DEVICE PARAMETERS, FIXED and ADJUSTABLE REGULATORS
f
O
Oscillator Frequency
50
52
100/
500
nA
kHz
kHz(min)
kHz(max)
V
V(max)
%
%(max)
A
A(min)
A(max)
mA(max)
mA
mA(max)
mA
mA(max)
µA
µA(max)
°C/W
47/
42
58/
63
Saturation Voltage
Max Duty Cycle (ON)
Current Limit
I
OUT
= 1A (
Note 4
)
(
Note 5
)
Peak Current, t
ON
≤
3µs (
Note 4
)
0.9
1.2/
1.4
98
93
2.2
1.7/
1.3
3.0/
3.2
2
75
30
5
10
Standby Quiescent Current
ON/OFF Pin = 5V (OFF)
50
200
65
45
2
85
100
1.4
1.2
4
30
ON /OFF Pin = 0V (ON)
0.01
10
2.2/
2.4
1.0/
0.8
V
SAT
DC
I
CL
I
L
Output Leakage Current
V
IN
= 40V, (
Note 6
),
(
Note 6
)
(
Note 6
)
Output = 0V
Output = –1V
Output = –1V
I
Q
I
STBY
Quiescent Current
T Package, Junction to Ambient (
Note 7
)
θ
JA
Thermal Resistance
T Package, Junction to Ambient (
Note 8
)
θ
JA
θ
JC
T Package, Junction to Case
N Package, Junction to Ambient (
Note 9
)
θ
JA
WM Package, Junction to Ambient (
Note 9
)
θ
JA
ON/OFF CONTROL, FIXED and ADJUSTABLE REGULATORS
Test Circuit Figure 1
V
IH
V
IL
I
IH
I
IL
Notes:
ON/OFF Pin Logic
Input Level
ON/OFF Pin Logic
Current
V
OUT
= 0V
V
OUT
= 5V
ON /OFF Pin = 5V (OFF)
V(min)
V(max)
µA
µA(max)
µA
µA(max)
1. Absolute Maximum Rating indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device
is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical
Characteristics.
2. All limits guaranteed at room temperature (standard type face) and at
temperature extremes (bold type face).
All room temperature limits are100%
production tested. All limits at
temperature extreme
are guaranteed via testing.
3. External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance. When the
LM2575/LM1575 is used as shown in Figure 1 test circuit, system performance will be shown in system parameters section of Electrical
Characteristics.
4. Output (pin 2) sourcing current. No diode, inductor or capacitor connected to output.
5. Feedback (pin 4) removed from output and connected to 0V.
6. Feedback (pin 4) removed from output and connected to 12V to force the output transistor OFF.
7. Junction to ambient thermal resistance (no external heat sink) for the 5-pin TO-220 package mounted vertically, with 1/2" leads in a socket, or on PC
board with minimum copper area.
8. Junction to ambient thermal resistance (no external heat sink) for the 5-pin TO-220 package mounted vertically, with 1/4" leads soldered to PC
board containing approximately 4 square inches of copper area surrounding the leads.
9. Junction to ambient thermal resistance with approximately 1 square inch of pc board copper surrounding the leads. Additional copper will lower
I have been thinking about a question: How is the current carrying capacity of a wire measured? The resistance of wires of the same thickness is the same at any voltage; if the current carrying capaci...
I'm here to ask you all for help. I've had experience with C++ and assembly language development on Windows before, but I studied computer science instead of electronics in college, so I don't have an...
Dear teachers and seniors, my graduation project involves the connection between these two modules. SP12 is a temperature and pressure sensor. My job is to process the data collected by SP12 through 4...
Since the SWD method seems to use two fewer IO ports than the JTAG method for simulation and debugging, I want to keep only the SWD debugging interface for products in the future. After looking at the...
introduction
1 The significance of using RTOS on MSP430
It is understandable that it is meaningless to use RTOS on MSP430. Because the hardware resources of MSP430 are limited (for exampl...[Details]
0. Introduction
In daily life, we often see some special-purpose vehicles. When these vehicles pass through intersections, they often obtain the right of way at intersections by temporarily op...[Details]
No matter which processor you are learning, the first thing you need to understand is the registers and working mode of the processor.
ARM has 37 registers, including 31 general registers and ...[Details]
System design is a complex process. It is not enough to just use ICs. There are many details to consider. This article uses a high-fidelity music playback system as an example to introduce how to s...[Details]
When choosing a laptop battery, you should consider several factors, such as power, appearance, and quality.
Regarding power, we often see that a manufacturer uses values such as the number ...[Details]
1 Introduction
Intelligent control instruments are one of the most commonly used controllers in industrial control. They are mainly aimed at a specific parameter (such as pressure, tempera...[Details]
With the advocacy and implementation of the government's Safe City Plan, the security market has increasingly higher requirements for the clarity of surveillance images. Imagine that after a case o...[Details]
With the widespread application of new services and technologies in the communications industry, the scale and capacity of operators' network construction are getting larger and larger, and the ris...[Details]
In the "digital pressure measurement" experimental device of applied physics, the subject technical knowledge of analog circuits, digital circuits, sensors and single-chip microcomputers is used. In o...[Details]
0 Introduction
In order to improve the automation control of shortwave transmitters, so that they can automatically process from far to near, the technicians here use the ICS system to complete the ...[Details]
People who often surf the Internet until late at night, their families always complain that turning on the big lights in the living room affects their rest, but some people don't have keyboard ligh...[Details]
LED is now known as the fourth generation of light sources. High-power LED has many advantages over traditional light sources in outdoor lighting.
1 LED lamps have high light efficiency
C...[Details]
a. Keep the battery clean, wipe off the spilled electrolyte, contaminated dirt and dust in time; keep the poles and terminal clamps clean and in good contact, and apply vaseline or butter to preven...[Details]
summary
This article will briefly analyze the success and shortcomings of high-frequency DC-DC switching power supplies in the process of miniaturization (the second basic goal), and propose m...[Details]
This article focuses on closing the feedback loop of an isolated power supply using a TL431 shunt regulator. The article discusses a method to extend the bandwidth of the power supply control loop ...[Details]
Industrial Control Electronics
京公网安备 11010802033920号
EEWORLD
