Freescale Semiconductor
Data Sheet: Technical Data
Document Number MCF51QU128
Rev. 5, 03/2015
Supports the MCF51QU128VLH,
MCF51QU128VHS, MCF51QU64VLF,
MCF51QU64VHS, MCF51QU32VHS,
MCF51QU32VFM
Features
• Operating characteristics
– Voltage range: 1.71 V to 3.6 V
– Flash write voltage range: 1.71 V to 3.6 V
– Temperature range (ambient): -40°C to 105°C
• Core
– Up to 50 MHz V1 ColdFire CPU
– Dhrystone 2.1 performance: 1.10 DMIPS per MHz
when executing from internal RAM, 0.99 DMIPS
per MHz when executing from flash memory
• System
– DMA controller with four programmable channels
– Integrated ColdFire DEBUG_Rev_B+ interface with
single-wire BDM connection
• Power management
– 10 low power modes to provide power optimization
based on application requirements
– Low-leakage wakeup unit (LLWU)
– Voltage regulator (VREG)
• Clocks
– Crystal oscillators (two, each with range options): 1
kHz to 32 kHz (low), 1 MHz to 8 MHz (medium), 8
MHz to 32 MHz (high)
– Multipurpose clock generator (MCG)
• Memories and memory interfaces
– Flash memory, FlexNVM, FlexRAM, and RAM
– Serial programming interface (EzPort)
– Mini-FlexBus external bus interface
• Security and integrity
– Hardware CRC module to support fast cyclic
redundancy checks
– 128-bit unique identification (ID) number per chip
• Analog
– 12-bit SAR ADC
– 12-bit DAC
– Analog comparator (CMP) containing a 6-bit DAC
and programmable reference input
– Voltage reference (VREF)
• Timers
– Programmable delay block (PDB)
– Motor control/general purpose/PWM timers (FTM)
– 16-bit low-power timers (LPTMRs)
– 16-bit modulo timer (MTIM)
– Carrier modulator transmitter (CMT)
• Communication interfaces
– UARTs with Smart Card support and FIFO
– SPI modules, one with FIFO
– Inter-Integrated Circuit (I2C) modules
• Human-machine interface
– Up to 48 EGPIO pins
– Up to 16 rapid general purpose I/O (RGPIO) pins
– Low-power hardware touch sensor interface (TSI)
– Interrupt request pin (IRQ)
MCF51QU128
MCF51QU128
© 2010–2015 Freescale Semiconductor, Inc.
Table of Contents
1 Ordering parts.......................................................................................3
1.1 Determining valid orderable parts............................................... 3
2 Part identification................................................................................. 3
2.1 Description...................................................................................3
2.2 Format.......................................................................................... 3
2.3 Fields............................................................................................3
2.4 Example....................................................................................... 4
3 Terminology and guidelines.................................................................4
3.1 Definition: Operating requirement...............................................4
3.2 Definition: Operating behavior.................................................... 4
3.3 Definition: Attribute.................................................................... 5
3.4 Definition: Rating........................................................................ 5
3.5 Result of exceeding a rating.........................................................6
3.6 Relationship between ratings and operating requirements.......... 6
3.7 Guidelines for ratings and operating requirements......................6
3.8 Definition: Typical value............................................................. 7
4 Ratings..................................................................................................8
4.1 Thermal handling ratings............................................................. 8
4.2 Moisture handling ratings............................................................ 8
4.3 ESD handling ratings................................................................... 8
4.4 Voltage and current operating ratings..........................................8
5 General................................................................................................. 9
5.1 Typical Value Conditions............................................................ 9
5.2 Nonswitching electrical specifications........................................ 9
5.2.1
5.2.2
5.2.3
5.2.4
5.2.5
5.2.6
5.2.7
5.2.8
Voltage and Current Operating Requirements...............9
LVD and POR operating requirements.......................... 10
Voltage and current operating behaviors....................... 11
Power mode transition operating behaviors...................12
Power consumption operating behaviors....................... 12
EMC radiated emissions operating behaviors................16
Designing with radiated emissions in mind................... 17
Capacitance attributes.................................................... 17
5.4 Thermal specifications................................................................. 20
5.4.1
5.4.2
Thermal operating requirements.................................... 20
Thermal attributes.......................................................... 20
6 Peripheral operating requirements and behaviors................................ 21
6.1 Core modules............................................................................... 21
6.1.1
Debug specifications...................................................... 21
6.2 System modules........................................................................... 21
6.2.1
VREG electrical specifications...................................... 21
6.3 Clock modules............................................................................. 22
6.3.1
6.3.2
MCG specifications........................................................22
Oscillator electrical specifications................................. 24
6.4 Memories and memory interfaces................................................26
6.4.1
6.4.2
6.4.3
Flash electrical specifications........................................ 26
EzPort Switching Specifications.................................... 29
Mini-Flexbus Switching Specifications......................... 30
6.5 Security and integrity modules.................................................... 33
6.6 Analog..........................................................................................34
6.6.1
6.6.2
6.6.3
6.6.4
ADC electrical specifications.........................................34
CMP and 6-bit DAC electrical specifications................37
12-bit DAC electrical characteristics............................. 39
Voltage reference electrical specifications.....................42
6.7 Timers.......................................................................................... 43
6.8 Communication interfaces........................................................... 44
6.8.1
SPI switching specifications.......................................... 44
6.9 Human-machine interfaces (HMI)...............................................47
6.9.1
TSI electrical specifications........................................... 47
7 Dimensions...........................................................................................48
7.1 Obtaining package dimensions.................................................... 48
8 Pinout................................................................................................... 49
8.1 Signal Multiplexing and Pin Assignments...................................49
8.2 Pinout diagrams........................................................................... 51
8.3 Module-by-module signals.......................................................... 55
9 Revision History...................................................................................64
5.3 Switching electrical specifications...............................................17
5.3.1
General Switching Specifications.................................. 18
MCF51QU128, Rev. 5, 03/2015
2
Freescale Semiconductor, Inc.
