BU-64703G4-490 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > The embedded processor and controller> Microcontrollers and processors> BU-64703G4-490

BU-64703G4-490: DescriptionMil-Std-1553 Controller, CMOS, CQFP80; CategoryThe embedded processor and controller Microcontrollers and processors; File Size1MB，50 Pages; ManufacturerData Device Corporation

Download Datasheet Parametric View All

BU-64703G4-490 Overview

Mil-Std-1553 Controller, CMOS, CQFP80

BU-64703G4-490 Parametric

Parameter Name	Attribute value
Maker	Data Device Corporation
package instruction	QFP, QFP80,1.1SQ,40
Reach Compliance Code	compliant
JESD-30 code	S-XQFP-G80
Number of terminals	80
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package body material	CERAMIC
encapsulated code	QFP
Encapsulate equivalent code	QFP80,1.1SQ,40
Package shape	SQUARE
Package form	FLATPACK
power supply	3.3,5 V
Certification status	Not Qualified
surface mount	YES
technology	CMOS
Temperature level	MILITARY
Terminal form	GULL WING
Terminal pitch	1 mm
Terminal location	QUAD
uPs/uCs/peripheral integrated circuit type	SERIAL IO/COMMUNICATION CONTROLLER, MIL-STD-1553
Base Number Matches	1

Preview

Download Datasheet

View All

BU-64703

Make sure the next

Card you purchase

has...

SIMPLE SYSTEM RT MARK3

(SSRT MARK3)

FEATURES

•

Complete Integrated Remote Terminal

Including:

•Dual Low-Power 3.3V or 5.0V

Transceivers

•Complete RT Protocol Logic

•

Supports MIL-STD-1553A/B Notice 2,

STANAG-3838 RT, and

MIL-STD-1760 Stores Management

•

World’s Smallest CQFP SSRT

•

80-Pin Ceramic Flat Pack or Gull Wing

Package

DESCRIPTION

The BU-64703 Simple System RT Mark3 (SSRT Mark3) MIL-

STD-1553 terminal provides a complete interface between a simple

system and a MIL-STD-1553 bus. The SSRT Mark3 can be powered

entirely by 3.3 volts, thus eliminating the need for a 5V power supply.

This terminal integrates dual transceiver, protocol logic, and a FIFO

memory for received messages in an extremely small, 0.88 inch

square 0.130” max height ceramic package. The gull wing package

with a “toe-to-toe” maximum dimension of 1.110 inches enables its

use in applications where PC board space is at a premium. The

SSRT Mark3 provides multi-protocol support of MIL-STD-1553A/B,

MIL-STD-1760, McAir, and STANAG-3838.

The SSRT Mark3's transceivers are completely monolithic, require

only a +3.3V supply (+5.0V available), and consume low power. The

internal architecture is identical to that of the original BU-61703/61705

Simple System RT (SSRT). There are versions of the Simple System

RT Mark3 available with transceivers trimmed for MIL-STD-1760

compliance, or compatible to McAir standards. The SSRT Mark3 can

operate with a choice of clock frequencies at 10, 12, 16, or 20 MHz.

The SSRT Mark3 incorporates a Built-In-Test (BIT). This BIT, which is

processed following power turn-on or after receipt of an Initiate Self-

Test Mode command, provides a comprehensive test of the SSRT

Mark3's encoders, decoders, protocol, transmitter watchdog timer,

and protocol section. The SSRT Mark3 also includes an auto-config-

uration feature.

The SSRT Mark3 is ideal for stores and other simple systems that do

not require a microprocessor. To streamline the interface to simple

systems, the SSRT Mark3 includes an internal 32-word FIFO for

received data words. This serves to ensure that only complete, con-

sistent blocks of validated data words are transferred to a system.

•

3.3V Logic Power

•

Meets 1553A/McAir Response Time

Requirements

•

Internal FIFO for Burst Mode Capability on

Receive Data

•

16-bit DMA Interface

•

Auto Configuration Capability

•

Comprehensive Built-In Self-Test

•

Direct Interface to Simple (Processorless)

Systems

•

Available with Full Military Temperature

Range and Screening

•

Selectable Input Clock:

10, 12, 16, or 20 MHz

FOR MORE INFORMATION CONTACT:

Technical Support:

1-800-DDC-5757 ext. 7771

Data Device Corporation

105 Wilbur Place

Bohemia, New York 11716

631-567-5600 Fax: 631-567-7358

www.ddc-web.com

2003 Data Device Corporation

Recommended Resources

Differential bridge amplifier circuit diagram

Low voltage lamp timing flashing circuit using programmable thyristor

Electromechanical control one-way starting full-wave rectification energy consumption braking control circuit

Pressure measurement circuit

555 single power supply converted into positive and negative voltage regulator circuit

Optical fiber controlled bidirectional thyristor AC switch circuit

O-RAN development trends, reference architecture, and interoperability testing: The "open" trend in the field of mobile communications is becoming more and more obvious. O-RAN is definitely one of the hottest terms in the mobile communications industry in the past two years. The ...; ohahaha RF/Wirelessly

Qorvo PAC series highly integrated motor control chips and applications: Qorvo PAC chip is a highly integrated product for three-phase motor control. It can reduce the size and cost of PCB while improving system reliability and shortening system development time. It is wid...; Jacktang RF/Wirelessly

Discussion: How to configure CMD files: I would like to ask you how to configure the CMD file according to the memory status of the film, and how to modify the configuration in the CMD file according to the information in the GEL file and t...; xbj0627 Analogue and Mixed Signal

When will the comprehensive evaluation results be released?: [i=s]This post was last edited by paulhyde on 2014-9-15 03:06[/i] We have two waveforms out of four. I don't know what level this is. It feels rubbish and not very good. It works well on the breadboar...; 风的呼唤 Electronics Design Contest

Land consolidation software GLand: GLand aims at the technical difficulty of earthwork calculation in the current land consolidation planning and design work, and adopts advanced calculation models suitable for various complex terrain ...; homeland Embedded System

When debugging ADX, it jumps to a lot of DCI instructions. The settings of ADS are according to the chip manual, which should be correct. Can you please help me?: When debugging ADX, it jumps to a lot of DCI instructions. The ADS settings are according to the chip manual, which should be correct. Please help me....; aweyfan Embedded System

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components