The 3M Locator Plate 3443-106N is designed to aid in
the assembly of the preassembled and two-piece 3M
™
Delta Connector and pin 9 through 37 position
connectors. End-to-end, as well as daisy chain
assemblies, can be made. Set-up and assembly
instructions are based on termination procedures with
the 3M manual and pneumatic presses.
Locator Plate Includes
• Instruction sheet
• One mounting screw
• Mounting studs for cable guides
Note:
For the one-piece preassembled connector,
all locator plate part options are listed on
the last page of the assembly instructions.
Tool Preparation
Shut Height Setting
Connector
3640
3316
82XX
83XX
21
21
Assembly Press
3335
3339-1
21.5
21.5
3830
Self-Adjusting
Adjust the shut height setting before installing the Locator Plate and Platen using the 3M™ Shut
Height Gauge 3436-1.
PIN
D
A
F
B
E
C
Note:
If the staging platform (optional) is used, please refer to that instruction sheet for mounting
instructions.
78-8133-3685-2-A
2
Preassembled Connector Assembly Procedure
Set-up
1. Adjust the end block according to the flange style and connector size.
A
Thru-hole style:
Rotate the end block so that the locating pin is facing the inside of the locator plate.
The pin has to be removed so that the end block can be rotated. Then reassemble the pin. The pin is
used to guide the platen during harness assembly.
B
Floating bushing and threaded insert style:
Rotate the end block so that the locating pin is facing the outside of the locator plate.
2. Install the cable stop insert 3664-B.
C
3. Install the cable guide on the mounting stud. Refer to the last page for the appropriate guide.
D
4. Place the locator plate on the press and affix it using the locking screw provided.
5. Place the platen on the assembly press. Refer to the last page for the appropriate platen.
Assembly
1. Cut required cable length using one of the 3M cutting tools.
2. Remove the connector from the packing strip.
3. Slide the connector onto the guiding groove and into the end block.
E
4. Slide the cable under the cable guide. If the cable should not enter into the connector smoothly, check the
flatness of the cable.
F
5. Complete the assembly by bringing the press handle to the full downward position.
6. Raise the press handle and cable guide, then remove completed assembly.
7
Visually inspect to insure that:
a. The cover is fully seated. If not, check the shut height setting.
b. The cable is correctly aligned in the cover. If not, check end guide adjustment.
Two-Piece Connector Assembly Procedure
Set-up
1. Follow steps 1, 4 and 5 of the preassembled set-up instructions.
Assembly
1. Grasp 3M
™
Delta Cover Strip between thumb and forefinger. While holding the adjacent cover, pull laterally
away from strip leaving the adhesive with a smooth clean edge.
2. Press cable ribs into cover alignment grooves.
3. Visually inspect to insure that the cable is properly aligned and oriented into cover grooves.
4. Engage cable/cover subassembly with connector body. Place subassembly in the locator plate with the
connector body facing up.
5. Complete the assembly by bringing the press handle to the full downward position.
6. Raise the press handle and remove the completed assembly.
7. Visually inspect to insure that:
a. The cover is fully seated. If not, check the shut height setting.
b. The cable is correctly aligned in the cover. If not, check end guide adjustment.
3
78-8133-3685-2-A
Standard Two-Piece Connector
The 3M
™
Locator Plate 3443-106N and the Platen listed below is all that is needed for the assembly of the
standard two-piece connector.
Connector
Number
8209
8309
8215
8315
8225
8325
8237
8337
Locator
Plate
3443-106N
3443-106N
3443-106N
3443-106N
3443-106N
3443-106N
3443-106N
3443-106N
Platen
3442-39N
3442-9
3442-39N
3442-9
3442-41N
3442-9
3442-41N
3442-9
Cable Guide
3664-09
3664-09
3664-15
3664-15
3664-25
3664-25
3664-37
3664-37
Cable Stop
Open Cover
3664-B
3664-B
3664-B
3664-B
3664-B
3664-B
3664-B
3664-B
Cable Stop
Closed Cover
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Note:
Replacement studs are available for the cable guides, part number 3664-C. Optional End Block,
3664-A, for connectors with floating bushings and threaded inserts is also available.