Ordering parts
1 Ordering parts
1.1 Determining valid orderable parts
Valid orderable part numbers are provided on the web. To determine the orderable part
numbers for this device:
1. Go to
www.freescale.com.
2. Perform a part number search for the following partial device numbers: PCF51QU
and MCF51QU.
2 Part identification
2.1 Description
Part numbers for the chip have fields that identify the specific part. You can use the
values of these fields to determine the specific part you have received.
2.2 Format
Part numbers for this device have the following format:
Q CCCC DD MMM T PP
2.3 Fields
This table lists the possible values for each field in the part number (not all combinations
are valid):
Field
Q
Description
Qualification status
Values
• M = Fully qualified, general market
flow
• P = Prequalification
CF51 = ColdFire V1
JF, JU, QF, QH, QM, QU
• 32 = 32 KB
CCCC
DD
MMM
Core code
Device number
Memory size (program flash memory)
1
Table continues on the next page...
MCF51QU128, Rev. 5, 03/2015
Freescale Semiconductor, Inc.
3
Terminology and guidelines
Field
Description
Values
• 64 = 64 KB
• 128 = 128 KB
T
PP
Temperature range, ambient (°C)
Package identifier
V = –40 to 105
• FM = 32 QFN (5 mm x 5 mm)
• HS = 44 Laminate QFN (5 mm x 5
mm)
• LF = 48 LQFP (7 mm x 7 mm)
• LH = 64 LQFP (10 mm x 10 mm)
1. All parts also have FlexNVM, FlexRAM, and RAM.
2.4 Example
This is an example part number:
MCF51QU128VLH
3 Terminology and guidelines
3.1 Definition: Operating requirement
An
operating requirement
is a specified value or range of values for a technical
characteristic that you must guarantee during operation to avoid incorrect operation and
possibly decreasing the useful life of the chip.
3.1.1 Example
This is an example of an operating requirement:
Symbol
V
DD
Description
1.0 V core supply
voltage
0.9
Min.
1.1
Max.
V
Unit
3.2 Definition: Operating behavior
Unless otherwise specified, an
operating behavior
is a specified value or range of values
for a technical characteristic that are guaranteed during operation if you meet the
operating requirements and any other specified conditions.
MCF51QU128, Rev. 5, 03/2015
4
Freescale Semiconductor, Inc.
Terminology and guidelines
3.2.1 Example
This is an example of an operating behavior:
Symbol
I
WP
Description
Digital I/O weak pullup/ 10
pulldown current
Min.
130
Max.
µA
Unit
3.3 Definition: Attribute
An
attribute
is a specified value or range of values for a technical characteristic that are
guaranteed, regardless of whether you meet the operating requirements.
3.3.1 Example
This is an example of an attribute:
Symbol
CIN_D
Description
Input capacitance:
digital pins
—
Min.
7
Max.
pF
Unit
3.4 Definition: Rating
A
rating
is a minimum or maximum value of a technical characteristic that, if exceeded,
may cause permanent chip failure:
•
Operating ratings
apply during operation of the chip.
•
Handling ratings
apply when the chip is not powered.
3.4.1 Example
This is an example of an operating rating:
Symbol
V
DD
Description
1.0 V core supply
voltage
–0.3
Min.
1.2
Max.
V
Unit
MCF51QU128, Rev. 5, 03/2015
Freescale Semiconductor, Inc.
5
京公网安备 11010802033920号
EEWORLD
