to the device’s most negative potential (GND) on the PCB.
ψ
JB
uses
4-layer
θ
JA
in still-air measurment, unless otherwise stated.
5. The circuit is designed to meet the DC specifications shown in the above table after thermal equilibrium has been established.
6. Includes current through internal 50Ω pull-ups.
7. V
IH
(min) not lower than 1.2V.
M9999-082807
hbwhelp@micrel.com or (408) 955-1690
3
Micrel, Inc.
Precision Edge
®
SY58017U
CML OUTPUT DC ELECTRICAL CHARACTERISTICS
(8)
V
CC
= 2.5V
±5%
or 3.3V
±10%;
T
A
= –40°C to 85°C; R
L
= 100Ω across each output pair, or equivalent, unless otherwise stated.
Symbol
V
OH
V
OUT
V
DIFF_OUT
R
OUT
Parameter
Output HIGH Voltage
Output Voltage Swing
Differential Output Voltage Swing
Output Source Impedance
See Figure 1a
See Figure 1b
Condition
Min
V
CC
–0.020
325
650
40
400
800
50
60
Typ
Max
V
CC
Units
V
mV
mV
Ω
LVTTL/CMOS DC ELECTRICAL CHARACTERISTICS
(8)
V
CC
= 2.5V
±5%
or 3.3V
±10%;
T
A
= -40°C to 85°C, unless otherwise stated.
Symbol
V
IH
V
IL
I
IH
I
IL
Note:
8. The circuit is designed to meet the DC specifications shown in the above table after thermal equilibrium has been established.
Parameter
Input HIGH Voltage
Input LOW Voltage
Input HIGH Current
Input LOW Current
Condition
Min
2.0
Typ
Max
Units
V
0.8
40
–300
V
µA
µA
M9999-082807
hbwhelp@micrel.com or (408) 955-1690
4
Micrel, Inc.
Precision Edge
®
SY58017U
AC ELECTRICAL CHARACTERISTICS
(9)
V
CC
= 2.5V
±5%
or 3.3V
±10%;
T
A
= –40°C to 85°C, R
L
= 100Ω across each output pair, or equivalent, unless otherwise stated.
Symbol
f
MAX
t
pd
t
pd
Tempco
t
SKEW
t
JITTER
Data
Clock
Parameter
Maximum Operating Frequency
V
OUT
≥
200mV
Differential Propagation Delay
Condition
NRZ Data
Clock
IN-to-Q
SEL-to-Q
Differential Propagation Delay
Temperature Coefficient
Input-to-Input Skew
Part-to-Part Skew
Random Jitter
Deterministic Jitter
Cycle-to-Cycle Jitter
Total Jitter
Crosstalk-Induced Jitter
Note 16
t
r
, t
f
Notes:
9. High-frequency AC parameters are guaranteed by design and characterization.
10. Input-to-input skew is the difference in time from and input-to-output in comparison to any other input-to-output. In addition, the input-input skew does
not include the output skew.
11. Part-to-part skew is defined for two parts with identical power supply voltages at the same temperature and with no skew of the edges at the
respective inputs.
12. RJ is measured with a K28.7 comma detect character pattern, measured at 2.5Gbps/3.2Gbps.
13. DJ is measured at 2.5Gbps/3.2Gbps, with both K28.5 and 2
23
–1 PRBS pattern.
14. Cycle-to-cycle jitter definition: the variation of periods between adjacent cycles, T
n
–T
n–1
where T is the time between rising edges of the output
signal.
15. Total jitter definition: with an ideal clock input of frequency
≤
f
MAX
, no more than one output edge in 10
12
output edges will deviate by more than the
specified peak-to-peak jitter value.
16. Crosstalk is measured at the output while applying two similar frequencies that are asynchronous with respect to each other at the inputs.
[size=4]C++Test is based on DSP CCS testing, which uses C++Test together with CCS without special integration. C++Test is not actually integrated with the CCS development environment, but is pre-confi...
[size=2]Here are some misunderstandings and precautions for beginners learning C51. Special applications for experts are not included. [/size] 1) C is taboo to absolute positioning. It is often seen t...
I made a temperature control system using DS18B20 and relays. I initially set the data port of 18B20 to P1.0, but I made a mistake when soldering the board, so I changed it to P1.1. However, it doesn'...
After the partial solar eclipse last year, an annular solar eclipse is coming again. Unfortunately, I am not in the annular eclipse zone, so I can only see a partial solar eclipse.Filmed by CCTV, borr...
[i=s]This post was last edited by fish001 on 2018-1-17 22:12[/i] [p=28, null, left][color=rgb(63, 63, 63)][size=3][b]The definition and generation method of SPWM wave will not be explained here. This ...
Emergency hand-held lamps powered by 6V maintenance-free batteries are widely used in rural areas. The charger used is a transformer step-down and single diode half-wave rectifier, and the charging...[Details]
The rapid development of the Internet has realized high-speed information transmission and resource sharing, greatly facilitating people's lives. Embedded systems are widely used in various electr...[Details]
introduction
Solar cells and LED lighting are typical applications of new energy and energy-saving and efficient technologies. Solar LED lighting uses solar cells to convert solar energy...[Details]
I. Introduction
In the field of power conversion, isolated converters (forward, flyback, and double-ended) with low output DC voltage all use MOSFET as the rectifier device. Since these devi...[Details]
1. Introduction to CIF Board
Fieldbus integration based on PC system
Whether it is a master or a slave, fieldbus has won unanimous praise in the field of PC-based automation. For more...[Details]
Experimental tasks
A DS18B20 is used to form a temperature measurement system. The temperature measurement accuracy reaches 0.1 degrees. The temperature range is between -20 degrees and +50 de...[Details]
In 2012, more than half of the cars in the European, Japanese and American car markets will be equipped with color displays, navigation systems, satellite communications and other in-vehicle infota...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guangzho...[Details]
Liquid crystal display (LCD) panels have a wide range of applications, from small portable electronic devices to large fixed devices, including digital cameras, laptops, personal data assistants, d...[Details]
introduction
At present, measuring instruments are developing towards networking, and each individual embedded instrument will become a node on the Internet. This system realizes the network...[Details]
When the so-called "copycat phones" that flood the domestic mobile phone market move towards large screens, stereo amplifiers, touch controls, and even GPS navigation and mobile TV, the homogeneity...[Details]
Portable power applications are broad and varied. Products range from wireless sensor nodes with average power consumption of only a few microwatts to in-vehicle medical or data acquisition systems...[Details]
1 Battery technology determines the fate of energy vehicles
Regardless of whether new energy vehicles are hybrid or pure electric vehicles, they cannot do without the core technology of batter...[Details]
1 Introduction
Power supply ripple will interfere with the normal operation of electronic equipment, causing malfunctions such as computer crashes, data processing errors and control system fa...[Details]
Current
measurement:
Magnetic balance Hall current
sensor
is used
. The sensor can measure AC from DC to 100kHz.
In automatic measurement and control systems, it is often nec...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