CAUTION
The 82XX series connector must use the 3M™ 3442-39N Platen. The
3442-39N platen has three blade-like protrusions on the surface of the
platen. These blades must fit inside the metal shell of the connector and
the connector pins must fit in the grooves between the blades when the
platen engages the connector. Make sure that there is good alignment
between the connector and the platen to assure that the shell or pins of
the connector are not damaged during termination.
3M is a trademark of 3M.
IMPORTANT NOTICE
Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for one year from the date of
purchase.
3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
If this product is defective within the warranty period stated above, your
exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product.
Except where prohibited
by law, 3M will not be liable for any loss or damage arising from this 3M product, whether direct, indirect, special, incidental or consequential
The code is as follows:#includestdio.h
#includestdlib.h
intmain()
{
while(10)
{
printf("01");
}
system("pause");
return0;
}
The effect is as follows:Friendly reminder: This code is prone to jamming wh...
Today I happened to be testing various small stepper motors with a board, and I happened to test this photoelectric relay by the way. Use a switching power supply to power directly. The switching powe...
I first heard about Cortex-M3 in the last year of 2007. I had just started working and was still learning AVR. I thought AVR was so powerful. Some of my colleagues were already using ARM, and I always...
I have some questions that I need your advice. In the charging circuit, when the charger is inserted, Q3 is turned on and the SW voltage is 0. Then the upper tube Q2 is turned on. The condition for th...
1. Overview
Will passive devices
produce nonlinear intermodulation distortion? The answer is yes! Although there is no systematic theoretical analysis, it has been found in engineerin...[Details]
introduction
In the discharge process of tokamak plasma physics, the study of rupture and sawtooth is of great significance. Rupture and sawtooth exist in most tokamaks. Rupture is a notew...[Details]
1 Introduction
With the acceleration of the pace of urban modernization, society has higher requirements for urban road lighting and urban lighting projects. The state has clearly required tha...[Details]
As LEDs continue to improve in almost every aspect of performance and cost, LED lighting is being used in an increasingly wide range of applications, among which LED street lights are a focus of in...[Details]
We know that microcontroller development tools generally include real-time online emulators and programmers. Among them, online emulators are very good tools, but they are also more expensive...[Details]
This week, Microsoft held its 2012 Microsoft Worldwide Partner Conference (WPC) in Toronto, Canada. At the conference, Microsoft showed its new products and services to partners around the world. A...[Details]
With the rapid development of intelligent control technology, computers and information technology, the trend of information appliances IA (Information Application), computers and communications integ...[Details]
hint:
The number of speakers and their spacing limit the sound field of a portable stereo system.
Spatial audio attempts to artificially recreate the experience of listening to sounds i...[Details]
D5026A is a driver IC designed by Shanghai Debei Electronics for energy-saving LED display screens. Its design concept is energy-saving and compatible with existing solutions, that is, it can be ...[Details]
1 Basic Features
In computer control systems and various intelligent instruments and meters composed of single-chip microcomputers (or microprocessors), various external analog signals must be ...[Details]
Currently, each country is developing its own USB interface
charging specifications
, which leads to a major problem that a USB interface
charging
device manufactured in one country...[Details]
1 Load Regulation
Changes in power supply load will cause changes in power supply output. When the load increases, the output decreases, and vice versa, when the load decreases, the output inc...[Details]
In recent years, with the increasing maturity of LED technology, LED light sources have been increasingly widely used due to their advantages of using low-voltage power supply, low energy consumpti...[Details]
Infrared remote control is widely used in home appliances, but the remote controls produced are not compatible with each other. The universal remote controls commonly seen on the market can only co...[Details]
1. Project Introduction
Beijing Benz-Daimler Chrysler Co., Ltd. is a joint venture between Beijing BAIC Group and Benz-Daimler Chrysler. In October 2005, it started to build a new automobile ...[Details]
PCB Design
京公网安备 11010802033920号
EEWORLD
