– 100MHz, 133MHz, 150 MHz, 180MHz, 200MHz and 267MHz
operation frequencies
x
High-performance DSP capability
– 133.5 Million Integer Multiply-Accumulate Operations/sec @
267 MHz
x
High-performance microprocessor
– 133.5 M Mul-Add/second at 267MHz
– 89 MFL0P/s at 250MHz
– >640,000 dhrystone (2.1)/sec capability at 267MHz
(352 dhrystone MIPS)
x
High level of integration
– 64-bit, 267 MHz integer CPU
– 8KB instruction cache; 8KB data cache
– Integer multiply unit with 133.5M Mul-Add/sec
x
Low-power operation
– Active power management powers-down inactive units
– Standby mode
x
Upwardly software compatible with IDT RISController
Family
Large, efficient on-chip caches
– Separate 8kB Instruction and 8kB Data caches
– Over 3200MB/sec bandwidth from internal caches
– 2-set associative
– Write-back and write-through support
– Cache locking to facilitate deterministic response
x
Bus compatible with RC4000 family
– System interface provides bandwidth up to 1000 MB/S
– Direct interface to 32-bit wide or 64-bit wide systems
– Synchronized to external reference clock for multi-master
operation
– Socket compatible with IDT RC64475 and RC64575
x
Improved real-time support
– Fast interrupt decode
Optional cache locking
x
Note:“R” refers to 5V parts; “RV” refers to 3.3V parts; “RC”
refers to both
352 M IP S 64-bit C P U
64-bit register file
System C on trol C oprocessor
A d dress Tran slation/
C ache A ttribu te C ontrol
89M F L O P S Sin gle-P recision F PA
FP register file
P ip elin e C o n tro l
L oad aligner
S tore A ligner
Logic U nit
H igh-Perform an ce
In teger M u ltiply
Exception M an agem en t
F u nctions
P ip e lin e C o n tro l
64-b it ad der
P ack /U n pack
F P A dd /S ub /C vt/
D iv/S qrt
FP M ultiply
C ontrol B us
D ata Bu s
Instru ction Bu s
Instru ction C ach e
S et A
(Lock able)
In stru ctio n C a che
Set B
3 2 -/6 4 -b it
S y n c h ro n ize d
S y ste m In ter fa ce
D ata C ach e
S et A
(Lockable)
Data Cache
Set B
The IDT logo is a registered trademark and ORION, RC4600, RC4650, RV4650, RC4700, RC3081, RC3052, RC3051, RC3041, RISController, and RISCore are trademarks of Integrated Device Technology, Inc.
When you touch the surface of the power module, it feels hot. Is the module broken? Wait a minute, it is a little hot just because it is working hard. But high temperature has a great impact on the re...
DPS (Digital Pixel System) is a breakthrough technology in the field of imaging and image processing. Its revolutionary image capture and processing method allows the dynamic range of the camera to be...
A servo motor has no other performance issues, but it cannot reach the rated speed when running. The motor nameplate says 3000RPM, but the actual driver can only drive the motor to a maximum no-load s...
In recent years, there are more and more LED packaging manufacturers, production technology is becoming more mature, and the application field is becoming more extensive and popular. However, many LED...
The picture shows two header files in the example program in the development board of TMS320LF2407. This way of defining registers is different from the way defined in 2812. I don’t understand why it ...
With the rapid development of science and technology, especially the widespread application of digital technology and various ultra-large-scale integrated circuits, electronic equipment, especially...[Details]
In recent years, lighting has become an important area that countries around the world are targeting to promote energy conservation and environmental protection. According to statistics, about 20% ...[Details]
Aromatic gases are widely present in food, medicine, cosmetics and various daily chemical products, such as snacks, liquor, spices, Chinese herbal medicines, plasters, perfumes, soaps, shampoos, et...[Details]
introduction
MAX6636 is a multi-channel precision temperature monitor that can not only monitor local temperature, but also connect up to 6 diodes externally. Each channel has a programmable...[Details]
Abstract: Aiming at the needs of coal-rock acoustic emission signal monitoring system, a data acquisition circuit with 24-bit resolution and 16-channel synchronous data acquisition function is desi...[Details]
Abstract: The output of high-range acceleration sensor is less than 10 mV under the excitation of small signal. The noise of traditional test system may cover such small voltage signal, so that hig...[Details]
Temperature compensated quartz crystal oscillator (TCXO) is widely used as a high-precision frequency source in communication systems, radar navigation systems, precision measurement and control sy...[Details]
1 Development of LED Film and Television Lighting
1.1 The significance of developing film and television lighting
Lighting power consumption accounts for a large proportion of the total p...[Details]
Mobile phones, MP3s, tablet computers, laptops, digital cameras, handheld game consoles, navigation devices, etc., all these mobile devices are powered by mobile batteries, and the battery life is ...[Details]
The power supply is the core component of a computer. Although it is not of high value, all computer components rely on the switching power adapter to provide energy, so the stability of a power su...[Details]
Measurement compatibility
It is very important to ensure the compatibility between the pressure sensor and its actual application. Before making a pressure sensor selection, the fo...[Details]
introduction
The core features of mobile value-added service products are mobility, immediacy and personalization. Mobile value-added services are a new service mode that is rapidly developing...[Details]
1 Introduction
Fieldbus is a serial, digital, multi-point communication data bus between field equipment/instruments installed in the production process area and automatic control devices/syst...[Details]
UDN2916LB is a two-phase stepper motor bipolar driver integrated circuit launched by SANKEN. It can drive dual-winding bipolar stepper motors and is particularly suitable for controlling dual-step ...[Details]
Stepper motors have been widely used in automatic or semi-automatic equipment such as CNC machine tools, medical equipment, and instruments. The usual way to control stepper motors with computers i...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
