20-pin SOIC-W, 19 Bussed Resistors; 100% tin (Pb-free) terminations
Absolute TCR Code
00 = ±250ppm/°C; 01 = ±100ppm/°C
02 = ±50ppm/°C; 03 = ±25ppm/°C
Resistance Code
4-Digit Resistance Code
Ex: 1002 = 10K , 50R1 = 50.1
(The USA style coding shown is preferred, but, historically, European style coding (e.g. 10K) may have been used.)
Absolute Tolerance Code
J = ±5%; G = ±2%; F = ±1%; D = ±0.5%
C = ±0.25%; B = ±0.1%
Optional Ratio Tolerance Code
G = ±2%; F = ±1%; D = ±0.5%;
C = ±0.25%; B = ±0.1%; A = ±0.05%
Packaging
Specify tubes or tape & reel.
Tape and reel packaging is compliant with EIA-481-D: 8 mm through 200 mm Embossed Carrier Taping and 8 mm and 12 mm Punched Carrier Taping of Surface Mount Components
for Automatic Handling.
Tube packaging drawing detail available upon request.
After writing the program into the MCU, the program does not run (the diode driven by port B does not light up); when I touch the crystal oscillator input pin of the MCU with my hand, the MCU can run....
LED fluorescent lamp power supply is very popular this year. Many companies design products that often have problems in the certification stage due to not understanding the specifications, and spend a...
There is a USB detection. When the USB is detected, the red light in RGB will be displayed. When the key is pressed for the first time, it will light up white. There are five gears corresponding to fi...
When I used the board wizard, I set the following rules to run two lines between two pads. However, after I finished the layout and routed, I found that my board components were a bit dense, and the t...
As the title says, for example, for a two-layer PCB
After copper is applied to both the top GND and the bottom GND
Why do we need to place several vias on the GND copper between the two layers? (After...
For 80,000
ZTE
(000063.SZ) employees and more Chinese ICT (information and communication technology) industry practitioners, the news from across the ocean on the evening of April 16 kept t...[Details]
In the actual project development process, we often need to get the running time of a section of code. The usual method is to use an oscilloscope to measure it. This blog post will use SysTick to acc...[Details]
When the domestic discussion about "ZTE being banned" was hot, Alibaba officially announced the acquisition of chip supplier
Zhongtianwei
, but the investment amount was not disclosed. At t...[Details]
stm32cubeMX graphical configuration content STM32CubeMX is part of the original STMCube initiative from st microelectronics, and STM32Cube includes STM32CubeMX. STM32CubeMX is a graphical software co...[Details]
I used STM32CubeMX V4.22.1 to generate a project including EHT and Lwip. The debugging has been abnormal. After careful inspection, the following problems were found: 1. The hardware uses LAN8720A, b...[Details]
Timing and protocol are two key points in digital system debugging, and they are also where logic analyzers can play their most valuable role. How can we use a logic analyzer to quickly complete wiri...[Details]
Artificial Intelligence (AI) is undoubtedly the hottest topic in the technology industry in the past one or two years. In addition to the huge investments made by technology giants, financial and o...[Details]
Different from 51, AVR and other single-chip microcomputers, the clock signal sources of msp430 include LFXT1, XT2 and DCO. 1. LFXT1: It can connect high-speed and low-speed crystal oscillators. In l...[Details]
At the beginning of the new year of 2018, after the release of the national photovoltaic policy, we found that the state’s support for village-level poverty alleviation power stations has not weake...[Details]
With the large-scale development of the domestic household photovoltaic market and the improvement of component and inverter technology, the system cost has dropped significantly in the past year. The...[Details]
From the functional classification, it can be divided into: 1. Active control ADAS: ACC/AEB/LKS, etc. 2. Warning ADAS: FCW/LDW/PCW, etc. 3. Other auxiliary ADAS: BSD/ADB/panora...[Details]
/* Unfortunately, it cannot generate a standard 38kHz frequency square wave, there is a little error*/ #include reg51.h #define uchar unsigned char #define uint unsigned int sbit Waveout=P1^0; //P...[Details]
;Question: The 80C51 single-chip microcomputer has a fosc = 6MHz. It is required to use the T1 timer working mode 1 to perform a timing of 40ms. And P1.7 periodically outputs a rectangular wave with ...[Details]
As shown in the figure, the circuit is required to count and display the number of times the button is pressed. When the button is pressed once, the count value increases by 1 (it is required to accu...[Details]
LiDAR is a comprehensive light detection and measurement system. Compared with ordinary radar, LiDAR can provide high-resolution radiation intensity geometric images, distance images, and speed im...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
