EEWORLDEEWORLDEEWORLD

Part Number

Search

50F0006

Description
Power/Signal Relay, DPDT, Latched, 0.12A (Coil), 6VDC (Coil), 720mW (Coil), 2A (Contact), 28VDC (Contact), DC Input, AC/DC Output, Panel Mount,
CategoryMechanical and electronic products    relay   
File Size1MB,9 Pages
ManufacturerEsterline Technologies Corporation
Download Datasheet Parametric View All

50F0006 Overview

Power/Signal Relay, DPDT, Latched, 0.12A (Coil), 6VDC (Coil), 720mW (Coil), 2A (Contact), 28VDC (Contact), DC Input, AC/DC Output, Panel Mount,

50F0006 Parametric

Parameter NameAttribute value
MakerEsterline Technologies Corporation
Reach Compliance Codeunknown
ECCN codeEAR99
body width10.2 mm
body height10.4 mm
Body length or diameter20.4 mm
Maximum coil current (DC)0.12 A
Coil operating voltage (DC)4.6 V
Coil power720 mW
Coil release voltage (DC)4.6 V
Coil resistance50 Ω
Maximum coil voltage (DC)6 V
Coil/Input Power TypeDC
Contact (AC) maximum rated R load.3A@115VAC
Maximum contact current (AC)0.3 A
Maximum contact current (DC)2 A
Contact (DC) maximum rated R load2A@28VDC
Maximum contact voltage (AC)115 V
Maximum contact voltage (DC)28 V
Contact/Output Power TypeAC/DC
Electrical life100000 Cycle(s)
Installation featuresPANEL MOUNT
operating hours4 ms
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
physical size20.4mm x 10.2mm x 10.4mm
GuidelineSCC
Relay actionLATCHED
Relay functionDPDT
Relay typePOWER/SIGNAL RELAY
release time6 ms
sealCORROSION PROOF; HERMETICALLY SEALED
surface mountNO
Termination typeSOLDER HOOK
Base Number Matches1
GP2/GP2A
ENGINEERING DATA SHEET
RELAY - LATCH
2 PDT, 2 AMP
Polarized, latching hermetically sealed relay
2 PDT
Contact arrangement
Coil supply
Qualified to
Direct current
SCC3602/003
PRINCIPLE TECHNICAL CHARACTERISTICS
Contacts rated at
Weight
Dimensions of case
2 Amps / 28 Vdc
11 grams max
20.4mm x 10.4mm x 10.2mm
Hermetically sealed, corrosion protected metal can.
APPLICATION NOTES:
001
007
CONTACT ELECTRICAL CHARACTERISTICS
Minimum
operating cycles
100,000 cycles
100,000 cycles
1,000,000 cycles
100 cycles
Contact rating per
pole and load type
resistive load
inductive load (L/R=5ms)
low level (30µA/30mV)
resistive overload
Load Current in Amps
@28Vdc
2
0.75
-
4
@115Vac/60-400Hz
0.3
-
-
-
Featuring
LEACH
©
power and control solutions
www.esterline.com
AMERICAS
6900 Orangethorpe Ave.
P.O. Box 5032
Buena Park, CA 90622
.
.
Tel: (01) 714-736-7599
Fax: (01) 714-670-1145
EUROPE
2 Rue Goethe
57430 Sarralbe
France
.
.
Tel: (33) 3 87 97 31 01
Fax: (33) 3 87 97 96 86
ASIA
Units 602-603 6/F Lakeside 1
No.8 Science Park West Avenue
Phase Two, Hong Kong Science Park
Pak Shek Kok, Tai Po, N.T.
Hong Kong
Tel: (852) 2 191 3830
Fax: (852) 2 389 5803
Data sheets are for initial product selection and comparison. Contact Esterline Power Systems prior to choosing a component.
Date of issue: 10/10
- 17 -
Page 1 of 4
Big question about PCB
What is the reason for the silver-yellow circle around the pad as shown in the above picture? DRC check passed! Urgent:)...
phdwong PCB Design
s3c6410 - DVFS (Dynamic Voltage Frequency Scaling) function
Has anyone worked on the DVFS (Dynamic Voltage Frequency Scaling) function of s3c6410? In Samsung's documents, there is little introduction to DVFS. It seems that you can use some functions by setting...
lingilngmj Embedded System
[Low Power] Lattice is determined to develop low-power and low-cost FPGAs
Lattice is determined to develop low-power and low-cost FPGAs. Lattice is also a familiar FGPA manufacturer with its own characteristics. I hope more people can recognize it....
cillyfly FPGA/CPLD
Learn simulation + [Reading notes 3 of "Operational Amplifier Noise Optimization Handbook"]
[i=s] This post was last edited by Sur on 2014-5-23 23:46 [/i] What is op amp noise? How to analyze op amp noise? First, determine the goal. You should have a goal when doing anything. Let's talk abou...
Sur Analogue and Mixed Signal
Could you please tell me what circuit is generally used to implement the 0/4-20mA drive circuit?
Could you please tell me what circuit is generally used to implement the 0/4-20mA drive circuit? I have a plan like this, I wonder how competitive it is? For your referenceAttached datasheet...
zjqmyron Motor Drive Control(Motor Control)
Help, how should the Analog Input port be used?
Hey guys, I'm using NS's LM4935 chip, which has two ports, AUX_L and AUX_R. The datasheet describes them as Left Analog Input and Right Analog Input. How should I use them? I want to use them as signa...
felxyy Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2280  1421  1514  1090  1652  46  29  31  22  34 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号