EEWORLDEEWORLDEEWORLD

Part Number

Search

6DPD-914A959A-10

Description
Antenna Support Circuit, 800MHz Min, 1500MHz Max
CategoryWireless rf/communication    Radio frequency and microwave   
File Size148KB,1 Pages
ManufacturerTOKO, INC.
Websitehttps://www.murata.com/
Download Datasheet Parametric View All

6DPD-914A959A-10 Overview

Antenna Support Circuit, 800MHz Min, 1500MHz Max

6DPD-914A959A-10 Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
MakerTOKO, INC.
Reach Compliance Codeunknown
bandwidth1 MHz
Characteristic impedance50 Ω
OmnidirectionalNO
Maximum operating frequency1500 MHz
Minimum operating frequency800 MHz
Maximum operating temperature85 °C
Minimum operating temperature-25 °C
polarizationLINEAR
RF/Microwave Device TypesANTENNA SUPPORT CIRCUIT
Maximum transmission power1 W
Maximum voltage standing wave ratio2
Base Number Matches1
【X-Nucleo experience】Received X-NUCLEO-IDB04A1 and installed MDK
[i=s] This post was last edited by ddllxxrr on 2014-11-23 10:22 [/i] I received the X-NUCLEO-IDB04A1, here are the photos: The packaging when it arrived:The back, it is still made in ItalyThe front:Si...
ddllxxrr stm32/stm8
ZW310-Marvell PXA310 Development Solution
Introduction to Marvell PXA310 Teaching Experiment Platform --- ZW310 Development Platform [img]http://www.zhanweitech.com/attachment.aspx?attachmentid=19[/img] Introduction to Marvell PXA310 Teaching...
junuo Embedded System
Has anyone used AD5724R or AD57xx series chips? . . .
Has anyone used AD5724R or AD57xx series chips? . . . How to control it specifically? I looked at the chip data and no matter how I operate it, it is wrong. . First write the output range register, th...
hj1013 MCU
Which model is better for motor control, DSP or arm?
Which model is better for motor control, DSP or arm?...
安_然 DSP and ARM Processors
Level conversion circuit
How should I interpret the circuit here? The gate and drain are shorted together. Since the I/O port of the microcontroller can only withstand 0 to 5 V, the output signal needs to be pulled to12 V so ...
~胖球 Analogue and Mixed Signal
How to set the IP of the board!
I only have an Internet cable, a router, and a computer. No serial port, no SD card (I don't want to spend money to buy one). How to set the IP of the board? First, you need to know the IP of the boar...
klyz12ss DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1800  47  1262  2465  2539  37  1  26  50  52 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号