805-007BPHAAMPN-72 datasheet, PDF

Datasheet> All Categories > The connector> The connector> 805-007BPHAAMPN-72

805-007BPHAAMPN-72: DescriptionInterconnection Device; CategoryThe connector The connector; File Size445KB，8 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/

Download Datasheet Parametric View All

805-007BPHAAMPN-72 Overview

Interconnection Device

805-007BPHAAMPN-72 Parametric

Parameter Name	Attribute value
Maker	Glenair
Reach Compliance Code	compliant
Connector type	INTERCONNECTION DEVICE
Base Number Matches	1

Preview

Download Datasheet

View All

Series 80 “Mighty Mouse”

ASAP Cordsets For Ethernet, IEEE 1394 and USB 2.0

ASAP Cordsets For High Speed Serial Data

Upgrade commercial high speed serial interconnects

mil spec performance. Glenair’s ASAP “Mighty Mouse”

cordsets are available for 100BASE-T, Gigabit Ethernet,

IEE 1394 and USB 2.0 applications.

These cordsets combine aerospace-grade data cables

with Series 80 “Mighty Mouse” harsh environment

connectors for maximum performance and minimum

size.

FEP jackets

meet FAA flammability requirements. Or,

choose

low smoke/ zero halogen polyurethane jackets

for mass transit or shipboard applications.

100BASE-T Cordset With 4 Pin Series 800

Connector

Three Strain Relief Options

– Overmolded, threaded

backshell or heatshrink boots.

HOW TO ORDER CORDSETS

Step 1: Select the Connector Series

Table1 lists the six types of Series 80 connectors. For more information on selecting

a connector, please refer to the connector selection chart in the Introduction.

Step 2: Select the Cable

Table 2 contains speciﬁcations for standard data cables. The cable type also

determines the connector layout.

4 pin connectors are used for 4 wire cables,

and tem pin connectors are used for 8 wire cocables.

Step 3: Select a Cable Jacket

Table 3 shows available jacket options. Choose FEP ﬂourocarbon jackets

for airframe and avionics applications, or choose low smoke/zero halogen

polyurethane jackets for soldier systems, vehicles, and transit systems.

Step 4: Select a Cable-To-Connector Interface

Table 3 provides three ways to attach the cable to the connector:

1. Polyamide boot, overmolded with ﬂexible strain relief

2. Aluminum backshell, shielded, watertight a nd removable

3. Heat-shrink boot, low smoke/ zero halogen

Step 5: Select a Connector Conﬁguration

Table 1 shows connector codes for specifying plug versus receptacle and pin

versus socket contacts. Add a plating code, keying option and length.

CAGE Code 06324/0CA77

Printed in U.S.A.

GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912

www.glenair.com

J-1

E-Mail: sales@glenair.com

Recommended Resources

Typical recording equalization amplifier circuit

Discrete component sound and light control stair delay switch circuit (5)

SH-816 Holiday Lights ASIC

HT-1601/HT-1602 circuit

Fluorescent lamp circuit with reactive power compensation

Full duplex telephone system circuit diagram

The capture card driver I wrote myself has a blue screen every once in a while. I use windbg to open the dmp file, but I can't understand the analysis content. Can you help me take a look? Thanks in advance: Microsoft (R) Windows Debugger Version 6.11.0001.404 X86 Copyright (c) Microsoft Corporation. All rights reserved.Loading Dump File [C:\WINNT\Minidump\Mini073009-02.dmp] Mini Kernel Dump File: Only re...; davidlee2046 Embedded System

RLC meter based on lm3s: Attached are some pictures of itThe program and schematic diagram of the measuring device are as follows[[i]This post was last edited by Panda on 2011-3-7 14:02[/i]]...; 熊猫 Microcontroller MCU

The world's smallest EDA tool: Ruby 2.0 is the world's smallest domestic EDA simulation tool (less than 5M), with a very modern interface, very simple operation mode and the integration of visualization and code design. Simplifying...; micbot FPGA/CPLD

Why does LM3S9B92 enter FaultISR when using STR instruction?: I was studying uCOS-III recently, and found a problem after porting it. When debugging, the program always enters the infinite loop of FaultISR. But if I power on and run it directly, the program can ...; ultrabenz Microcontroller MCU

Help with a quartus schematic problem: I want to use QuartusII9.0 to draw schematics, but after I open it according to the steps, it keeps reminding me to install a printer. I can't draw the schematics. I want to find a solution. I uninsta...; 阿飞 FPGA/CPLD

AVR LED Blinking Program Why does the LED stay on and not blink? Software: ICCAVR Progisp: [color=rgb(0,0,0)]#include [/color] [color=rgb(0,0,0)]#include [/color] [color=rgb(0,0,0)]void delay(void) [/color] [color=rgb(0,0,0)]{ [/color] [color=rgb(0,0,0)]unsigned char a,b; [/color] [color=rg...; cc2513685 Microchip MCU

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components